If `CONFIG_BT_CENTRAL` was enabled and the device was not scanning
or connected, then `bt_le_per_adv_sync_create` would not start
scanning for periodic advertisers.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
Mark the ram version of the ccc_cfg as free after ccc has been
stored when a bonded device disconnects.
If the device use lazy loading of settings then ccc_cfg was not
cleaned up properly when a bonded device disconnects. This
resulted in the ccc system ran out of ccc_cfg resources after
having disconnected CONFIG_BT_MAX_CONN times.
Signed-off-by: Kim Sekkelund <ksek@oticon.com>
Step1: Move bt_gatt_disconnected() to avoid forward declarations which
otherwise would be needed by a fix to lazy loading cleanup on
disconnect in step 2.
Signed-off-by: Kim Sekkelund <ksek@oticon.com>
Since bt_l2cap_send_cb can fail returning its error is not enough as
the buffer has been modified to add the headers, so this save the state
before calling bt_conn_send_cb and takes a reference so it can be
restored its original state in case of error.
Fixes#27434
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Leave the SPI CS GPIO handling to the SPI controller driver and make SPI
CS GPIO optional for SDHC disk access via SPI.
The SPI SDHC implementation relies on SPI_HOLD_ON_CS so we need to
explicitly release the SPI controller driver after ending transmissions
to force the CS line to be de-asserted.
Fixes#27444.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
-Wimplicit-fallthrough=2 requires a fallthrough comment or a compiler
to tells gcc that this happens intentionally.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This adds a very primitive coredump mechanism under subsys/debug
where during fatal error, register and memory content can be
dumped to coredump backend. One such backend utilizing log
module for output is included. Once the coredump log is converted
to a binary file, it can be used with the ELF output file as
inputs to an overly simplified implementation of a GDB server.
This GDB server can be attached via the target remote command of
GDB and will be serving register and memory content. This allows
using GDB to examine stack and memory where the fatal error
occurred.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Added additonal checks in net_ipv6_input to ensure that multicasts
are only passed to the upper layer if the originating interface
actually joined the destination multicast group.
Signed-off-by: Philip Serbin <philip.serbin@lemonbeat.com>
In case when SMP has been enabled, the shell_thread would be signaled
even if no data has been read from fifo.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
In case when shell ring buffer gets full the data may still be taken
from the UART fifo, byte by byte, and accepted by the SMP back-end,
if the back-end has been enabled.
Unfortunately the uart_rx_handle failed to check if it has been
successfull in reading a byte from the fifo, before passing it to
the SMP for processing, which could lead to processing random stack data
as a part of an SMP frame.
Additinally, when the SMP would have accepted the byte,
the uart_rx_handle would fail to signal shell_thread, that the SMP has
internally buffered data that could be processed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Sort entries alphabetically and cleanup top level menu for each
subsystem. Move stats subsystem Kconfig from debug into its own Kconfig.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This one was appearing in the top level Kconfig menu when viewed in
menuconfig. Move it to where it belongs.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Elevate connections always to security mode 1 level 4 when
Secure Connections Only Mode has been enabled in the Security Manager.
Elevate connections always to security mode 1 level 3 when
Legacy pairing with OOB only has been enabled in the Security Manager.
Fixes: #27338
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Now that TCP2 is the default stack, make the shell compatible
with both stacks.
Note: net_tcp_foreach is not implemented in TCP2, so related
code depends on TCP1.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
PPP Phase Diagram [1] allows only one way phase change. In current
implementation there is an additional RUNNING phase, which is entered
just after NETWORK phase.
Prevent going back from RUNNING to NETWORK phase when Term-Req was
received, as this is meaningless for overall PPP operation and violates
PPP Phase Diagram property of having one way direction change.
This change also improves Adminitrative Close handling (calling
lcp_close()). This request results in moving into TERMINATE phase. Then
LCP is put down (by calling lcp_down()) and then ppp_link_down() is
called, which so far (before this patch) resulted in moving back to
NETWORK and then to DEAD. Right now (after this patch) we move directly
from TERMINATE to DEAD phase, which is exactly how [1] specifies it.
[1] https://tools.ietf.org/html/rfc1661#section-3.2
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
State Transition Table [1] specifies that Administrative Close should
result in CLOSING state. This is not respected in case of LCP, as
STOPPED state was forced in lcp_close().
Don't force going into STOPPED state in lcp_close() and rely on
ppp_fsm_close() to move to CLOSING state instead.
