This commit allows let build zperf sample with overlay-netusb.conf.
USB subsystem must be enabled by the application.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Remove dependency on CONFIG_BT_ACL_FLOW_CONTROL and use
CONFIG_BT_L2CAP_RX_MTU always to set L2CAP RX MTU.
The ATT MTU is set from two different KConfig options depending
on if CONFIG_BT_ACL_FLOW_CONTROL is enabled, which makes it
a confusing option and hard to provide a conf file that
supports multiple board configurations.
This changes the behavior when CONFIG_BT_ACL_FLOW_CONTROL and
CONFIG_BT_BUF_RX_LEN was used to set the L2CAP RX MTU, and by
extension the ATT MTU.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
A proper way to match a Security object instance with a Server object
instance is via Short Server ID resource. Both coupled object instances
should carry the same value of this resource in order to me considered
matched.
This was not implemented in the LwM2M library and it was incorrectly
assumed that the Security object instance index corresponds to the
Server object instance index. While such apporach works is simple
scenario, it might yield incorrect results when bootstrap is used.
Fix this, by verifyng the Short Server ID resource in the Secuirty
instance used, and finding a matching Server instance. The server object
instance is stored for future use in the engine.
Additionally, remove an extra Server object instance that was created
when the bootstrap procedure was used. Since the boostrap Security
object instance does not have the corresponding Server object, it's
enough to have a single Server instance.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Zephyr introduced subsys/mgmt folder for MCU management. Move UpdateHub
sample to its correspondent folder at sample/subsys/mgmt folder.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
It was already using uart_irq_callback_user_data_set below, now it also
uses uart_irq_callback_user_data_t as callback type, so let's normalize
the callbacks.
Fixes#26923
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
TI CC32xx does not support binding the same port to multiple sockets,
but instead uses the IPv6 socket to handle both IPv4 and IPv6
connections. This commit modifies the sample to reflect this.
In addition, Kconfig options are overridden in order for the sample
to take advantage of wifi and socket offloading on this platform.
Signed-off-by: Vincent Wan <vwan@ti.com>
On TI CC32xx, the same port number cannot be bound to different
sockets. Instead, when an IPv6 socket is bound it can handle both IPv4
and IPv6 connections.
Signed-off-by: Vincent Wan <vwan@ti.com>
Fix compilation error when the DIAG module is enabled.
All core functionalities are provided.
Signed-off-by: Piotr Szkotak <piotr.szkotak@nordicsemi.no>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
After Zephyr 2.3.0 release system uses more RAM. This update
samr21_xpro configuration to allow echo_client be equal to
echo_server configs and remove unnecessary definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
After Zephyr 2.3.0 release system uses more RAM. This update
samr21_xpro configuration to allow echo_server run again and
remove unnecessary definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The sam4e_xpro and sam_v71_xult configs are unnecessary. Now
atmel_rf2xx shield will complement all necessary configuration.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The sam4s_xplained and sam_v71_xult configs are unnecessary. Now
atmel_rf2xx shield will complement all necessary configuration.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
extended download progress metrics to Bytes, KiB and MiB
separate number of download iterations for INF and numeric case
Signed-off-by: Alexander Kozhinov <AlexanderKozhinov@yandex.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Unit tests were failing to build because random header was included by
kernel_includes.h. The problem is that rand32.h includes a generated
file that is either not generated or not included when building unit
tests. Also, it is better to limit the scope of this file to where it is
used.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Some of the settings are no longer needed in the sample as OpenThread
configuration manages it by itself.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
Simplify overall scenario using sntp_simple to keep main MQTT logic more
clear. Also, remove related code which was used only by the old SNTP
code, e.g. show_addrinfo().
Signed-off-by: Alexey Markevich <buhhunyx@gmail.com>
Callback used mqtt_publish_qos1_ack but mqtt_subscribe called with
default 0 value (MQTT_QOS_0_AT_MOST_ONCE)
Signed-off-by: Alexey Markevich <buhhunyx@gmail.com>
New config file to build an OpenThread NCP for the NRF52840-DK
via CDC-ACM USB on the connector J3 (labelled 'nRF USB').
Signed-off-by: Markus Becker <markus.becker@tridonic.com>
zperf takes a potentially unaligned netowrk packet, casts it to a
struct, and then dereferences the fields. This causes a crash on
cores that don't support unaligned access such as the Cortex-M0+.
Use the UNALIGNED_GET helper instead.
Signed-off-by: Michael Hope <mlhx@google.com>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming multiple projects
"NONE" defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names, small, manual adjustments
have been done.
See also 7eabab2f5d ("samples, tests: Use semi-accurate project names")
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Move to using PRIu64/PRId64 instead of %llu/%lld since on
native_posix_64 the uint64_t/int64_t type is defined in terms of 'long
int' and not 'long long int'.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This provides a better error message when building with CMake and
forgetting ZEPHYR_BASE or not registering Zephyr in the CMake package
registry. See parent commit for more details (split from parent for
better readability).
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
Support for the socketpair(2) system call was recently
added for 2.3.0 .
This change adds a sample application that demonstrates
how it can be used.
Fixes#25527
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
If build with full POSIX API, use read()/write() instead of
recv()/send() calls for sockets.
We have read()/write() support for a while, but no samples/tests
actually performed at least a build test for it (so it will be
done now).
Fixes: #25407
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add missing sample.yaml file to enable CI build tests. Local tests can
be executed executing sanitycheck:
./scripts/sanitycheck -l --testcase-root samples/net/updatehub
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
The esp32 offload driver is used by shield esp_8266. This shield
doesn't have tests enabled to ensures that dependencies are ok.
This enables wifi sample to validate shield esp_8266 on CI and
consequently esp32 offload driver.
Fixes: #25386
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Make sure that we have proper network interface which support
VLAN and LLDP in this sample.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clarify in the docs the importance of generating a key type that matches
the configuration used to sign JWT tokens.
Signed-off-by: David Brown <david.brown@linaro.org>
