Update the hal_nordic module revision, to switch to nrfx 2.1.0.
Because the list of peripherals for nRF5340 has changed as follows:
- SPIM2 has been renamed to SPIM4
- SPIM2-3, SPIS2-3, TWIM2-3, TWIS2-3, and UARTE2-3 have been added
a couple of related corrections needed to be applied in dts and Kconfig
files, plus the spi_nrfx_spim driver has been extended with the support
for SPIM4.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The rf2xx driver is doing automatic retransmissions in hardware based
on whether ACKs are received or not. Currently the driver is not
invoking ieee802154_radio_handle_ack() as other drivers are doing and
required by OpenThread since 4fe1da9. This add rf2xx_handle_ack method
to ensures required ACK processing when driver performs TX.
Fixes: #21763
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Lots of style mess in this driver:
- 80 chars limit not followed
- variable allocation and if condition on it should be coalesced
- etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DesignWare driver can manage different amount of irqs so let's make it
configurable via DTS.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Base address does not change at runtime, thus storing it directly into
device's config.
Also keeping it consistent in naming: s/port/dev
And no need to store irq_num as it is unused.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There will be more instance of that driver, and the initialization
function will the same all the time. That was done wrong as it was not
following the device driver rules.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This driver is going to be used by other SoCs and as such should be
easily configurable through DTS.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
irq_enable() can be directly called from relevant irq config function
and thus voids the necessity to store the IRQ number, saving some
memory.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There is no such thing as CAVS DMA IP block, the DMA IP block found on
CAVS based chips is made with DesignWare one.
This will help to centralize DW based DMA device into one driver.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The sx1276_rx_done() function supports RSSI and SNR.
Change to support RSSI and SNR through sx1276_lora_recv() function.
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
The RF2XX driver not always sent ACK when a RX frame requests. This
happen because RF2XX transceiver asserts TRX_END interrupt after
confirm that the FCS is valid. The driver can now decode the frame
but in parallel the radio still processing the ACK frame. This will
sync the radio FSM state to ensure that ACK will be send.
Fixes#21659
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Remove soc/arm/st_stm32/stm32YY/flash_registers.h files.
Change register accesses in stm32 flash drivers to use FLASH_TypeDef
from modules/hal/stm32/stm32cube/stm32YYxx/soc/stm32xxxxxx.h.
Fixes#16235
Signed-off-by: Sarvesh Patkar <psarvesh314@gmail.com>
usb-device.h must be included only if CONFIG_USB_UART_CONSOLE is
defined, otherwise it is not used and will pull a lot of usb code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
when DMA IP is enabled on stm32 series,
the heap size must be configured to large value
because of dma channels configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This patches defines constants from dma registers
depending on the dma configuration of the stm32 soc
Some devices have 6 or 7 or 8 dma channels per dma instance
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This checks if the DMA controller supports or not
the memory-to-memory transfers. For DMA Version1,
in the stm32f2xx, stm32f4xx, stm32f7xx series,
only DMA instance 2 is able to transfer mem-to-mem.
For other series, with DMA Version2, there is no such a limitation.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Fix#22188
Introduce config option to disable automatic acknowledge via
virtual wires on response to eSPI host suspend and reset warnings.
This will give the opportunity for eSPI slave systems that need to
perform preparations before reset or suspend.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Introduce a new counter API function for reading the current counter
value (counter_get_value()) and deprecate the former counter_read() in
favor of this.
Update all drivers and calling code to match the new counter API.
The previous counter driver API function for reading the current value
of the counter (counter_read()) did not support indicating whether the
read suceeded. This is fine for counters internal to the SoC where the
read always succeeds but insufficient for external counters (e.g. I2C
or SPI slaves).
Fixes#21846.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
So far, nRF 802.15.4 radio driver build was dependent on the 802.15.4
subsystem in Zephyr. While this was a reasonable approach for samples,
it prevented the radio driver from being built as a standalone entity,
which could be useful in some applications (e. g. running core nRF
802.15.4 radio driver tests with Zephyr).
Resolve this, by providing a separate set of Kconfigs for the radio
driver, therefore allowing to build it as a separate entity. The 802154
subsystem simply enables the radio driver module in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Implement uart_pipe functionality for the modem so that it
integrates with the PPP implementation.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
Create a driver for GSM modems that use a standard AT command set
and enable Zephyr's own PPP stack for IP traffic.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
This commit introduces the can-primary alias to identify
the primary CAN interface.
