Remove magic numbers from Ethernet drivers and tests by defining
NET_ETH_MAX_DATAGRAM_SIZE and NET_ETH_MAX_FRAME_SIZE.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If we receive the ARP request, then check if the ARP cache
contains an entry for this IP address already. If it does,
then update the MAC address in the cache.
Fixes#10188
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
No need to hide the symbols in the header file if CONFIG_NET_LLDP
is not enabled. This also allows the documentation to be generated
properly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure that network related functions are always documented.
This means keeping the prototype and possible stub together.
Fixes#12615
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add ETH_P_xxx protocol types if they are missing. After this
we can use the protocol types when working with BSD sockets.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Current code generating Ethernet header is scattered all over the place,
sometimes in functions that are supposed to check something (and not
filling the header). Not to say about innefficiency.
Src ll address does not need to be set in L2 as net_if.c handles that
already.
Broadcast dst ll address is the same in ipv4 or ipv6, thus factorizing.
In each case, multicast is filled in only at the relevant place.
This is the first step towards changing L2 sending logic, when L2 send
API function will be the only point of sending. The redirection from
driver to L2 again (which finally uses the right device API function to
send) it a temporary hack.
This simplifies the code but will also enable using statically
allocated net_buf and ethernet header payload buffer afterwards.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is currently unoptimized, as all frags are allocated with relevant
ll reserve for such header space. However, this is the first step
towards getting rid of that ll reserve concept everywhere.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add RX API to LLDP. Caller should register callback which is called
from ethernet_recv().
Fixes#9407
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
If the driver has created start() and stop() functions, then those
are called when ethernet L2 is enabled or disabled.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The LLDP protocol defines 2 separate agents, the Transmitters and
the Receivers. For the context of Zephyr, we are only interested in
the Tx agent, thus we drop any LLDP frames received by Zephyr.
LLDP frames are basically composed by an ethernet header followed by
the LLDP Protocol Data Unit (LLDPDU). The LLDPDU is composed by several
TLVs, some of them being mandatory and some optional.
Our approach here is having TLVs fully configured from Kconfig, thus
having the entire LLDPDU constructed on build time.
The commit adds NET_ETH_PTYPE_LLDP definition and related handling.
If CONFIG_NET_LLDP is enabled then ethernet_context has a pointer to
the struct net_lldpdu that belongs to that ethernet interface. Also
when CONFIG_NET_LLDP is enabled, the LLDP state machine will start to
send packets when network interface is coming up.
Currently the LLDP state machine is just a k_delayed_work() sending the
LLDPDU at a given period (defined by CONFIG_NET_LLDP_TX_INTERVAL).
Fixes#3233
Signed-off-by: Jesus Sanchez-Palencia <jesus.sanchez-palencia@intel.com>
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This are all the parameters defined by the standard (12.21.1).
Additionally the parameters that are read-only are validated in the
ethernet_set_config callback.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
There are too many individual requests for Qav related parameters. There
are more Qav parameters that need to be supported (and will be supported
soon - both on the GET and SET side). Handling it the way it was handled
so far would render the eth mgmt API dominated by Qav parameters. That
would make the file hard to read and understand.
Instead of that - use a single GET and SET requests for all Qav
parameters. This works by adding a separate enum with Qav request type
to the ethernet_qav_param struct.
Additionally this approach makes it much easier to document it all since
we now have just a single request and documentation comments in the
ethernet_qav_param struct.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Add calls responsible for getting and setting on/off status of Qav on
capable priority queues.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Some Ethernet devices can filter out incoming packets through a list of
valid MAC addresses, so let's add a way to expose this capability, using
it through the ethernet device API.
Fixes#7596
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This makes use of the get_config callback added to the Ethernet API.
For now the only parameter to get is the number of available priority
queues.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This callback will be used to get HW specific configuration that cannot
be accessed through L2 directly.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The advantage to this approach allows drivers for
devices that already keep statistics data on hardware
registers to use those instead, rather than try to
replicate it the same counters again within the driver
itself.
The eth_native_posix.c driver though do not benefit
from this, is modified to use the new callback system.
Suggested-by: Jukka Rissanen <jukka.rissanen@intel.com>
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
This commit adds a possibility to use Qav (credit-based shaping) in the
ethernet drivers.
There are two parameters exposed through the mgmt api: deltaBandwidth
and idleSlope.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
A small helper function will return information whether
a given network interface has VLAN enabled or not.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Defines a PTP clock driver that can be implemented in those network
interface drivers that provide gPTP support.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Julien Chevrier <julien.chevrier@intel.com>
Ethernet header is always filled in the first fragment of a packet,
so passing it as a separate function paramter is supefluous.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Add net_eth_carrier_on() and net_eth_carrier_off() functions that
can be called by ethernet device driver when it detects that carrier
is lost or found.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Make sure we are able to collect ethernet statistics and query
it via net management API.
Fixes#6899
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Depending on what's supported by the device, it could be possible to
configure these at runtime such as auto-negociation, link speed, etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Function should be exposed if only vlan is enabled.
Also, changing vlan_setup's signature to stay consistent with device
driver API.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Curently only link speed is exposed.
Opportunity taken to remove any post-fix enumerating the iface init
and/or the api: these must be generic and used by all the instances.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This allows creation of virtual lan (VLAN) networks. VLAN support is
only available for ethernet network technology.
Fixes#3234
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
__packed allows the struct to be linked at a non-word size boundrary
which causes an unaligned access fault on the Cortex-M0+.
Signed-off-by: Michael Hope <mlhx@google.com>
Create infrastructure that allows ethernet device driver to tell
if it supports network packet checksum offloading. This applies only
to IPv4, UDP or TCP checksums. The driver can enable/disable checksum
offloading separately for Tx and Rx network packets.
If the device (ethernet in this case) can calculate the network
packet checksum for IPv4, UDP or TCP, then do not calculate the
corresponding checksum by the stack itself.
Fixes#2987
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
IPv6 mcast addr to MAC mcast conversion was factored out to
subsys/net/ip/l2/ethernet.c for reuse by other drivers.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Make sure the multicast MAC address checker checks also
IPv4 multicast MAC address and accepts it.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of the networking header files in include/net/ directory were
missing @defgroup doxygen directives.
There was also duplicate @defgroup directives which are now changed
to @addtogroup directives.
Added also missing API links to doc/api/networking.rst file.
Added exceptions to .known-issues/doc/networking.conf file so that
doxygen does not complain.
Jira: ZEP-2308
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
