board.h does not exist for any of the (official) Nordic nRF
boards. This commit corrects the information about the source
ofthe button and LED definitions.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Remove all references in the documentation and Kconfig options
to the legacy shell to avoid confusing users and developers
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Adds an fxos8700 device tree node to the mimxrt1050_evk. The sensor
interrupt gpios require a board modification to be used and conflict
with Ethernet and LCD signals, therefore their pinmuxes are not
configured.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the mcux lpi2c shim driver and pin muxes on the mimxrt1050_evk
board. Updates the board documentation and yaml supported list
accordingly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The schematic shows that both INT1 & INT2 from the MMA8652FC are wired
up, update the dts to reflect this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configuration of Erase command is specified in DTS. Hence
the corresponding changes in Kconfig are removed.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Number of sectors is now calculated from the flash density
i.e. (Flash size)/(sector size).
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The starting 192kB SRAM is reserved for the mcubootloader. Exclude
this region while building an application to be loaded by mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
FIFO_DEPTH should be in the SoC's Kconfig as this is a
configuration of SPI master controller in SoC.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patchset introduces partitioning of flash in terms of blocks
(flash page layout) for s1000. This partitioning is currently to
be used for mcubootloader.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Update boards yaml file with arduino_i2c supported option
We exclude disco_l475_iot1 from the x_nucleo_iks01a1 sample since there
are duplicated sensors between the disco_l475_iot1 and shield. Until
Zephyr drivers can handle multiple sensors we need to have this exclude.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables instance 3 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1060_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables instance 2 of the lpuart driver and configures pinmuxes to use
bluetooth hci on the mimxrt1020_evk board. Updates board documentation
accordingly.
Tested with samples/bluetooth/peripheral_hr, with frdm_kw41z attached as
an arduino shield running the nxp hci controller application.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This board has headers for these buses so they should be made available
without requiring special overlays.
Also take advantage of the new Nordic auto-enable for peripherals,
which eliminates the need for special configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Not all boards can get the coverage reports. The report generation
needs minimum of 64KB SRAM. This patch added support for mps2_an385,
qemu_cortex_m3, qemu_x86. This is just a subset. Also the previously
supported board native_posix is included in this patch.
If a board has 64KB RAM, it can generate reports by just
adding HAS_COVERAGE_SUPPORT in Kconfig.board.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Support musca board as a variant, it is a Cortex-M33 based SoC.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Signed-off-by: Minos Galanakis <minos.galanakis@arm.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit renames the CLOCK_CONTROL_NRF5 Kconfig symbol to
CLOCK_CONTROL_NRF. The change is required to aleviates confusion
when selecting the symbol in nRF9160 SOC definition.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update nucleo_l073rz to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
- update yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_l053r8 to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f446re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- disable I2C by default
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f411re to fit with default configuration guidelines:
- add spi support
- configure I2C1 as arduino i2c and spi1 as arduino spi
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f401re to fit with default configuration guidelines:
- configure I2C1 as arduino i2c and spi1 as arduino spi
- disable I2C and PWM by default
- update yaml
- update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f302r8 to fit with default configuration guidelines:
- remove reference to arduino_serial as Ardiuno D1/D0 are actually
mapped on PA2/PA3 which are already used for ST_Link com port,
hence not available by default for arduino serial
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update nucleo_f070rb to fit with default configuration guidelines:
-configure arduino spi and i2c
-update doc
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The test suite will use the m2gl025_miv.resc Renode script to load the
platform.
