Fix the ns16550 uart driver and relevant SoCs accordingly.
All generic settings are now DTS based.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Fix the qmsi uart driver and relevant SoCs accordingly.
Also: using config for irq everwhere relevantly and not an hardcoded
value in the driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name generated through dts as well.
Fix the rtc driver and relevant SoCs accordingly.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Get the name and irq flags generated through dts as well.
Fix Kconfig for the gpio driver accordingly.
Irq priority is not set by dts for D2000 as it's irq controller does
not support it.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the i2c controller
on quark_d2000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the 2 i2c controllers
on quark_se_c1000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Applying the change to relevant arch/boards, either in their Kconfig or
the dts specific files.
Taking the opportunity in dw driver to rename the variable the same way
as they are everywhere else in the code (s/dev/dw and s/port/dev) in
init function.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This will generate the necessary configuration for the i2c controller on
quark_x1000.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
patch removes the mem.h and marcos used in that file are
moved appropriate board files. As there are boards with
different flash configuration but of same soc, flash and
ram size are moved to dts file instead of dtsi
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
When CONFIG_X86_MMU is enabled for arduino 101 the start address
should be aligned to 4kB. If not aligned the page tables would not
be created and the build fails.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Move the dts files into the board dir so that board ports can be more
standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the dts fixup files into the board dir so that board ports can be
more standalone. This will allow us at some point to have board ports
outside of the tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The port will enable Zephyr to run as a guest OS on x86-64 systems. It
comes with a test on QEMU to validate that, thus this new board
introduction. It's "make run" target will issue QEMU with the same
configuration Jailhouse upstream uses for their confis/qemu-x86.c root
cell configuration:
Test configuration for QEMU Q35 VM, 1 GB RAM, 4 cores,
6 MB hypervisor, 60 MB inmates (-4K shared mem device)
This will work provided qemu-system-x86_64 is installed in the system
and a given (qcow2) image with the Jailhouse root cell in it is
provided (any of those will ever ship with Zephyr, it's out of its
scope).
Signed-off-by: Gustavo Lima Chaves <gustavo.lima.chaves@intel.com>
Moved yaml files to be under dts/bindings and have the bindings try
and match the linux doc device tree binding dir structure as the
canonical binding reference.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
1. Use compatible "ns16550" to match upstream binding
2. Add reg-shift as optional property to binding yaml
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch add device tree support for develoement board of
quark_se_c1000. Previously pushed patch was flashing binary
at wrong address because of which UART was not working
Jira:ZEP-2459
test
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
As the device tree is board specific we should be using the board
Kconfig variable to decide which .dts to use and not the SoC one for
arduino_101.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
patch fix the build warning generated while building
application for quark_d2000. This is a fix for Jira ZEP-2437
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
Remove memory node from skeleton dtsi and add device_type
property in every memory node in soc dtsi files
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This patch adds #address-cell, #size-cell properties to
cpus container node and device_type, reg properties to
cpu node.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
patch adds zephyr,bt-uart, zephyr,uart-pipe and zephyr,bt-mon-uart
to device tree as chosen property.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch adds necessary files and does the modification
to the existing files to add device support for
arduino_101 board.
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch enables qmsi serial driver to pick baudrate and name
from device tree instead of Kconfig for UART0 and UART1
instance
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
patch adds necessary files and does the modification to the existing
files to add device support for x86 based intel quark microcontroller
Signed-off-by: Savinay Dharmappa <savinay.dharmappa@intel.com>
