After running command --list-test-duplicates
I found out that some test cases have same names (duplicated).
To get rid of it, I decided to change names in .yaml files
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Replace Kconfig configuration data with devicetree bindings using
(ADC) io channels. Rework the sample to document expectations about
the relationship between the reference voltage and the divider input
voltage, and update the sensor configuration to support Nordic SAADC.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The test case no longer permits inferring input and output pins based
only on the presence of GPIO aliases. Stop allowing presence of GPIO
aliases to enable the test.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Fixes a timeout failure on the frdm_k64f board.
test_short_relative_alarm iterates 100x through a 3 tick loop, but some
platforms like frdm_k64f have a 1 second counter tick period and
therefore need more time to finish this test.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Successful execution of this test requires a board-specific overlay to
identify the test pins, and that the test pins be shorted together.
Document this requirement.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some boards don't support level interrupts; respect their rejection of
the configuration.
Also correct the code intended to disable the interrupt from within
the callback when level triggers are tested. Note that the legacy
call emulation does not work: it's necessary to add a flag that causes
the interrupt to be disabled.
Also improve a diagnostic and fix the exit path for a failure detected
before the callback was installed.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The Xilinx QEMU, used to emulate the Xilinx ZynqMP platform, is
particularly unstable in terms of timing.
This commit increases the tick margin for the Xilinx ZynqMP platform
from 1 to 5 in order to allow the sleep test to pass with a reasonable
repeatability.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit introduces the common tick margin definition that can be
used to specify the maximum allowable deviation from the expected
number of ticks.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The assert for error checking used the wrong variable.
data_buf was checked instead of the ret variable.
Fixes#22656
Coverity-CID: 208192
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
This test was whiteboxing the _current_cpu pointer to extract the CPU
ID. That's actually racy: the thread can be preempted and migrated to
another CPU between the _current_cpu expression and the read of the ID
field. Do it right.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Coverity believes that a field is null when it isn't. Duplicate the
assert from 20 lines up in hopes it learns better.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The existing stack_analyze APIs had some problems:
1. Not properly namespaced
2. Accepted the stack object as a parameter, yet the stack object
does not contain the necessary information to get the associated
buffer region, the thread object is needed for this
3. Caused a crash on certain platforms that do not allow inspection
of unused stack space for the currently running thread
4. No user mode access
5. Separately passed in thread name
We deprecate these functions and add a new API
k_thread_stack_space_get() which addresses all of these issues.
A helper API log_stack_usage() also added which resembles
STACK_ANALYZE() in functionality.
Fixes: #17852
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Interrupt routing on x86-64 is done entirely at runtime,
we should skip all 64-bit targets not just QEMU.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
A few test header files have C++ guards around them, but are incorrect.
Those files had a leading `#` placed before `extern`, which is
incorrect. This commit simply removes those leading `#` characters.
Signed-off-by: Brooks Prumo <brooks@prumo.org>
This makes simulate command advertise with proper UUID so the likes of
central_hr can connect to it when simulating:
hrs simulate on
Registering HRS Service
Connected: 00:aa:01:01:00:24 (public)
Start HRS simulation
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Added subsys argument to the callback, updated one driver which
used it and test cases.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Add privacy configuration when using the split controller for the test
basic_conn_encrypt. The handling with or without controller based
privacy affects the RPA handling in the host due to different
connection complete events being used. This affects the overall pairing
procedure as the addresses are inputs to the pairing functions.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Since the callback enable and disable functions are deprecated, but
cannot be re-implemented in terms of other API, add back an old-style
interrupt configuration test that uses the deprecated flags and
functions in the way existing code would do. The test module
internally disables the deprecation warnings.
Remove the test for the deprecated read/write functions, incorporating
a basic check into the module that tests deprecated callback functions.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new API and replace the enable/disable callback calls with pin
interrupt configuration instead.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use the new pin and interrupt configuration API.
NOTE: Because hardware is not available this has been build-tested
only.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add the common config structure as a prefix of the driver-specific
config structure and use the devicetree GPIO pin counts to initialize
it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Update the intel_s1000_crb test app:
() Update configuration calls to use new flags.
() Separate pin configuration into setting it to input, and
setting the pin for interrupt.
() Use gpio_pin_get/set() instead of gpio_pin_read/write().
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
IO extenders may provide input signals to LEDs or sensors where
leaving the signal undriven may result in increased power consumption
or misbehavior. The SX1509B powers up with all signals configured as
inputs. Provide a way to indicate which pins should be set as output,
and their initial signal level, when the device is configured.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Previously the check would fail if a higher pin was present in the
callback set. Callbacks should only be told about pins that are
relevant to the callback, so reject unless exactly the expected pin
was provided.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Exclude the mps2_an385/mps2_an521 as we try to run on qemu and that
doesnt support the GPIO/LED so the tests will fail. For now exclude
the platform completely until we can just do a sim run exclusion.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
- Updates gpio driver and device tree files to the new GPIO Config flags
- Implements the new port_* APIs
- Update I2C and PWM Drivers to use new GPIO config
- Add esp32.overlay to gpio_basic_api test
- refactor convert_int_type, regs struct
- remove config_polarity
- add kConfig notes
Tests:
- samples/basic/blinky
- samples/basic/button
- tests/drivers/gpio/gpio_basic_api
- tests/drivers/gpio/gpio_api_1pin
Board:
- esp32 DevKitC V4
Note about interrupts:
The ESP32 requires specifying a CPU interrupt to be used for GPIO
interrupt signals. CPU interrupts can be either level or edge (or
special) triggered, but not both.
Please check gpio/Kconfig.esp32 for more info.
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
Enables the 2-pin gpio test on the rv32m1_vega_ri5cy board by adding a
dts overlay and configuring pinmuxes on the arduino header.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
When checking the behavior of pull configurations delay long enough
for the signal to stabilize. Checking without a sufficient delay may
indicate a false failure.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The debounce flag is to be provided to the pin configuration, not the
pin interrupt configuration.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
Pins enabled to be used as GPIO for 2 pin test gpio_basic_api.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
LPC54114 to use D0 and D1 pinout.
LPC55S69 to use A0 and A1 pinout.
2 pin test gpio_basic_api uses pins set up in boars' pinmux.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