Signed-off-by: Dawid Wojciechowski <dwojciechowski@internships.antmicro.com>
Signed-off-by: Jan Kowalewski <jkowalewski@antmicro.com>
Signed-off-by: Piotr Zierhoffer <pzierhoffer@antmicro.com>
For normal (over-the-wire) mode of CAN sample lowering bitrate to
125000 to ensure reliable transfer on stm32f072b_disco boards
Signed-off-by: Andrei Laperie <andrei.laperie@intel.com>
Increase the size of the MCUBoot flash partition in the fstab-debugger
partition table, to accommodate for the RTT console and logs.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The MCUBoot partition in the default partition table (fstab-stock)
is not meant to accommodate an RTT console, since the board does
not have a SEGGER chip.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
Provide a dtsi file that sets up common capabilities for all
Feather-based Particle Mesh devices. Provide additional dtsi files for
some obvious peripheral options.
Remove the xtensa esp32 image: it didn't build, and there's no
indication of how the ESP32 firmware can be updated on the Argon board.
Use particle_argon as the nRF52840 side of the board.
Add Particle Boron support.
Note that dtsi files must be replicated in each board directory until
tooling supports DTS includes from a shared area.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This patch adds a x86_64 architecture and qemu_x86_64 board to Zephyr.
Only the basic architecture support needed to run 64 bit code is
added; no drivers are added, though a low-level console exists and is
wired to printk().
The support is built on top of a "X86 underkernel" layer, which can be
built in isolation as a unit test on a Linux host.
Limitations:
+ Right now the SDK lacks an x86_64 toolchain. The build will fall
back to a host toolchain if it finds no cross compiler defined,
which is tested to work on gcc 8.2.1 right now.
+ No x87/SSE/AVX usage is allowed. This is a stronger limitation than
other architectures where the instructions work from one thread even
if the context switch code doesn't support it. We are passing
-no-sse to prevent gcc from automatically generating SSE
instructions for non-floating-point purposes, which has the side
effect of changing the ABI. Future work to handle the FPU registers
will need to be combined with an "application" ABI distinct from the
kernel one (or just to require USERSPACE).
+ Paging is enabled (it has to be in long mode), but is a 1:1 mapping
of all memory. No MMU/USERSPACE support yet.
+ We are building with -mno-red-zone for stack size reasons, but this
is a valuable optimization. Enabling it requires automatic stack
switching, which requires a TSS, which means it has to happen after
MMU support.
+ The OS runs in 64 bit mode, but for compatibility reasons is
compiled to the 32 bit "X32" ABI. So while the full 64 bit
registers and instruction set are available, C pointers are 32 bits
long and Zephyr is constrained to run in the bottom 4G of memory.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Fix the QSPI and hyperflash nodes to be proper SPI children and expose
the address range for direct access as part of the controller's reg
region.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* i2c, spi, gpio are not tested, remove them now.
* fix the license issue in openocd.cfg
* fix the shell related setting
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The initial support of iotdk which is a board based on Synopsys
ARC IoT SoC.
In this commit, it includes
* processor support
* UART driver
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The mimxrt1020_evk and mimxrt1060_evk boards had invalid jlink device
names. Debugging via 'ninja debug' now works on these boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Fixes a Kconfig typo in the mimxrt1060_evk board that was introduced
when the board was split into separate hyperflash and qspi
configurations.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Moves the default TEXT_SECTION_OFFSET from the board level to the soc
level for the imx rt series. This offset is used to reserve space for
the imx boot header for external xip flash images.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add the codec reset GPIO to intel_s1000_crb's DTS
Update the DTS fixup for intel_s1000_crb accordingly
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Add board support files for mimxrt1020_evk, the development board for
i.MXRT1021 (CM7) SoC.
- Add pinmux, dts, doc.
- Code can be loaded to SRAM.
- Tested samples: hello_world, philosophers, synchronization,
basic/blinky, and basic/button.
Signed-off-by: Ryan QIAN <jianghao.qian@nxp.com>
Convert the w25qxxdv driver to use device tree for SPI device params.
Updated the Arduino 101 config to use device tree to specify the SPI
flash. Update the arduino_101_sss to drop Kconfig support for the
w25qxxdv flash.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
By default, after reset SWO signal is not connected to GPIO pin.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
By default, after reset SWO signal is not connected to GPIO pin. This
commit adds required initialization code to enable support for SWO
logger. Not all SoC series support the feature.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
lpuart1 is the default port used by ST-Link VPC.