This patch fixes overall Adminitrative Close procedure and allows to
move back into fully operating PPP connection once again after
Adminitrative Open.
[1] https://tools.ietf.org/html/rfc1661#section-4.1
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
LOG_BACKEND_SPINEL_LEVEL turned out to be useless and was removed.
Also changes to keep coherence between Zephyr log level and OT log
level added by otPlatLog() were introduced.
Signed-off-by: Kamil Kasperczyk <kamil.kasperczyk@nordicsemi.no>
Many functions signal success by returning a return code of zero. Add
an assertion for this.
Some functions can return a positive value to indicate success, where
they want to convey some information. This is not handled by this
assert function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Print role information next to port information. Also make
sure that port number is set correctly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Save some memory and separate common string snippets from larger
strings. In this case "does not match" sub-string is printed by
several warning prints so separate the sub-string from the bigger
string.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Return BT_HCI_ERR_INVALID_CONN_ID if an invalid handle is
given by the HCI; currently sometimes BT_HCI_ERR_CMD_DISALLOWED
is returned
Signed-off-by: Andries Kruithof <Andries.Kruithof@nordicsemi.no>
So far SMP shell transport was initialized in APPLICATION run level, but
shell over UART was initialized in POST_KERNEL. This could end up in
situation when received frames were scheduled for further processing in
SMP layer, when it was not initialized yet.
Export smp_shell_init() function declaration and call it before shell is
initialized with all its receive data handlers. This prevents situation
when data is scheduled for processing in SMP layer, when that one is not
ready yet.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
net: route: Add prefix-based ipv6 multicast forwarding
This adds/reenables the feature of multicast routing/forwarding.
The forwarding decision is based on the added multicast routes
and the new network interface flag:
NET_IF_FORWARD_MULTICASTS.
Signed-off-by: Jan Georgi <jan.georgi@lemonbeat.com>
This commit fixes an issue when more than one USB transfer is
reserved for same OUT endpoint.
There are 2 scenarios when this could happen:
- The Host sends SET_CONFIGURATION(1) request twice.
- The Host triggers Suspend->Resume->Configured
event sequence for the device.
USB tranfers are not canceled on SUSPEND event
when the device was not configred previously.
Because of that USB transfer slot is reserved twice
for the same OUT endpoint and lead to shortage of USB
transfer slots quickly.
Without this patch CDC ACM class reserves duplicated USB
transfer slots for one transfer. The sequence of
Suspend->Resume events is genereted alongside with
Configured and the stack will shortly run out of transfer
slots.
If the Host, for some reason, decides to send
SET_CONFIGURATION request twice the same issue is seen.
This patch prevents from reserving additional USB transfer
slots twice.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This patch implements optional authentication phase, which is done
between link establishment and network phases. It is part of LCP option
negotiation to decide whether authentication is needed and which
protocol will be used. For now we add only PAP support and try to
negotiate it when some other protocol (e.g. CHAP or EAP) is proposed
earlier. For simplicity reason we only add one way authentication
support, which means that we try to authenticate to the other peer, but
do not require authentication from it.
This is an important step to make PPP work with cellular network modems,
because most of them require to provide username and password within PPP
authentication phase. Those credentials are used by modem to login to
cellular network. In most cases however it is enough to provide dummy
values, because they are not verified. For this reason and simplicity of
this patch we hardcode PAP Peer-ID and Password now.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This module had only some header includes, without actual code. Remove
it, as it is better to create one module per authentication protocol
anyway.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add enums of PAP, CHAP and EAP authentication protocols. Also add their
string representations, so they will nicely show up in logs during
debugging.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Interpret -EINVAL return value from options' parse() callback as "option
value is not supported". After receiving such value nack() callback will
be executed in order to put supported value in the response.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Shell will display a warning message if there was a request to print
a message on the not initialized shell backend.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
Disable shell print functions if the shell is not initialized.
Update tests accordingly.
Fixes#27161
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Given the comment in `ipv6_event_handler`, the init function shall wait
for the last added IPv6 address to be confirmed with DAD. This is
contrary with current logic, which will only wait for the first address
to be confirmed.
This commit adds a break statement in the loop, not to overwrite the
recent address to verify with an older one.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Removed the check for selected_per_adv_sync as it was unused by the
create/delete functions (which take the index as parameters), and
caused the shell not to print any values.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
The `free_per_adv_sync` pointer in `cmd_per_adv_sync_create`
did not work as intended, as it didn't actually update the
pointer in the array, which caused the
`cmd_per_adv_sync_delete` to not function as intended.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
In the function do_net_init() the paths for ipv6 and ipv4 now use the
same api to determine the source address.
