Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Error codes from DSPI_MasterTransferNonBlocking are now handled in
tranceive to ensure that the context is unlocked when an busy bus
is detected.
Signed-off-by: Mikkel Jakobsen <mikkel.aunsbjerg@prevas.dk>
The current sam spi driver uses soc dependent name which duplicate
configuration to enable other platforms. This refactor current
definitions to a generic way to reuse symbols by multi soc definitions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
spi_context_lock() & spi_context_release() are called in transceive()
function for a better readability.
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Create new instances of SPI using single STM32_SPI_INIT() macro
invocation, similar as it is done for STM32 UART driver. Add also
implicit '#ifdef CONFIG_SPI_id' check, so it further reduces required
lines of code for each SPI instance definition.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Refactors the mcux dspi driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Need to set device busy when enter into transceive function
in SPI DW driver.
In current SPI DW driver the transceive function don't set busy state,
but that is important for PM busy state.
This will lead to unexpected behaviors when system calls this
function and enter into idle state.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced SPI_MCUX_FLEXCOMM
symbol.
Also clean up the header to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The SPI SERCOM peripheral found on the SAMD5x/SAME5x is very much alike
the one found in previous SAM0 MCUs.
Only the clock setup is different.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
If possible, allow sending 16bits at once instead of 8bits. I found
large delays (up to 3us) between sending bytes due to Zephyr SPI
overhead, so allowing 16bits at a time if possible helps save that
time.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
Cleanup around COND_CODE_1 usage and replacing with
IF_ENABLED if applicable.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr spi interface. It leverages heavily from the existing mcux dspi
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
After switching to nrfx 2.0.0, the Kconfig choice options that allowed
enabling of pull-up or pull-down for MISO lines in SPIs and SPIMs are
not properly supported, they are simply ignored. This commit restores
the possibility of applying pull configuration for MISO lines.
In earlier nrfx versions, the MISO pull configuration could be only
set globally, in nrfx_config files, for all SPI and SPIM instances
together. Since nrfx 2.0.0, this configuration can be applied per
instance. This commit takes advantage of this possibility and instead
of using a common Kconfig option as a global setting for all instances,
allows applying individual instance settings via devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This is a follow-up to commit 84f8235005.
Default initialization to 0 of the .dcx_pin field in the extended part
of the SPIM configuration is incorrect, because this means that pin 0
should be used as the D/CX line. For the SPIM instance that provides
the extended functionality, this results in undesired assignment of
the pin 0, and for the other SPIM instances, this causes that their
initialization fails with the NRFX_ERROR_NOT_SUPPORTED code.
This commit sets this field to NRFX_SPIM_PIN_NOT_USED, to indicate that
the D/CX line is not supposed to be used.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Fill the `rx_delay` field in the SPIM configuration structure only when
the RXDELAY feature is present in a given SPIM instance, to prevent
compilation errors when some other SPIM instance is enabled together
with SPIM3.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
When pass NULL to spi_transceive with user space enabled, stack buffer
is still passed to spi driver and it will cause kinds of problems like
MPU fault, so change it to pass relevant NULL pointers in the actual
transceive call.
Fixes: #20811.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
This patch tests the return code when calling clock_control_get_rate
and completes the issue #20503 seen on watchdog
[Coverity CID :205655]
Fixes#20503
Signed-off-by: Francois Ramu <francois.ramu@st.com>
By adding new SoC to Zephyr drivers has to be updated.
Commit affects:
- USB driver
- support for nRF52833 added.
- support for USB_DEVICE_REMOTE_WAKEUP in hid-mouse added.
- SPI
- IEEE 802.15.4
- CLOCK CONTROL
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Update calls to nrfx HAL functions to reflect API changes introduced in
nrfx 2.0.0. All these functions are now called with the first parameter
pointing to the structure of registers of the relevant peripheral.
Also a few functions got renamed:
- nrf_gpiote_int_is_enabled to nrf_gpiote_int_enable_check
- nrf_gpiote_event_is_set to nrf_gpiote_event_check
- nrf_rng_event_get to nrf_rng_event_check
- nrf_rng_int_get to nrf_rng_int_enable_check
- nrf_rtc_event_pending to nrf_rtc_event_check
- nrf_rtc_int_is_enabled to nrf_rtc_int_enable_check
- nrf_timer_cc_read to nrf_timer_cc_get
- nrf_timer_cc_write to nrf_timer_cc_set
Default configuration values were removed from nrfx_config files,
so the drivers pwm_nrfx and spi_nrfx_spis no longer can use those.
