This sample includes builtin UDP and TCP echo servers, max
MAX_CONTEXTS=3 as set previously, they just didn't work.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add an initial implementation for the Bluetooth Mesh Profile
Specification. The main code resides in subsys/bluetooth/host/mesh and
the public API can be found in include/bluetooth/mesh.h. There are a
couple of samples provided as well under samples/bluetooth and
tests/bluetooth.
The implementation covers all layers of the Bluetooth Mesh stack and
most optional features as well. The following is a list of some of
these features and the c-files where the implementation can be found:
- GATT & Advertising bearers (proxy.c & adv.c)
- Network Layer (net.c)
- Lower and Upper Transport Layers (transport.c)
- Access Layer (access.c)
- Foundation Models, Server role (health.c & cfg.c)
- Both PB-ADV and PB-GATT based provisioning (prov.c)
- Low Power Node support (lpn.c)
- Relay support (net.c)
- GATT Proxy (proxy.c)
Notable features that are *not* part of the implementation:
- Friend support (initial bits are in place in friend.c)
- Provisioner support (low-value for typical Zephyr devices)
- GATT Client (low-value for typical Zephyr devices)
Jira: ZEP-2360
Change-Id: Ic773113dbfd84878ff8cee7fe2bb948f0ace19ed
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
It's expected that there will be few socket-based samples, so move
tehm under samples/sockets/ to not clutter the main dir.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Implements asynchronous TCP echo server using non-blocking sockets
and poll, with concurrent connections support.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The coaps server sample application did not start because
number of IPv6 multicast addresses was too low. Increased
the address count from 2 to 5.
Jira: ZEP-2359
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The macros for calculating the length of the configuration
descriptors have been interchanged, fix it, and use the
correct macro for the length of the DFU mode configuration
descriptor.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
According to RFC7959 page 30, "The end of a block-wise transfer is
governed by the M bits in the Block options, _not_ by exhausting the
size estimates exchanges."
Therefore, we should check the M bit instead of total size (which
is not always available, too)
Signed-off-by: Robert Chou <robert.ch.chou@acer.com>
This disable debug options in order for the image to fit in boards
such as arduino_101 and quark_se_c1000_devboard.
For convenience this adds another configuration file with as it was
available previously which can be build using:
make CONF_FILE=prj_dbg.conf
JIRA: ZEP-2378
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Some README files referenced wiki articles that have been
moved to the doc area on the website.
Fixes#668
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Upcoming memory protection features will be placing some additional
constraints on kernel objects:
- They need to reside in memory owned by the kernel and not the
application
- Certain kernel object validation schemes will require some run-time
initialization of all kernel objects before they can be used.
Per Ben these initializer macros were never intended to be public. It is
not forbidden to use them, but doing so requires care: the memory being
initialized must reside in kernel space, and extra runtime
initialization steps may need to be peformed before they are fully
usable as kernel objects. In particular, kernel subsystems or drivers
whose objects are already in kernel memory may still need to use these
macros if they define kernel objects as members of a larger data
structure.
It is intended that application developers instead use the
K_<object>_DEFINE macros, which will automatically put the object in the
right memory and add them to a section which can be iterated over at
boot to complete initiailization.
There was no K_WORK_DEFINE() macro for creating struct k_work objects,
this is now added.
k_poll_event and k_poll_signal are intended to be instatiated from
application memory and have not been changed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Initialize the buffer to 0 and read one byte less than the
buffer size. The result should be that the last byte of
the buffer always stays 0. This way it is possible to verify
it the driver does not write outside the buffer.
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Remove NET_UDP_HDR() macro as we cannot safely access UDP header
via it if the network packet header spans over multiple net_buf
fragments.
Fixed also the UDP unit tests so that they pass correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The config file for KW40Z has the shell disabled, as available
SRAM memory is limitted to 16kB.
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
CONFIG_NET_IF_UNICAST_IPV6_ADDR_COUNT should be used instead of
CONFIG_NET_IFACE_UNICAST_IPV6_ADDR_COUNT.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Since the controller comes with a transmit buffer size that mirrors the
maximum size of a transmit packet, use that to size the buffers that are
used in the hci_uart application to receive packets from the Host over
the UART.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The worst-case maximum number of CCC entries we need is actually
MAX_CONN + MAX_PAIRED. Provide a helper define for it and use it
whenever appropriate.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Explicitly select CONFIG_BLUETOOTH_BROADCASTER and
CONFIG_BLUETOOTH_OBSERVER in the scan_adv sample.
If the Controller is included without connections support
then only broadcaster support is compiled in by default,
hence add broadcaster and observer role support explicitly
in the prj.conf file.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Next two commits will increase the mbedtls ram usage a bit and
https client and server sample test will fail.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the net app API is automatically initialized, there is no
need to call net_app_init() by the http client and server sample
applications.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Removing CONFIG_NET_APP_SETTINGS from prj.conf file as the
sample does not use or need any IP addresses.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit will convert echo-client to use the net app API
when creating the connection to peer. Most of the network
setup code will be removed from echo-client by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit will convert echo-server to use the net app API
when creating the listening service. Most of the network
setup code will be removed from echo-server by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The network application API is a higher level API for creating
client and server type applications. Instead of applications
dealing with low level details, the network application API
provides services that most of the applications can use directly.
This commit removes the internal net_sample_*() API and converts
the existing users of it to use the new net_app API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We get some failures to build if we don't filter this test to only
boards that support uart interrupts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Makefiles which start QEMU (make run) have been changed to operate
off of the QEMU_INSTANCE variable. QEMU_INSTANCE is simply appended
to the pid and sock file names. This makes us able to run multiple
QEMU Zephyr instances of the same sample.
Signed-off-by: John Andersen <john.s.andersen@intel.com>
There were a few different issues with the UART_CONSOLE filtering:
* Filter was incorrect - UART_CONSOLE should be CONFIG_UART_CONSOLE
* platform_exclude was used for drivers that had a #error for lack of
interrupt support. We can now use CONFIG_SERIAL_SUPPORT_INTERRUPT in
the filter for that. This catches all the various drivers that needed
don't support uart interrupts, not just the onces that had a #error
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch allows more generic USB configuration in the samples
and removes platform dependent driver configuration.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Where possible, replace the use of filter with newly added keywords.
This will speed things up and in some cases add more coverage due to bad
filters.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The example source code is POSIX-compatible (modulo include files),
i.e. can be built and behaves the same way for Zephyr and a POSIX
system (e.g. Linux). Makefile.posix is available for the latter.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