This alias is used for all samples and tests, so they don't
need to probe the right interface.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The build infrastructure should not be adding the drivers subdirectory
to the include path. Fix the legacy uses that depended on that
addition.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The CONFIG_ prefixes were missing on these.
Found with a work-in-progress scripts/kconfig/lint.py check.
This symbol is defined in kernel/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
I2C interrupts usage should be the preferred way. This commit
enables them by default in the STM32 I2C driver itself.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Same deal as in commit 677f1e6 ("config: Turn pointless/confusing
'menuconfig's into 'config's"), for a newly-introduced stuff.
Also clean up headers to be consistent with recent cleanups.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
CONSOLE_HANDLER was unconditionally selecting UART_INTERRUPT_DRIVEN (and
depends on it in the code), but UART_INTERRUPT_DRIVEN depends on
SERIAL && SERIAL_SUPPORT_INTERRUPT.
Add a SERIAL_SUPPORT_INTERRUPT dependency to CONSOLE_HANDLER.
CONSOLE_HANDLER already depends on UART_CONSOLE, which depends on
SERIAL, so a SERIAL dependency does not need to be added.
This avoids some selects with unsatisfied dependencies in CI.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Silicon Labs EFM32GG11B SoCs have more USART ports than
currently supported by the driver. Driver expanded with
support for USART4 and USART5.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Ethernet MAC present in Silicon Labs EFM32GG11B4xx and
EFM32GG11B8xx SoCs.
DMA based driver with support for link up/down detection.
Signed-off-by: Oane Kingma <o.kingma@interay.com>
Define a binding for the Bosch BMA280 sensor. Remove the Kconfig
settings and update the driver to use the devicetree information.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
After startup the native_posix flash was filed by 0x00 instead
of 0xff, which is not coherent with erased byte value which
is 0xff for the native_posix target.
Such inconsistent behavior makes for instance running
a storage system designed(or configured) for a flash device
with 0xff as erased byte values problematic.
This patch makes flash erased after new flash device file creation.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The PrimeCell UART (PL011) IP can use one single combined/shared
interrupt line instead than different IRQ lines for TX/RX/Err/... This
is the most common configuration supported in the Linux world but not
currently supported in Zephyr. QEMU emulates a PL011 UART with a single
interrupt line as well.
To support this configuration we have to hookup the PL011 driver with a
shared IRQ driver and add two new configuration options when the shared
IRQ line is used.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
There is only one possible command, so just use if instead of switch
to avoid several MISRA-C violations and also avoid set dev_data wrongly
unused when UART_NS16550_DLF_ENABLED is defined.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Commit 68a235932f changed this driver to
not use hard-coded options. The problem was that these options were
never being set. This commit just set an initial value that can be
changed later.
Fix 68a235932f
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The NS16550 UART driver is currently hard-coded as 8-n-1
with no flow control. The baud rate is set by what is in DTS.
This commit moves away from hard-coded and strictly DTS to
configurable using the UART configure API. Requires commit #bcb807.
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
The UART configure API was added to uart.h and this commit
implements the initial framework for the configure API for
the ns16550 uart. This includes the configure() and config_get()
functions and uart device configuration structures of the uart
configure API for the ns16550.
Note this commit does not resolve the pre-existing hard-coded
8-n-1 implementation.
Signed-off-by: Jennifer Williams <jennifer.m.williams@intel.com>
Patch introduce references to LittleFS instead of NFFS where it
was suitable. In other places NFFS mentions were removed
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
According to NRF product specifications the smallest write unit is
32-bits. Added parameter 'CONFIG_EMULATE_ONE_BYTE_WRITE_ACCESS'
which allows one byte flash write using more complex operation.
Signed-off-by: Adam Kondraciuk <adam.kondraciuk@nordicsemi.no>
Grouped all nRF driver sub-option under SOC_FLASH_NRF
menuconfig.
This makes menuconfig cleaner.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Create new instances of SPI using single STM32_SPI_INIT() macro
invocation, similar as it is done for STM32 UART driver. Add also
implicit '#ifdef CONFIG_SPI_id' check, so it further reduces required
lines of code for each SPI instance definition.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Update the NXP Kinetis FlexCAN driver to use the initialization
parameters for disabling self-reception and enabling listen-only mode
added in MCUXpresso v2.7.0.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
...instead of kconfig.