Function nrfx_pwm_init() now takes one more parameter - context pointer
that is passed to the event handler, not used in the pwm_nrfx driver.
HALs for UART and UARTE now allow configuration of the parity type
and the number of stop bits, for SoCs that provide the corresponding
registers.
Signed-off-by: Karol Lasończyk <karol.lasonczyk@nordicsemi.no>
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The SPI peripheral should be configured using the CPU clock speed and
not the system clock speed. This used to be fine because they were the
same before #19232, but now that the system clock is RTC-based (which
has a different frequency), we can no longer make that assumption.
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Add SPI driver and bindings for LPSPI peripheral for the RV32M1 SOC.
Based heavily on the existing mcux LPSPI driver.
Signed-off-by: Karsten Koenig <karsten.koenig.030@gmail.com>
Same deal as in commit 677f1e6db9 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for some newly introduced (or maybe
overlooked) stuff.
Also clean up formatting a bit, replacing spaces with tabs and
shortening the header.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Defining a symbol with 'menuconfig' just tells the menuconfig to display
any dependent symbols that immediately follow it in a separate menu.
'menuconfig' has no effect on symbol values.
Making a symbol that doesn't have any dependent symbols after it a
'menuconfig' should be avoided, because then you end up with an empty
menu, which is shown as e.g.
[*] Enable foo ---
This is how it would be shown if there were children but they all
happened to be invisible as well.
With a regular 'config', it turns into
[*] Enable foo
Change all pointless 'menuconfig's to 'config's.
See the section on 'menuconfig' on the Kconfig - Tips and Best Practices
page as well.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This commit adds LiteX SPI drivers and its bindings.
Signed-off-by: Daniel Craviee <dcraviee@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
This commit introduces separate "compatible" strings for DTS nodes
representing different types of Nordic SPI peripherals. Previously
"nordic,nrf-spi" was used for both SPI and SPIM. SPIS was already
handled separately.
Quite a few files need to be touched by this commit but the changes can
be divided into groups of related or very similar ones, distinguishable
by the initial part of the path to the modified file:
* dts/bindings/spi/
new binding for "nordic,nrf-spim" is added and common fields for all
3 types of Nordic SPI peripherals are extracted to a shared file
* dts/arm/nordic/
"compatible" properties in spiX nodes are updated (when there is no
choice as only one type of SPI peripheral is available) or replaced
with a comment pointing out that the proper type of peripheral needs
to be picked at some upper layer
* drivers/spi/
spi_nrfx_spim driver is updated with the new form of macros generated
from dts
* boards/
all spiX nodes in dts files for boards equipped with an nRF chip are
updated with the proper "compatible" property, according to the type
of SPI peripheral that is currently selected for the board by the
corresponding Kconfig choice option (SPI_x_NRF_SPI*)
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In some hardware, e.g. ARC HS Development kit,the peripheral
space of DesignWare SPI only allowes WORD access,
byte acess will raise bus error.
This commit adds support for this case
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
These calls are not accessible in CI test, nor do they get built on
common platforms (in at least one case I found a typo which proved the
code was truly unused). These changes are blind, so live in a
separate commit. But the nature of the port is mechanical, all other
syscalls in the system work fine, and any errors should be easily
corrected.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Use a consistent way of enabling particular instances of peripherals
in nrfx drivers through options defined in modules/Kconfig.nordic,
to make the usage of nrfx drivers in Zephyr, especially the ones for
which there are no Zephyr driver shims (yet), easier.
Jira: NCSDK-2744
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This was only used on Quark SoCs. It is no longer used, can no
longer be tested, and it's reliant upon the deprecated legacy PCI
subsystem. Remove it to prevent bitrot.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Consistently place C++ use of extern "C" after all include directives,
within the negative branch of _ASMLANGUAGE if used.
Only updated in headers that already had support for drivers built with
a C++ compiler.
The spi_dw.h file defines macros to declare functions, then uses them
within a file that may have out-of-tree overrides. In this case we
leave the including file extern "C" active for backward compatibility.