Update board description to match out of box board configuration.
Fixes#12092
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Following recent renaming of STM32 UART Kconfig UART symbols,
LPUART was named as UART_LPUART_1.
Rename to LPUART_1.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
* Add DTS support for gpio controller driver
Signed-off-by: Ashokkumar B <ashokkumar@zilogic.com>
Signed-off-by: Subash G <subash@zilogic.com>
Signed-off-by: Vishnu K <vishnu@zilogic.com>
Signed-off-by: Vaishnavi D <vaishnavi.d@zilogic.com>
By adding 'aliases' node in SoC .dtsi file it is possible to generate
DT_ defines which specify a logical name rather than relay on module
location on APB bus. E.g. DT_SILABS_GECKO_USART_40010000_LABEL becomes
DT_SILABS_GECKO_USART_USART_0_LABEL. Thus it is possible to remove
dts_fixup.h defines.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
In 4940a3cac2 a compile time
check of the HW model version was added. This check worked
fine for cases in which the problem was that people had not
fetched a new enough version of the HW models.
But in some cases people will have fetched a new enough version
but be (unknowingly) in a past detached HEAD (or old tag).
With this change we ensure that the required tag is an actual
ancestor for the current HW models version HEAD
Also fail with an error, instead of just printing a warning.
Users can still disable this warning if they know what they are
doing.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The i2c_atmel_sam3 driver was deprecated at release 1.9, this commit
removes it. Also pinmux_dev_atmel_sam3x driver is removed.
i2c_atmel_sam3 was the last one which depended on it.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove configuration parameter CONFIG_BUS_TYPE. Now we may
make use of DT_ST_LSM6DSL_BUS_I2C and DT_ST_LSM6DSL_BUS_SPI
definition to select the bus.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
With this change, drivers or components can register on runtime
their own command line arguments.
What this change does is to use the dynamic command line arguments
API from BabbleSim's libUtil and provides a function for the
drivers to add their own.
Note that this change requires v1.3 of the HW models (which remove
a dependency on the board command line arguments structure)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
This function can only be used when the arguments structure memory
layout starts as in bs_basic_dev_args_t.
This assumption is just too dangerous in this board as somebody
may change the structure in the future unaware of this weird
requirement.
=> Do not use this function but do what it does in place.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
When the -nosim option is used the user may still want to set
either the simulation ID string (-s) or the device number (-d)
to control the tracing prefixes and/or dump folder, but may not
care to set both of them.
=> This change allows it, while the old behaviour is otherwise
maintained (setting both or none with -nosim)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Updated flash partitions to extend supported boot scenarios.
Add support for using Nordic nRF5 bootloader to:
- flash a Zephyr application
- flash a MCUboot image as an application
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
The en.high-perf_nucleo-144_mbed.jpg is an empty file.
This causes error when generating PDF documentation
as the tool cannot deal with empty image files.
So replace it with the image with same filename from
nucleo_f765zg, as the images are identical from
the online product description pages.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
interface/stlink-v2-1.cfg and interface/stlink-v2.cfg are wrappers
around interface/stlink.cfg, their inclusion trigger warning which
this change addresses. Besides the warning there is nothing there
except sourcing iterface/stlink.cfg directly.
Signed-off-by: Vasili Slapik <vslapik@gmail.com>
This mode allows the USB driver to use MSI clock as source clock.
MSI PLL-Mode permits +/-0,25% accuracy.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
The L476RG does not use the same I2C instance as the other L4 boards.
Correct the pinmux and add the peripheral.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
patch set the config USB_DFU_MAX_XFER_SIZE to 4096. This will
reduce the time required for flashing.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Document CAN support for board nucleo_l432kc and
add can to board yaml "support" section.
