Don't assume in the soc level device trees that flexcomm nodes will
always be configured as spi. Instead, configure flexcomm nodes at the
board level for lpcxpresso55s69 and lpcxpresso54114 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The board name for the nRF52 DK, so far known as nrf52_pca10040, is
renamed to nrf52dk_nrf52832. Its documentation and all references
to its name in the tree are updated accordingly. Overlay and
configuration files specific to this board are also renamed, to
match the new board name.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Kconfig options that enable I2C and SPI instances are no longer used
in nRF drivers. Remove all assignments done to these options in related
board definitions, samples, and tests.
For nrf52_pca20020, also no longer needed setting of default values
for GPIO_SX1509B* options is removed (now the gpio_sx1509b driver is
enabled by default when a corresponding devicetree node is enabled).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF51 Dev Kit board target (nrf51_pca10028)
to nrf51dk_nrf51422. We update all associated references
in the supportive documentation and all nRF51-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Since commit 22326f6d99 got in, this test
requires that so-called NOP frames (bytes of value 0) are sent when no
TX data is provided. For nRF SoCs, the over-read character (ORC) that
is sent in such case is by default configured to the value of 0xFF.
Alter configurations for nRF boards so that 0x00 is used instead.
On the occasion, remove redundant selections of driver type in those
configurations (CONFIG_SPI_x_NRF_SPI[M]=y), as such selections must
be aligned with the value of "compatible" property in corresponding
nodes in dts, so there's no much sense in having them separately here.
Correct also the SPI instance to be used for nrf51_pca10028.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Adds a board-specific configuration for the rv32m1 VEGAboard to the
spi_loopback test.
Enabled slave number 2, and turned on debug configurations to debug
effectively and from excess code being optimized out.
Signed-off-by: Jose Manuel Pacheco Luna <manuel.pacheco@nxp.com>
This patch enables SPI4 on the 96Boards STM32 Sensors Mezzanine.
SPI4 has been broken out to a Grove Connector on the board.
Changes:
- Updated board dts to enable spi4
- Updated board Kconfig
- Updated board documentation
- Update board pinmux
- Updated stm32f4 pinmux header file
- Updated stm32f401 dtsi
- Updated stm32f4 defconfig to enable PORTE GPIO
- Added board to spi_loopback test
Test: spi_loopback test passed
Signed-off-by: Sahaj Sarup <sahaj.sarup@linaro.org>
Adds board-specific configurations for the lpcxpresso54114 and
lpcxpresso55s69 to the spi_loopback test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The seasonal overhaul of test identifiers aligning the terms being used
and creating a structure. This is hopefully the last time we do this,
plan is to document the identifiers and enforce syntax.
The end-goal is to be able to generate a testsuite description from the
existing tests and sync it frequently with the testsuite in Testrail.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adding a Kconfig option for this test to configure the SPI in LOOP
mode. This saves physical wiring for hardware that support it.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Making CONFIG_SPI_ASYNC optional allows the test to be run on devices
where the feature is not yet supported in the driver.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Re-run with updated script to convert integer literal delay arguments
to k_thread_create and K_THREAD_DEFINE to use the standard timeout
macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add SPI support for stm32mp157c_dk2 board. If SPI is selected, SPI4
(Arduino connector compatible SPI) and SPI5 (on front 2x20 GPIO
expander) will be enable by default on stm32mp157c_dk2 board.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add the Atmel SAM R21 Xplained Pro Evaluation Kit to zephyr.
So far, UART, SPI, I2C (depends on #14128), debug LED and user button
have been tested.
Signed-off-by: Benjamin Valentin <benpicco@googlemail.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We use to define the SPI bus device name in Kconfig, however now that
all SPI bus controllers use DTS that comes from DTS, so SPI_1_NAME is
never set to anything. So remove it and leave it to the config frag in
the boards dir in the test to set the name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Port all users of 'set_conf_file' to use the built-in rules
instead. This follows the convention-over-configuration principle to
make the system as a whole simpler and more consistent.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The options selecting nRF drivers are now enabled by default when
an nRF SoC is selected as the build target.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
The $srctree environment variable gives the path relative to which
'(o)source' statements work (the current directory is used if $srctree
is unset). It is set to $ZEPHYR_BASE in cmake/kconfig.cmake, so there's
no need to qualify the source of Kconfig.zephyr in sample Kconfig files
(or in external projects).
All 'source's in Zephyr assume that the Zephyr root directory is used as
the srctree as well, and would break otherwise.
Remove the $(ZEPHYR_BASE)s to make it clearer that all 'source'
statements work relative to the Zephyr root. There was some user
confusion on IRC.
Also explain how things work in the documentation.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The Kconfig option CONFIG_BUILD_TIMESTAMP became unused when
BUILD_VERSION was introduced, but it's option and parts of it's
implementation was not completely cleaned from the repository.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
It is no longer necessary to set the KCONFIG_ROOT variable when the
KConfig file is in the application root directory.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
With the new Kconfig preprocessor (described in
https://github.com/torvalds/linux/blob/master/Documentation/kbuild/
kconfig-macro-language.txt), the syntax for expanding environment
variables is $(FOO) rather than $FOO.
$(FOO) is a general preprocessor variable expansion, which falls back to
environment variables if the variable isn't set (like in Make). It can
also be used in prompts, 'comment's, etc.
The old syntax will probably be supported forever in Kconfiglib for
backwards compatibility, but might as well make it consistent now that
people might start using the preprocessor more.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Prepend the text 'cmake_minimum_required(VERSION 3.8.2)' into the
application and test build scripts.
Modern versions of CMake will spam users with a deprecation warning
when the toplevel CMakeLists.txt does not specify a CMake
version. This is documented in bug #8355.
To resolve this we include a cmake_minimum_required() line into the
toplevel build scripts. Additionally, cmake_minimum_required is
invoked from within boilerplate.cmake. The highest version will be
enforced.
This patch allows us to afterwards change CMake policy CMP000 from OLD
to NEW which in turn finally rids us of the verbose warning.
The extra boilerplate is considered more acceptable than the verbosity
of the CMP0000 policy.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
The frdm_kw41z runs at a much slower clock frequency than the frdm_k64f.
Increase the k_poll timeout in the asynchronous callback thread to allow
the spi transaction to complete on frdm_kw41z.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The testcase was using only SYS_LOG_ERR() to signal error conditions,
which would print useful error information to the console, but allow the
test to pass when it should fail. Add zasserts after every SYS_LOG_ERR()
to make the test fail properly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
