Update bluetooth hcp_spi sample to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Introduce define for dt generated gpio flags
- Update 96b_carbon_nrf51.dts according to new bindings
- Gpio IRQ pin is configured to output inactive
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use the flags included in the new GPIO API to describe the properties of
LEDs and buttons in the device tree source files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Update devicetree sources and bindings, switch to new GPIO API. Use
devicetree property name to identify interrupt signal.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new pin and interrupt configuration API. Update all
devicetree bindings to add INT signal active level. Document active
level.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the GPIO_ACTIVE_LOW to signal that the button pins are active low,
instead of the deprecated GPIO_INT_ACTIVE_LOW.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Converts the sdhc spi driver to the new gpio api. Updates device trees
for the olimexino_stm32 and nrf52840_blip boards to set appropriate
active high/low polarity for the spi chip select pin.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the fxas21002 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on the hexiwear_k64 board.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Update bluetooth hcp spi driver to new GPIO API.
Following changes have been done:
- Use new gpio api functions
- Get reset, irq and cs flags from dt defines
- Define reset pin as active low and invert set/unset logic.
Tested on disco_l475_iot1 and 96b_carbon.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Converts the fxos8700 sensor driver to the new gpio api. Updates device
trees for all boards with this sensor to active low gpio interrupts by
default.
Tested on frdm_k64f and rv32m1_vega_ri5cy boards. The latter verifies
that the reset output works correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Converts the usdhc driver to the new gpio api. Updates the
device tree for the mimxrt1050_evk board to set appropriate active
high/low polarity for the power and card detect pins.
Note that the driver doesn't actually support interrupts yet. It
initializes a gpio callback for the card detect pin, but never actually
enables the gpio interrupt. This incomplete behavior is left as-is,
since the purpose of this patch is only to convert the driver to the new
gpio api, not to add new features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
For this board all 16 pins on the SX1509B should be configured as
outputs. Six of them are active-low LEDs. Provide configuration so
those six are initialized to output high, and the remainder to output
low.
Two of the pins control the behavior of the CCS811 gas sensor. By
driving them low on boot the baseline current draw of the board is
reduced by 100 uA.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
In initialization code, pairs of gpio_pin_configure/gpio_pin_write are
replaced with calls to gpio_pin_configure that configure a given pin as
output with the proper initial state.
dts file for the board is also updated with the new GPIO flags.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In initialization code, pairs of gpio_pin_configure/gpio_pin_write are
replaced with calls to gpio_pin_configure that configure a given pin as
output with the proper initial state.
dts file for the board is also updated with the new GPIO flags.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Provide correct active level and pull on all signals. Use
init-to-active when configuring antenna switch.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Mark the INT signal to be active low and use the new functions to get
gpio state and configure the gpio interrupt flanks.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Update the code configuring pins that control the routing of certain
lines on the board, to take advantage of the introduced possibility
of configuring a pin as output with specified initial state.
Additionally, use `gpio_pin_get_raw` instead of `gpio_pin_get` for
checking the reset pin state, to save a few bytes in flash.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Correct DRDY active level to default active-high, switch to new
interrupt configuration.
Also fix a common bug where an already-active DRDY signal is not
properly handled.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Updates the rv32m1 gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Stops quietly reconfiguring pinmuxes to gpio mode. The pinmux must now
be configured explicitly in the board's pinmux.c or in the application.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
On boards:
- rv32m1_vega_ri5cy
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Use standard spelling for pull and active flags. Correct LED active
level (based on SAM-D21-Xplained-Pro).
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
Pins enabled to be used as GPIO for 2 pin test gpio_basic_api.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the mcux lpc driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle functions recently added to the gpio api.
ISR functions to be added later.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Updates the imx gpio driver and all associated boards to use new
device tree compatible gpio configuration flags. Implements new port
get/set/clear/toggle and pin_interrupt_configure functions recently
added to the gpio api.
Assumes the gpio api layer handles translating logical flags to physical
flags.
Tested with:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_api_1pin
- tests/drivers/gpio/gpio_basic_api
On boards:
- udoo_neo_full_m4
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