Fixes#27428
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
When verifying the parameters check NULL value separately.
This will avoid nasty warning message to be printed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add function pointer to vtable and use that directly instead of
routing via ioctl() call. This is done as we are trying to get
rid of ioctl() calls in the system.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Do not route close() calls via ioctl() as that is error prone
and quite pointless. Instead create a callback for close() in
fdtable and use it directly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If CONFIG_BT_EXT_ADV was enabled but
CONFIG_BT_EXT_ADV_LEGACY_SUPPORT was disabled and
CONFIG_NO_OPTIMIZATIONS was enabled, then there was a
maybe-initialized warning. Fixed by adding additional
checks.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Instead of casting struct in6_addr, sin6_addr member is now used
directly, like in every other instance of calling net_ipv6_is_prefix().
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Core 5.2, Vol 4, Part E, section 5.3.1 clarifies that advertising set
handle is assigned by host when advertising set is created and this
happens only on LE Set Extended Advertising Parameters.
An advertising set handle is an arbitrary number within allowed range,
i.e. 0x00-0xEF and not 0..max_supported-1.
This patch adds option to enable advertising set handle mapping from
HCI range as defined by Core specification to zero-based handles used
by LL. If enabled, HCI handle will be remapped to LL handle for each
command, otherwise HCI handle will be used as an LL handle. The latter
effectively skips mapping logic and should be used with Zephyr host
which uses zero based indexes.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
There's not need to mark advertising set as created by either legacy
or advertising command since this is determined by current so-called
HCI advertising mode which determines whether host uses legacy or
extended advertising commands.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
As per Core 5.2, Part B, section 3.1.1 controller should not allow
mixing of legacy and extended advertising commands. Once 1st command
is received from host, we should only allow commands of the same type
and return an error on other commands.
If legacy advertising interface is selected by 1st command received,
we need to make sure that set with handle=0 is created since it's
used by all legacy commands.
When not using external host, we assume that only extended advertising
interface will be used thus all checks can be skipped (optimized and
compiled-out).
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
A lot of commands return CC event with status parameter only, especially
when error is returned. This patch adds a helper to create such event,
similar to cmd_status.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Proper error code should be returned if advertising set with given
handle does not exist instead of generic "invalid parameters" one.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Expose the exFAT support option to Kconfig, so developer can
enable/disable the exFAT support on FatFs through Kconfig, no need to
touch ffconf.h.
Signed-off-by: Jui-Chou Chung <jui-chou.chung@nordicsemi.no>
This macro has no use in code and was most probably replaced by
FSM_TIMEOUT (which resolves to CONFIG_NET_L2_PPP_TIMEOUT) with the same
default value.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Those macros are not used anymore after commit 35a2519091 ("net: l2:
ppp: add generic function for handling Conf-Req"), because we no longer
need preallocated table on stack for parsing option information.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This option is not used after commit 50b2cafc42 ("net: l2: ppp: use
net_pkt API for replying to Configure-Req") has been applied. We don't
need to preallocate table on stack for parsing option information, so
information about maximum number of supported options is useless.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
AdvA in extended advertising PDUs is put at different offset than in
legacy PDUs thus it's better to let caller calculate and pass AdvA and
TxAdd explicitly. This way we won't need to check whether scan request
was on legacy or extended PDU every time.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
When a connect indication contains a channel map of all zeros, the
adv->conn is left NULL'ed after return and next connect attempt leads
to a crash.
This was identified via the Sweyntooth test suite executing the script
re. issue 6.14 towards an Oticon target.
Signed-off-by: Erik Brockhoff <erbr@oticon.com>
This commit allows let build zperf sample with overlay-netusb.conf.
USB subsystem must be enabled by the application.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
usb_enable() must be called by the application.
The application may want to register usb_dc_status_callback
and trace usb status codes (usb_dc_status_code).
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Tracing backed is not checking if the chosen backed specifies
the init function and is asuming its always present which could
not be true.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Open Supervised Device Protocol (OSDP) describes the communication
protocol for interfacing one or more Peripheral Devices (PD) to a
Control Panel (CP). The PDs are slave devices that waits for commands
from a CP. The communication happens over a RS485 multi-drop connection
with specification for a secure channel communication.