This provides a bit more flexibility in defining driver
instances. Also, since the DTS defines 5 I2C controllers,
the driver code is extended to cover all 5 if the controllers
are enabled.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
The SoC, driver, and board support for the CC2650 and CC2650 Sensortag
aren't currently supported and we are removing them as such. If anyone
is interesting in supporting this platform we can easily recovery it
from git.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
These were unintentionally omitted. We don't expose callback
registration or callback response APIs for security reasons.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Ensure that the SPI SCK and MOSI pins are set to very high as slower
SPI speeds will cause device hangs when used. This is due to the state
changing too fast for hardware, causing RXE to never fire and thus
hang.
Signed-off-by: Pushpal Sidhu <psidhu.devel@gmail.com>
TCP segment with several EOL TCP options causes echo server to block and
use 100% of CPU. This patch fixes that issue by using k_yield to let
also other threads to run.
Fixes#21949
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
The path to include/drivers should not be in the compiler include path
list, only include/. In order to make this possible, always explictly
refer to hci_driver.h via the drivers/bluetooth/ path and not only
bluetooth/.
Fixes#21974.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Add sensor driver for the internal temperature sensor present in the
NXP Kinetis SoC series.
The driver allows reading the die temperature and the voltage of the
external voltage reference used for calculating the temperature.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Add support for `CAP_NO_IV_PREFIX` in mbedTLS_shim and advertise this as
one of its capabilities. When this flag is active, the IV passed is
preserved to allow applications to reuse the IV buffer.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Following update of STM32Cube packages for series F0/L0/F3,
a new file ll_usb.h is now available for these series.
As a consequence, specific hanlding is no more requested for this
series is stm32 usb_device driver.
Fixes#21962
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Invalid channel should be filtered in intmux isr, please refer to
page 1243~1244 of chapter 36 INTMUX of RV32M1 RM.
Note: Unlike the NVIC, the INTMUX does not latch pending source
interrupts. This means that the INTMUX output channel ISRs must
check for and handle a 0 value of the CHn_VEC register to account
for spurious interrupts.
Signed-off-by: Lyle Zhu <lyle.zhu@nxp.com>
Nrfx_uarte uses a hardware timer/counter to count received bytes.
Keeping this timer enabled increases power consumption for some SoCs.
This change disables the timer when an inactive power state is set.
Signed-off-by: Audun Korneliussen <audun.korneliussen@nordicsemi.no>
Refactors the mcux wdog driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux rtc driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux dspi driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpsci driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux uart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following update of stm32wb package, FLASH_FLAG_SR_ERROR
has been renamed to FLASH_FLAG_SR_ERRORS.
Update driver to fix compilation issue.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The firmware version on the CCS811 on nrf52_pca20020 is generally
version 1.1, which does not set the data ready bit in the status
register. Assume that a non-zero CO2 measurement on that version is
fresh for the purposes of determining the fetch status.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The application may want to know the configured mode without inspecting
Kconfig macros; this is important for proper management of BASELINE
which is mode-dependent.
It also may need to know the version of the hardware and firmware, as
the behavior of application firmware 2.0 is significantly better than
version 1.1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This mode is documented as producing a raw result every 250 ms that the
application must convert to eCO2 and eTVOC readings. In practice
application firmware 2.0 appears to convert the readings as with all
other rates.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Expose the entire content of the ALG_RESULT_DATA block to the
application, primarily so the status and error flags can be seen. With
those available the application has the ability to detect that a stale
result has been provided so sensor_fetch_sample() can return -EAGAIN in
this case instead of -EIO, and it doesn't need to block which is
annoying.
This should also make the sensor usable on older Nordic Thingy:52
devices with outdated CCS811 application firmware that doesn't properly
implement the DATA_READY bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Accurate estimate of gas presence requires temperature and humidity
data. Add API to update these values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use CMSIS-standard bit mask and offset macros. Rename the field to more
closely match the data sheet. Use slightly less magic numbers for the
scale multipliers.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Proper use of the CCS811 requires maintenance of the BASELINE
register value measured in clean air at various points in the sensor
life cycle. The sensor driver abstraction has no facility to support
this, so add an application header with functions to fetch and update
the register value.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add the standard suite of trigger configuration options. Add driver
support for the DATA_READY and THRESHOLD triggers. Note cross-module
dependency as configuring the trigger requires a controlled modification
of the sensor registers and the sensor driver API doesn't support this.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The original implementation relied on the DATA_READY bit of the STATUS
register to indicate when a reading was available. This bit remains
clear for the first several readings produced by the CCS811.