Background from issue #17997:
Declarations that use C linkage should be placed within extern "C"
so the language linkage is correct when the header is included by
a C++ compiler.
Similarly #include directives should be outside the extern "C" to
ensure the language-specific default linkage is applied to any
declarations provided by the included header.
See: https://en.cppreference.com/w/cpp/language/language_linkage
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Abstract some SPI LL function call for future driver compatibility with
a new SPI peripheral version (introduced with STM32MP1x and STM32H7x
SoC)
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This commit solves an issue where the NSS must be set before the
mode on the stm32mp157c_dk2, else LL_SPI_SetMode won't affect the
mode registry.
stm32mp1x (and stm32h7) LL function SPI_Init seems to also define
first the NSS then the mode, unlike other STM32 boards where this
is not specified.
Changing the order shouldn't have bad repercussions on other boards,
ZephyrnSPI driver test has been passed successfully on disco_l475_iot1
board.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Split a long line remaining in the driver.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
Allow the user to use software slave select instead of the
hardware pin, in order to free the related GPIO and avoid
unwanted SS triggering on the hardware pin. The default SS
is still the hardware pin.
Signed-off-by: Yaël Boutreux <yael.boutreux@st.com>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@st.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The spi_dw driver used system clock frequency
as a base for SPI bus frequency calculation.
This commit corrects that by obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move dma.h to drivers/dma.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The defines should have had a _0 on them, now that we generate the
proper defines, fixup the cases that used that old scheme.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Per guidelines, all statements should have braces around them. We do not
have a CI check for this, so a few went in unnoticed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
When some header are included into C++ source file, this kind of
compilations errors are generated:
error: invalid conversion from 'void*'
to 'u32_t*' {aka 'unsigned int*'} [-fpermissive]
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Move SERCOM peripherals to use the raw defines generated from DTS
parsing. This adds aliases to the DTS so that the SERCOM number
can still be used for clocking and pinmux.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the async API for SAM0 SERCOM SPI using
DMA to drive the device. This implementation does the reload
for both transmit and receive in the receive DMA handler.
Doing this simplifies the implementation but means that the
transmit drains completely, resulting in the SPI clock pausing
between buffers while both are reloaded in the receive handler.
Tested with tests/drivers/spi/spi_loopback and several simple
programs monitored with a logic analyzer.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add a Kconfig option to enable DMA for SPI with SOC_NRF52832 as long as
it being disabled due to Product Anomaly Notice (PAN) 58 is explicitly
overridden. This allows the SPIM driver to be enabled for the nRF52832
SoC for situations where PAN 58 is not a problem.
Signed-off-by: Andrew Fernandes <andrew@fernandes.org>
Make sure that when e.g. CONFIG_SERIAL is set, CONFIG_UART_SAM0 is
selected automatically when the sam0 SoC family is used.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Asyc transceive is currently not implemented for this driver,
so don't claim support.
spi_context_lock() is already being called in spi_sam_transceive()
so calling it in the wrapper function will cause a deadlock.
This reverts eae05d928e
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
The existing device_set_power_state() API works only in synchronous
mode and this is not desirable for devices(ex: Gyro) which take
longer time (few 100 mSec) to suspend/resume.
To support async mode, a new callback argument is added to the API.
The device drivers can asynchronously suspend/resume and call the
callback function upon completion of the async request.
This commit adds the missing callback parameter to all the drivers
to make it compliant with the new API.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Maybe this is some "just in case" thing that got copied around. There's
no need to have a blank line at the beginning or end of Kconfig files.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The two redundant SPI dependencies are from 'source'ing a file within an
'if SPI' and then adding another 'depends on SPI' within it.
'if FOO' is just shorthand for adding depends on FOO to each item within
the 'if'. There are no "conditional includes" in Kconfig, so 'if FOO'
has no special meaning around a source. Conditional includes wouldn't be
possible, because an if condition could include (directly or indirectly)
forward references to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Rephrase prompts for a few options in drivers/spi/Kconfig.nrfx
so that their purpose is presented a bit better.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
In Nordic SoCs, SPI and TWI peripherals with the same instance number
share certain resources and therefore cannot be used at the same time
(in nRF91 Series this limitation concerns UART peripherals as well).