Fixes#12052
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fix misspellings in documentation (.rst, Kconfig help text, and .h
doxygen API comments), missed during regular reviews.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enable by default the following hardware instances in Kconfig:
- ADC_0
- I2C_0
- SPI_1 (SPI_0 for nRF52810)
for all nRF development kit boards having the corresponding DT nodes
enabled. This way there is no need to enable these instances in
particular applications, like samples for sensors or tests for drivers.
I2C_0 and SPI_0 cannot be used simultaneously in most of nRF SoCs,
nRF52810 is the only exception so far (and in this SoC SPI_1 is not
present, hence SPI_0 is enabled for it).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fixes board PHY initialization.
ENET_RST and ENET_INT pins are also used as USER_LED/JTAG_TDI and
INT1_COMBO/JTAG_TDO. Initialization needs to set these pins to power and
interrupt for the PHY Transciver. PHY reset works without busy waiting.
Moved pin initialization back to PRE_KERNEL_1 to fix UART bug and busy
wait not required.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Added warnings in documentation, pinmux and dts highlighting a potential
conflict if using SPI_1 and on-board ethernet at the same time.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Added board definitions for nucleo_f756zg. Features include gpio,
pinmux, uart (ST Zio, ST-Link and Arduino Uno v3 interfaces).
Added basic documentation and some soc definitions for the
stm32 f756XX soc.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
Updated .dts and pinmux.c to highlight pin conflict on PA7 if ETH and
SPI_1 are selected together without modification.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
STM32 uart Kconfig instance flags were not following
same naming scheme than other drivers (i2c, spi, ..)
Update driver to use UART_X instead of UART_STM32_PORT_X
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This patch cleans up the code in the recently added dts_fixup.h,
restoring the original alignment of the file.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
The dts.fixup for mps2_an385 contains a wrong setting for the IRQ fixup
for the Dual Timer IRQ.
This patch fixes the symbol included in the generated header.
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@linaro.org>
To enable the Hyperflash you have to physically modify the board and
this disables the QSPI. Since we plan on removing Kconfig from device
trees, its easier to treat the hyperflash as a separate board config
and thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This driver introduces an emulated LCD display for the native POSIX
board. The emulated display driver makes use of SDL2 to render the
displays frame buffer into a dedicated desktop window.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'make flash' always erase the flash banks from sector 0, and flashing
the Zephyr.bin file to base address of flash even if there has a
bootloader placed on the first sector.
Users maybe want placed Zephyr to another location instead of sector
0 by adding 'zephyr,code-partition' in dts. But the openocd scripts
doesn't deal with that currently.
Fix this issue, flash zephyr.elf instead of zephyr.bin, elf file
contain load address and openocd scripts can deal with it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
In commit d8e3ea6bc2
the LF clock interrupt was enabled, which causes its interrupt
handler to be used. This interrupt handler interacts with the
NRF_POWER registers.
Therefore require using the newer HW models which include a stub
of this registers.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Modify board stm32_min_dev aka "blue pill" led pin assignment in dts
from PB12 to PC13.
This board has a user led connected to PC13.
Sample blinky and similar would run out-of-box without additional
circuit to readout PB12 level.
Tested blinky on corresponding board.
Signed-off-by: Stephen Yi <stephen.jin.yee@gmail.com>
"-machine type=pc-0.14" appears to be the option which leads to
broken PCI emulation in QEMU, where PCI enumeration reports one
IRQ number (11), while actually IRQ 10 is emulated by QEMU.
"-vga none" and "-display none" appear to be just subordinate of
"-machine type=pc-0.14" and are required to get qemu_x86 into
bootable state.
Fixes: #11706
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There are different interrupt numbers for R22 v R23. Before this was
being handled via using Kconfig symbol CONFIG_BOARD_EM_STARTERKIT_R23 in
emsk_dt.h. Since we want to remove use of Kconfig in dts we handle this
via different dtsi files and having the proper one included by the
proper board revision dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards removing Kconfig from DTS we need to move setting of the sizes
of ICCM/DCCM into the SoC specific DTS files and out of emsk_dt.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add documentation for the quark_se_c1000_devboard with links to platform
guidelines and other details.