When INT_DATARDY is set in MEAS_MODE the nINT signal will remain
asserted until ALG_RESULT_DATA is read. If this is treated as a LEVEL
signal, which is the common case in Zephyr, gating the read of
ALG_RESULT_DATA on DATA_READY means the signal will never be cleared,
and the interrupt callback will be repeated immediately.
Since the STATUS register value is part of the ALG_RESULT_DATA block
just read the whole thing, and provide its content to the user only if
the DATA_READY bit is set.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 has a measurement lifecycle that includes certain timing
constraints, including that calibration constants should not be applied
until the conditioning period has completed. If a device resets but the
CCS811 remains the process of inspecting current state and initializing
the device properly can be complicated.
Simplify this by forcing a reset of the device when the driver is
initialized. Should this cause hardship the necessary logic and
infrastructure to record time-of-last-reset across reboots and verify
measurement mode/baseline consistency can be added at that point.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Read the status and error in one function that provides its own
diagnostics.
Also change name of register to match datasheet.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 can be in either boot mode (after powerup) or application
mode, and these modes have distinct register maps that share only some
content. The register written to switch from boot mode to application
mode is not available in application mode, so don't write to it in that
case.
Also respect the required timeout between APP_START and next I2C
operation.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Allow application to choose the measurement rate.
Measurement mode 4 (250 ms rate) is not supported because it we have no
support for processing the raw data it produces.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Asserting the WAKEn increases current draw. Turn it off when I2C is
not being used.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the flash peripheral found in the SAME5x/SAMD5x
line of MCUs.
The peripheral is very simmilar to the one found on SAMD2x with only
a few register names changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Refactors the mcux gpt driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux igpio driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds BME280 SPI chip select pin control if chip select is
configured for the device in the device tree.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Need to set device busy when enter into transceive function
in SPI DW driver.
In current SPI DW driver the transceive function don't set busy state,
but that is important for PM busy state.
This will lead to unexpected behaviors when system calls this
function and enter into idle state.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Prior to this you would get compilation error when building
samples for the nrf5340_dk_nrf5340_cpuappns board.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
calling UARTE power management with DEVICE_PM_SUSPEND_STATE
then DEVICE_PM_OFF_STATE causes a deadlock in while loop.
It waits for an event witch never comes
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
EEPROM simulator and native_posix have been unified to one solution,
the old eeprom,native_posix is removed.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a eeprom simulator. The PR limits the addition to
qemu_x86 but it can easily be added to other devices by defining the
eeprom simulator in the dts and setting 'CONFIG_EEPROM_SIMULATOR=y'
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In STM32 flash driver, don't use semaphore if multithreading
isn't defined.
If multithreading isn't defined, a call to sem_give function
generates a hardware fault exception.
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Before establishing the ppp connection, windows sends the string CLIENT
and expects the reply CLIENTSERVER from the modem.
This functionality is implemented in the new function
ppp_handle_client().
This feature must be enabled via Kconfig.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Correct handling of device encoded temperature values, which combine a
12-bit 2s complement signed value with a separate sign bit. Rework
conversion between device and sensor temperature representations to
support negative temperatures in both domains.
Use a much simpler trigger configuration where the alert is driven by
comparator output, rather than as an interrupt that requires a pair of
I2C transactions to read and clear the flag.
Refactor the trigger infrastructure to use the setup/handle/process
idiom, which reduces duplicated code and to correctly detect alerts
present when the triggers are set.
Completely replace the sample with something that demonstrates
updating upper and lower threshold values to track moving
temperatures.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Added autocompletion to 'sensor get' command. After this change
device and channels are autocompleted. It is possible to provide
multiple channels for reading.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When asserts were disabled then sensor accepted any channel in
hts221_channel_get(). Changed to return -ENOTSUP when invalid
channel is provided.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
MPU6050 no longer using Kconfig to specify I2C addresses. Reference
to the removed symbol causes QA diagnostics. Remove the reference;
when AK8975 is converted to devicetree it may be possible to restore
the link between the sensors.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
