Convert older DT_INST_ macro use in atmel sam0 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Added device tree nodes and associated headers for
defined uarts on the stm32g0 and stm32g07x 8x parts.
Tested with uart on stm32g071rb disco board with usart3 going to stlink.
Using shell.
Signed-off-by: Kieran Levin <ktl@frame.work>
Convert older DT_INST_ macro use in STM32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in esp32 drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Rename DT_INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 defines to something
non-DT prefixed. This way we know which defines are one's we generate
and which ones are driver created. It should be easy enough to replace
these INST_{0,1,2}_ESPRESSIF_ESP32_UART_IRQ_0 define with DTS generated
one macros once esp32 has interrupt controller support in DTS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in silab drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert older DT_INST_ macro use in stellaris drivers to the new
include/devicetree.h DT_INST macro APIs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add a dependency on the UART resource in the TI Power module,
reconfigure the UART upon CPU exiting standby, and add support
for device PM.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
The shared irq support isn't needed in this driver. We just need to
deal with the fact that some SoCs have only a single interrupt line and
some have three interrupts. We can just ifdef that based on
DT_NUM_IRQS.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
A txcnt of zero prevents transmission, as transmit requires the number
of entries in the transmit fifo to be strictly less than the txcnt
value. Set the default to 1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
uart_configure verification handler was missing what would cause a crash
if called from a user thread.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Added return -ENOTSUP in uart_rx_enable() if RX pin is disabled.
Fixed power management call where TASKRX was started even though
RX pin was disabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Extended nrf_uart driver to support TX only.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add a fixed clock to the qemu-virt-a53.dtsi to match how the musca dts
files work so we get the clock DT info in the same way in the driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
After RX is disabled during receiving, some bytes are received to
internal fifo. To not interfere with further transactions fifo has to be
flushed.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Convert driver to use DT_INST_ defines.
In the process, we've removed all UART/USART/LPUART code in
device instanciation code which had no impact.
Since all uart/usart/lpuart nodes declare compatibility with
st,stm32uart, DT_INST_X_ST_STM32_UART_FOO could be used.
Removed DT_UART fixup macros.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
In the DT_INST conversion we introduced a typo bug of accessing port0
instead of port1 in the IRQ config function.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update device data with the activated configuration, so that it
will be remembered for follow up configuration get requests.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The sole purpose of init options has been to enable hardware flow
control on NS16750 when asked. Use the proper DTS tags for this.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Added locking for TX transfers between async and polling API.
Added safety counters for checking if transmission finished.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add locking between async and polling tx transfers.
Add safety counters while waiting for transmission to finish.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Convert driver to fully use DT_INST_ defines. Currently IRQs are not
generated from DTS on esp32 so we create #defines for what they should
look like. Convert the IRQ defines to match DT_INST style so if/when
we have that info in DTS it will look the same.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update hal_nordic's revision, so that NRFX_ASSERT uses __ASSERT_NO_MSG
directly, not through the assert macro that comes from from libc,
as the definition of the latter might be different when some specific
libc version is used, and this could generate troubles.
Replace also uses of assert() with __ASSERT_NO_MSG() in nrfx driver
shims that use this macro without including the corresponding header
file (i.e. that implicitly rely on assert.h being included from
nrfx_glue.h, which is no longer the case).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return `1`.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The `irq_update` UART API function must always return 1 according to
the API documentations.
This commit fixes the `irq_update` API function to unconditionally
return '1'.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Since driver is shared with other devices, it must be enabled
conditionally based on the number of instances. This avoid show
invalid options for devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
SAMV71 uses same driver of SAME70 and this enables the feature. Since
driver is shared with other devices, it must be enabled conditionally
based on the number of instances. This avoid show invalid options for
devices with lower port count like SAM4S/SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit fixes the multiple SERCOM interrupt handling for the SAM
D5x and E5x devices by replacing the obsolete device tree symbol with
the new `DT_INST` symbol.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
When building with LLVM we get the following error:
uart_stm32.c:272:9: error: implicit conversion from enumeration type
'enum uart_config_parity' to different enumeration type
'enum uart_config_flow_control' [-Werror,-Wenum-conversion]
return UART_CFG_PARITY_NONE;
~~~~~~ ^~~~~~~~~~~~~~~~~~~~
We shouldn't be mixing parity and flow control enum's. Use
UART_CFG_FLOW_CTRL_NONE instead or UART_CFG_PARITY_NONE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current implementation directly passes timeout value to workqueue/timer
which results in assertion or instant timeout in case when K_FOREVER is
passed. This fix ensures that no timer or workqueue is called with
K_FOREVER.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Use signed values for timeout in UART asynchronous API, to be consistent
with timeout type in timer and workqueue values.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Extended nrf_uarte driver to support TX only UARTE instances.
When RX pin is not provided then RX is not started at all. This
allows to achieve low power with logging/console enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
