The state machine of the game assumes that the user needs to
explicitly re-select multiplayer game when disconnected. We need to
therefore make sure that advertising stays off as soon as the first
connection happens.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Occasionally the sound might stay enabled for the restart timeout (2
seconds) if the ball would hit the wall right before missing the
paddle. Ensure that it's disabled whenever the game ends.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The buttons on the microbit cause quite easily "ghost" key presses.
Add a simple filter that ignores button presses from the same button
that happen less than 100ms from each other.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The stuff that the GPIO button callback does (in particular the printk
calls) requires more stack space from the ISR stack. Increase it to 1k
from the default 640.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This enabled testing CONFIG_BLUETOOTH_SHELL with configuration other
than btshell and enables ipsp sample to use bt shell module which
allows to disconnect, print metrics, etc.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This patch add arm core MPU support to NXP MPU driver.
With this feature it is now possible to enable stack guarding on NXP
MPUs.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Add beeps whenever the ball hits the walls or the paddle. Requires a
piezo buzzer connected to pin 0.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Add initial draft of a pong game using the display on the micro:bit
and its two buttons. This draft only supports a solo game where the
ball bounces from the "roof" and lets the player play against himself.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This gives a quicke example on how to use SPI asynchronous calls with
kernel's k_poll API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Adding a struct k_poll_signal parameter to driver's API unique
exposed function.
If not NULL, the call will be handled as asynchronous and will
return right after the transaction has started, on the contrary
of current logic where is waits for the transaction to finish
(= synchronous).
In order to save stack, let's move the device pointer to struct
spi_config. So the call is still at a maximum of 4 parameters.
Adapting spi_dw.c and spi driver sample to the change so it still
builts.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This application intents to test an SPI driver by looping over MISO/MOSI
line where the controller will then send data to itself.
It will test various buffer tx/rx schemes.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is not enough memory to run the HTTP server sample
application in Arduino-101 so remove the config file.
Jira: ZEP-2157
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This patch add a controller specific write function and fixes a
documentation error in the mpu_test README file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the mpu_stack_guard_test to the available samples.
The purpose of this test is to exercize the thread stack guard enabled
via MPU on arm platforms.
Change-Id: I4665a20956d9e6d0dd4b5cc862e82040a53afafc
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
This patch adds the Thread Stack Guards configuration option to the
synchronization sample.
This is meant to be an easy way to prove that the MPU can be dynamically
programmed on the supported platforms.
Change-Id: I77fbe6af3303ff8a2904768abd4cc9797f03c092
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
Rename SOC_STM32L476XX to SOC_STM32L476XG to keep flash
size information.
Aim is to be able to distinguish flash size variants of
the SoC when needed (for instance in dts/arm/st/mem.h file)
Change-Id: I834bb5b83c24c39e90c0492a2b22a7c7802de361
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Sometime it is observed on the Arduino 101 that when we write more than
4 bytes into TX USB Endpoint, first 4 bytes are getting repeated
(frequency of occurrence ~1/3000).
This patch does following :-
1. In sample application "cdc_acm", it adds capability to
handle partial transfer data incase data is transferred partially
if exceeds maximum data transfer size.
2. It restricts write of more than 4 bytes into TX USB Endpoint.
This is work around to avoid issue occarance.
Jira: ZEP-2074
Signed-off-by: Youvedeep Singh <youvedeep.singh@intel.com>
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_sample_app_init() is now able to wait that both IPv4
and IPv6 addresses are setup before continuing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Since more and more code is going to be reused by both the Host and the
Controller, this commit introduces a common/ folder that will contain
everything that is not tied to one of the two components but shared by
them.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Make sample working for other architectures.
SCSS_REGISTER_BASE and SCSS_SS_STS are defined in soc.h
Change-Id: Ie477520d2fb9bfcbbb5038ff42356a56d8180a1f
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Passkeys are always 6 digits in length and should therefore be
zero-padded if necessary.
Jira: ZEP-2113
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This creates a common API for network sample applications for
setting up IP addresses etc. The HTTP client application is modified
to use this API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to achieve proper sharing of configuration options, everything
that is common to both the Host and the Controller should now be placed
in the top-level Kconfig file, and Controller-only options are in the
controller/ Kconfig one.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
This commit provides sample application for sensor hts221.
By default, it is enabled on board disco_l475_iot1
Change-Id: I535fac8a670fa89cc1cae15ea1abe9cfe4b6c56b
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The files for the Arduino Due needed to be updated to use the new
configuration when the SoC moved from the atmel_sam3 directory to
the atmel_sam/sam3x directory.
Jira: ZEP-2067
Signed-off-by: Justin Watson <jwatson5@gmail.com>
Since most of nRF5x-based boards can be used either as a standalone
development kit or as a BLE controller to connect to an external host,
add DT overlays so that the baud rate is correctly set to 1Mbit/s
whenever building the hci_uart sample application.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
We're moving the project code to GitHub folks, so change references
in the documentation from gerrit over to GitHub:
https://github.com/zephyrproject-rtos/zephyr
Change-Id: Ic491a62ed43fc799eb5698e92435cb6eb4d89394
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