Fixes#11166
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added description how to build, programm and see console output of
hello_world example on cy8ckit_062_wifi_bt_m0 board.
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
The EFM32 Pearl Gecko Starter Kit contains sensors and
peripherals demonstrating the usage of the EFM32PG MCU
family. This patch adds basic support for this board
and is copied from EFM32WG-STK3800.
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for debugging and flashing the mimxrt1050_evk board via
pyocd. Support for this board has not yet been merged in upstream pyocd,
therefore the default in zephyr is left as jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merge up_squared_dts_fixup.h and up_squared_sbl_dts_fixup.h into
dts_fixup.h. This allows us to remove BOARD_DIR from being included
everywhere.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables Networking hardware on i.MX-RT 1050-EVKB board.
Pinout enabled board specific etherenet connection, also pin
initialization was moved later to PRE_KERNEL_2 in order to have
sysclock initialized before.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Fix link text to remove substitutions that are ignored by Sphinx. Also
replace link to Quark SOC HW ref manual to be from an Intel site (not
Russian).
Fixes: #11516
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Enabled Messaging Unit B in Cortex-M4 core of Udoo Neo Full board
so it can use IMX IPM.
Origin: Original
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Not pretty to change the PAD name from 2 to 1 as the correct
is PAD2 but for the SAMD20 the register value is 1.
Fixes: 6d08958ad5 ("drivers: uart_sam0: move sercom pad info to dts")
Signed-off-by: Sean Nyekjaer <sean.nyekjaer@prevas.dk>
Added support to the ti,cc2520 binding for optional GPIO signals and
moved the quark_se_c1000_devboard to define those signals in the DTS.
This lets us remove board.h and some #defines & fake Kconfig symbols
from the quark_se_c1000_devboard board.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The CC2520 device is specific to the quark_se_c1000_devboard not the
intel curie SoC. Move the device node where it belongs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that the in tree user of cc2520 uses device tree to configure SPI
and GPIO params, we can remove and convert the driver to utilize DT
only. This means removing the Kconfig options that come from DT and
rename CONFIG_ to DT_ for those options.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that all SPI controllers support DTS we can remove the Kconfig
support for non-DTS options. We also cleanup some defines that should
have be DT_MCR20A_ instead of CONFIG_MCR20A_.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The majority of cases of CONFIG_I2C_x_IRQ_PRI should be
DT_I2C_x_IRQ_PRI. So go ahead and fix them up. Only the i2c_nios
driver still uses Kconfig for getting priority.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This adds a primitive board configuration for the UP Squared board to
work properly with SBL(Slim Bootloader).
- https://github.com/slimbootloader/slimbootloader
- https://slimbootloader.github.io/
BOARD shall be 'up_squared_sbl'
cmake -GNinja -DBOARD=up_squared_sbl ..
ninja
Signed-off-by: Aiden Park <aiden.park@intel.com>
Remove the ifdef related to CONFIG_FS_FLASH_STORAGE_PARTITION. There
shouldn't be any harm in always having the partition around as we'll
just generate the defines related to and most applications will ignore
them.
Helps get one step closer to have DTS not depend on Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the
nrf52840_pca10056 board and should be maintained and configured
outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The wncm14a2a modem is an add-on/shield and not part of the nrf52840_mdk
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we just had the kernel's implementation, we could
just move this to lib/, but possible arch-specific
implementations dictate that we just make this a
syscall.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As explained in issue #8915 the STM32F4xx SoC family I2C
does not work well in Standard mode (100KHz). So let's
configure i2c3 in Fast mode (400KHz).
Signed-off-by: Armando Visconti <armando.visconti@st.com>
We should let drivers or board code include soc.h directly so we can keep
board.h to local info for board specific code.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