This patch adds initial support for OSDP in PD mode without secure
channel.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
USB device shall be able to send only in CONFIGURED state.
Zephyr USB HID device class allows to send the data no matter
of the USB state what is wrong. Attempting to write to endpoint
buffer in state != CONFIGURED may lead to driver error.
This patch introduces state tracing for USB HID class and
allows to send data using hid_int_ep_write() class API
only if the device remains in CONFIGURED state.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This override header declares structures and inline functions, which
must be given C language linkage to avoid conflicting declaration
errors with other headers.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Move call to reset_pairing to bt_conn_security_changed, since this
should always be done at the same time, and should be done in the same
order for all calls. For auth_complete this was reset after the
callbacks, which is inconsistent with the other events.
Also call it even if not connected anymore, the disconnection complete
event will be delivered after this event. Callback should alway be
called if security was initiated.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
This commit adds comment clarifying how does DTS chosen node,
'zephyr,shell-uart', impacts default value of option assigning UART
port to the shell.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
For platforms using non-native stacks, net_tcp_init() should be
compiled out, similar to how it is done in tcp_internal.h.
Fixes#27463
Signed-off-by: Vincent Wan <vwan@ti.com>
Added support for syncing to periodic advetisements.
The API and usage is heavily inspired by the extended advertisement
and connection APIs.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
Added the ext adv report interval to bt_le_scan_recv_info which
denotes whether or not there is periodic advertisement data
associated with the advertisement report.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
Added API to set periodic adv parameters, periodic adv data
and to enable/disable periodic advertisement.
Signed-off-by: Emil Gydesen <emil_gydesen@bose.com>
When FAT FS option is enabled, then the FAT FS sub-menu will appear
next to it, instead of appearing far down the list.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
It does not auto-initiate the DLE procedure if the default data length
parameters are not equal to the initial parameters.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Some controllers do not follow the recommendation of auto-initiating
a data length update if the host writes default data length parameters.
If the controller follows this recommendation, calling
LE Write Suggested Default Data Length command is sufficient
to ensure that the LL will auto-initiate the DLE procedure. Performing
a second procedure is unecessary.
In Core v5.2, Vol 4, Part E, Section 7.8.35:
The HCI_LE_Write_Suggested_Default_Data_Length command allows the
Host to specify its suggested values for the Controller's maximum
transmission number of payload octets and maximum packet
transmission time for packets containing LL Data PDUs to be used
for new connections. The Controller may use smaller or larger values
for connInitialMaxTxOctets and connInitialMaxTxTime based on local
information.
In short, this command sets connInitialMaxTxOctets
and connInitialMaxTxTime.
In Core v5.2, Vol 6, Part B, Section 4.5.10:
For a new connection: connMaxTxOctets shall be set to
connInitialMaxTxOctets and connMaxRxOctets shall be chosen by the
Controller. If either value is not 27 then the Controller should
initiate the Data Length Update Procedure at the earliest practical
opportunity.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Fix issue with bt_gatt_service_unregister not clearing CCC information.
If the service is unregistered while an unbonded peer is connected and
subscribed then this CCC would be restored again when registering the
service even if the peer is now disconnected.
If the service is unregistered with bonded peers CCCs stored in settings
then this value would never be cleared. If the service is registered
again then the peer would receive a service changed for this service,
but it's CCC value would still be enabled.
Fixes: #26924
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Extract enqueue of GATT CCC when CONFIG_BT_SETTINGS_CCC_STORE_ON_WRITE
is enabled to a helper function gatt_ccc_conn_enqueue so that it can be
reused.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Move the clear_ccc_cfg function further up to be re-used without a
forward declaration in bt_gatt_service_unregister.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
va_list was initialized once and passed to log_backend_put_sync_string()
for each logging backend. State of such va_list was changed in each
execution, resulting in different va_list state to be passed for
consecutive log_backend_put_sync_string() calls. This results in
undefined behavior and program crashes.
Use va_copy() to copy va_list state to temporary variable for each
logging backend and keep original va_list untouched. Pass such temporary
state to log_backend_put_sync_string() to make sure state for all
consecutive calls does not change.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Instead of just showing network interface pointer, print also
network interface index. This helps debugging.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Starts the periodic heartbeat publish period at the end of the
publication, instead of at the ordering time. This ensures that the
heartbeat period doesn't get shortened by other enqueued messages.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
