The FT5336 driver has been improved and generalized so that multiple
Focaltech touch controllers can be supported using the same single
driver. According to specifications the following list of controller
variants should be supported: FT5x06, FT5606, FT5x16, FT6x06, Ft6x36,
FT5x06i, FT5336, FT3316, FT5436i, FT5336i and FT5x46.
Tested using ER-TFTM028-4 display module (FT6X06).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The EFR32MG21 uses a different kind of clock for watchdogs.
It requires an additional peripheral-id parameter in the dts to get the
proper clock as it is based on the watchdog's ID i.e., cmuClock_WDOG#.
Signed-off-by: Steven Lemaire <steven.lemaire@zii.aero>
The peripheral is the same on the SAMD20 and SAMD21 except for
different clock and interrupt settings. There is no DAC on the SAMR21.
Leave disabled by default as the DAC is fairly power hungry.
Signed-off-by: Michael Hope <mlhx@google.com>
This commit enables support for parsing 'fixed-link' node when it
is added to node described in 'ethernet,fixed-link.yaml'.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch adds description for 'fixed-link' node in ethernet DTS
node. It supports setting speed and duplex.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit adds the device tree nodes and bindings for the I2C
controllers of the LPC11U6X MCUs
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This commit adds basic support for the clock controller used in
lpc11u6x MCUs.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This commit adds a bindings for the clock controller used in lpc11u6x
MCUs. It also adds a clock-controller node for the lpc11u6x soc series.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This patch adds the DT nodes and binding for the pinmux registers,
aka IOCON (I/O control), found on the LPC11U6x MCUs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
Now that the patches have landed, enable more of the peripherals on
the board.
In particular:
* Enable PWM on the LED
* Enable the SPI, USB, and DMA
* Enable the bootloader support
* Add to the PWM and SPI tests
* Call these out in supported.yaml
Signed-off-by: Michael Hope <mlhx@google.com>
Remove the device_type = "memory" property from the PSRAM node. We make
the slightly arbitrary distinction of using 'mmio-sram' compatible for
memories that don't need some kinda of dram style configuration or may
be on die.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For true mmio-sram, arc,iccm, arc,dccm nodes we should not be setting
device_type = "memory". This should be used for true DRAM regions of
memory and not on SoC SRAMs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
* Rename DT_SRAM_SIZE to DT_DRAM_SIZE since that is more correct
* Remove mmio-sram compatible since that is not correct for DRAM.
* Rename node label from sram0 to dram0
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add support for wsen-itds 3-axis accel sensor, provides acceleration,
temperature data reading and supports configuring of output data rate,
operating mode and scale.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
The parameters for this fuel gauge depend on the hardware design and
the expected battery. These should not be defaulted to a value that
may be inappropriate. Require that they be explicitly provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add Xplained-Pro header connector defined by Atmel. This allows
hardware with compatible headers to define the related GPIOs.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add Xplained header connector defined by Atmel. This allows hardware
with compatible headers to define the related GPIOs.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add support to STM IIS2DH the ultra-low-power highperformance
three-axis linear accelerometer.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add option to concatenate i2c transfers. If concatenation buffer size is
provided then transfers will be concatenated as long as there is space
left in buffer.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
We deprecated a number of aspects of the DTS binding syntax in Zephyr
2.1. Remove the support for the deprecated syntax. Remove from docs
about the deprecated syntax as well.
Removed reference in release-notes-2.1.rst to legacy_binding_syntax
since that anchor doesn't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
compatible = "arm,cortex-m33f" was already used for some time
(lpc55S6x, nrf9160...) without any related bindings.
Every works fine until you need to access one CPU node property
(eg. clock-frequency)...
Signed-off-by: Arnaud Mouiche <arnaud.mouiche@invoxia.com>
Several peripherals are non-functional in the ENG_A revision
of nRF5340 (Application MCU) so we delete the corresponding
DTS nodes in the device description.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Rename the nRF5340 QKAA variant .dtsi headers (Application
MCU) by adding an Engineering A (Eng A) suffix. This is done
to indicate that the headers should be explicitly used when
building for a board that contains the Engineeering A nrf5340
SoC variant.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
We need to use CPUAPP and CPUNET instead of CPU0 and CPU1
terminology, because those terms are the ones used
throughout the DeviceTree definitions for nRF5340 SoC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move the definition of the number of MPU regions
(num-mpu-regions) in a SoC variant-specific header
instead of the common .dtsi for nRF5340 Application
MCU. This allows us to define different SoC variants
with different number of MPU regions available.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