This patch adds Kconfig checks ensuring that only one of such mutually
exclusive peripherals can be enabled.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This patch adds missing SPI_3_NRF_SPIS Kconfig option (referenced by
`ext/hal/nordic/nrfx_config_nrf9160.h`, although not defined anywhere)
and adds support for SPIS3 instance in the nrfx_spis driver shim.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Coverity scan found issue with a missing 'break' statement. Fix
push_data by adding the break after handling the 1 byte case.
Coverity CID: 190978
Fixes#13842
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
The spi mcux_lpspi driver has been using non DT_ prefixed defines for
DT generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Instance 2 & 3 for some reason never transitioned CONFIG_SPI_*_IRQ_* to
DT prefix. Fix that since those Kconfig symbols will never exist.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add SPI_6 Kconfig symbol as this is the higher supported instance on
STM32.
This makes symbol CONFIG_SPI_6, used in stm32 driver a valid symbol.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use separate bindings for nRF Family SPI Slaves and SPI Masters so that
the properties "csn" and "def-char" can be made required for Slaves
(for Masters such settings are not applicable), and to avoid confusion
between the properties "csn" and "cs-gpios" for Master nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The driver was defining a macro with a CONFIG_ prefix but this wasn't
coming from Kconfig. Change the macro name not to conflict with the
Kconfig CONFIG_ namespace.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
initialize both tx and rx in the spi_sam0 driver. Make the spi_sam
driver look the same by splitting the declaration into 2 lines.
Discovered with gcc 8.2
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Make the following nRF peripheral drivers:
- ADC
- GPIO
- I2C
- SPI
- UART
- USB_DEVICE
enabled by default so that users do not need to explicitly enable them
in their applications after choosing an nRF SoC as the build target.
Kconfig options enabling these drivers depend on both a given hardware
feature (e.g. I2C) and an nRF family SoC selected, so effectively they
will be automatically enabled only when it is adequate (and in most
cases these drivers are the only option for a given hardware feature
on nRF SoCs).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Check clock_control_on return value now that it is checking appropriate
bus is used in the request.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When users are configuring applications they are given the option
to enable the DesignWare SPI driver. But they should not be given this
option on SoCs that don't have the DesignWare SPI HW.
This commit hides the driver by default by introducing the config
option HAS_SPI_DW.
Fixes: #10825
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If the configuration is already installed, there will no need to
reconfigure the controller all over again.
This was missing for mcux_dspi, mcux_lspi, sam and sam0.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
All drivers require DTS for their primary SPI settings.
Removing SPI_[0-9]_NAME config option added some more samples changes.
Usage of these options there was anyway not relevant.
Fixes#11064
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In order to avoid changing the signature of spi_context_cs_control
function, which is used in every driver, let's just make it an alias to
a new version.
Fixes#10344
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move to using Kconfig (like other Atmel SAM drivers do) to specify the
pinmux setting for SAMe70 SoCs. Updated the sam_e70_xplained board to
set the default in Kconfig.defconfig instead of via board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
k_poll_signal was being used by both, struct and function. Besides
this being extremely error prone it is also a MISRA-C violation.
Changing the function to contain a verb, since it performs an action
and the struct will be a noun. This pattern must be formalized and
followed and across the project.
MISRA-C rules 5.7 and 5.9
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Configure spi chip select based on pinmap defines, add support
for hardware chip select control support.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Following log subsystem rework, a warning poped-up in SYS_LOG_ERR
in spi_stm32_get_err macro.
Fix it by casting SPI_STM32_ERR_MSK on (u32_t)
Fixes#10380
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Under GNU C, sizeof(void) = 1. This commit merely makes it explicit u8.
Pointer arithmetics over void types is:
* A GNU C extension
* Not supported by Clang
* Illegal across all ISO C standards
See also: https://gcc.gnu.org/onlinedocs/gcc/Pointer-Arith.html
Signed-off-by: Mark Ruvald Pedersen <mped@oticon.com>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Introduces a new mcux lpspi shim driver to be used on the imxrt soc.
This shim driver leverages heavily from the mcux dspi shim driver
because the MCUXpresso SDK provides similar APIs for the lpspi and dspi
peripherals.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
These mcux dspi driver configs are no longer used after legacy API
support was removed in commit 09dd5e9b22.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
