Replace the legacy flags that assumed active level was relevant
only to input signals with the generic active level flags used
in Linux.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Mark the INT signal to be active low and use the new functions to get
gpio state and configure the gpio interrupt flanks.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
Remove link board can, shield was discontinued in
prototype status and will be replaced by a successor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
This shield adds analog and digital sensors to a TI LaunchPad
development kit. Currently only the ADXL362 accelerometer is supported.
This is useful for exercising the SPI interface. The analog sensors will
be useful if we add support for the sensor controller and ADC in the
future.
Signed-off-by: Brett Witherspoon <spoonb@cdspooner.com>
Add shield definition for the Texas Instruments LMP90100 Sensor Analog
Frontend (AFE) Evaluation Board (EVB).
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Move adafruit_2_8_tft_touch_v2 to Kconfig.defconfig format.
As part of this change Kconfig flags SPI and DISPLAY are removed
from the shield configuration as they are part of application
configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move dfrobot_can_bus_v2_0 to Kcondig.shield foramt and as part of
this change introduce nrf52_pca10040 board specific configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move link_board_can to conditional Kconfig.
As part of this change, some board specific symbols are moved
to reel_board specific file.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move sparkfun_sara_r4 to conditional Kconfig.
As part of this change, remove disco_l475_iot1 specific configuration
as it is already part of board default configuration.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Factorize definitions for ssd1306_128x32 and sd1306_128x64 shields
and move to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(I2C, SSD1306) are removed as they are application responsibility.
Also disabling SSD16XX is removed as SSD16XX should not be enabled
by default.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move wavehare epaper shields to conditional Kconfig.
As part of this change, direct drivers Kconfig symbols enabling
(SPI, SSD16XX) are removed as they are application
responsibility. GPIO is removed as well as it should be 'y' by
default on all boards according to Default board configuration
guidelines.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE subsystem can now be selected by application
using NETWORKING symbol, similarly to what is done when modem is
directly present on board.
Additionally, move board Kconfig files to a similar scheme where
shields related Kconfig flags are made available under shield,
board and NETWORKING symbols.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Put shield configuration Kconfig flags in new Kconfig.defconfig.
This way shield BLE susbystem can now be selected by application
using BT symbol, similarly to what is done when BlueNRG ship is
directly present on board.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
On LSM6DSO sensor the INT1 pin is used for both generating the drdy
interrupt and for switching to I3C hotjoin mode just after reset if
it is at logical '1' level. If you reset the x_nucleo_shield3 board
the LSM6DSO enter in hot join, as INT1 '1' level is preserved by
the level shifter.
This commit switch to INT2 to generate DRDY interrupt, so that INT1
always remain to logical '0' level.
Fixes: #20933
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Update shield description and sample to allow testing of LIS3MDL
sensor IRQ pin.
Update sample yaml file to state dependency on arduino_gpio.
Additionally, fix redundant line in sample yaml
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add configuration file for the stm32mp157c_dk2.
Beacon, Central are working.
Peripheral is not compiling because of .elf exceeding FLASH region,
else should be working.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add shield x_nucleo_idb05a1.
Tested samples with the disco_l475_iot1 (SPI3 disabled to ensure
to test the shield on SPI1, and not the on-board BlueNRG-MS chip):
Beacon, Central and Peripheral have been tested and are working.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Erwan Gouriou <erwang.gouriou@linaro.org>
