Some external audio devices require a master clock to be provided by
the I2S peripheral to work correctly. To allow for the operation of
these devices the master clock output should always be enabled when in
master mode.
Specific applications requiring this signal to be output can configure
the desitnation pin via the pinmux driver.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
Like other STM32 series the STM32L4x SoCs have an internal voltage
reference source that need to be enabled.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
CONFIG_GPIO_MCUX_LPC_PORT0_NAME and CONFIG_GPIO_MCUX_LPC_PORT1_NAME
aren't used anywhere so we can just remove them.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The UART driver for samd0 was is missing the .configure and
.config_get functionality expected from api for serial driver.
This commit fixes this by providing basic configuration
Signed-off-by: Kuba Sanak <contact@kuba.fyi>
This commit adds a reference to the SAM E54 maximum queue count value
in the device tree for specifying the range of `ETH_SAM_GMAC_QUEUES`
configuration.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
This commit adds the GMAC driver support for the Ethernet-capable SAM0
family devices (SAM E53 and E54 at this time).
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Some sensor drivers modify there struct's based on DT defines. In those
cases we need to make sure that DT_DRV_COMPAT is set on all the source
files associated with that driver. This updates any such files.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
define the irq handler in case of DMA V1 or V2,
for the stm32x soc series
with DMA V1 raise Fifo Error if enabled
with V2, handle the Global Interrupt
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Return an error if the direction of the channel is wrong
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move tables declaration as they are only used locally for now
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Control values when configuring the dma channel
According to the soc specification,
the dma V2 channel counts from 1.
the dma V1 stream counts from 0.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This is needed if muxing is enabled in which case we must
change the UART to muxing UART after the AT+CMUX command
has succeed.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of global workqueue, use own one so that the users of this
driver can more conveniently use global one. This means GSM modem
can work better with the UART muxing driver.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of using physical UART to connection to the modem, use
the GSM 07.10 muxing protocol and UART mux driver to create
virtual channels to the modem. This will allow simultaneous
PPP, AT and other type connections to the modem.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
By default PPP interface is not taken up automatically but only
after the PPP connection to modem is ready.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Create support for muxed UARTs which are attached to a real
UART and which use GSM 07.10 muxing protocol to create virtual
channels that can be run on top of the real UART.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add support to GSM 07.10 muxing protocol which is used to
share the same UART for PPP and AT commands among other things.
This allows e.g., the modem to send SMS and have PPP connection
active at the same time.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Fixed the ETH_SAM_GMAC_QUEUES config by adding if-statements per SoC
series.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This commit updates the Atmel SAM GMAC driver to select max frame size
value from the device tree. Now GMAC driver can operate with the three
different frame size options available.
The current supported values are: 1518, 1536 and 10240.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current setup of physical layer forces RMII interface. The code was
refactored to have only one point to select proper phy interface. Now,
GMAC driver works with both RMII or MII interface. The phy connection
type is now selected by device tree. The default phy connection is RMII.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The NOCACHE_MEMORY can be enabled only for those MCU that support data
cache. The currently SoC that doesn't have data cache is SAM4E.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Improve data cache conditional build. Now data cache code is build
only if device have support to it. This enables GMAC driver for use
with devices that don't have data cache instructions.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
This cleans up DMA flags by separating the necessary flags for devices
with one or multiple RX/TX queues.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The radio driver will now notify the upper layer about Frame Pending Bit
value in the ACK response it sent.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
clock-generator is a normal property. To access it we should use
DT_INST_PROP(0, clock_generator) and not DT_INST_CLOCKS_CELL().
Fixes: #24399
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Sets the "dummy data" value to send when the transmit buffer is null.
Fixes the spi_null_tx_buf test in tests/drivers/spi/spi_loopback on the
lpcxpresso54114 board.
Tested on frdm_k64f, mimxrt1050_evk, and lpcxpresso54114_m4 boards.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
DIO handlers defined in loramac-node are quite complex. Additionally
they call read/write operations over SPI with the sx1276 chip. This
cannot work properly in interrupt context, so call DIO handlers in
system workqueue instead.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far only GPIO pin number of registered DIO line was compared with
arguments passed to GPIO callback. This is not enough when multiple gpio
controllers are used for DIO lines. As an example when DIO0 is on PA1
and DIO1 is on PB1, then DIO0 handler is called all the time.
Compare GPIO controller (in addition to pin number) of DIO lines with
the argument passed to gpio callback, so proper DIO handler is used.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This information is filled during build time from device-tree. This is
not supposed to change in runtime, so make it const.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Part of sx1276 driver which is in loramac-node module passes to Zephyr
irqHandlers with callbacks. Some of those callbacks can be NULL and this
is true now (with the current version of loramac-node) for DIO5. If we
define all 0-5 DIOs in dts, then this results in interrupts which are
unwanted. As we do not check that loramac-node callback is NULL, then we
crash trying to call it.
Check every handler during initialization and just skip initialization
of GPIO if it is NULL. This also prevents crashes, because there is no
way GPIO interrupt to be triggered in runtime for this DIO.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
The PORCTRL setting command is in 'bank2' and so might not be changed on
the controller unless bank2 is enabled first.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
Make use of DT_NODELABEL macros to get device instances
information to configure drivers I2C instances.
This allows to remove I2C related lines in fixup.h files
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Use compatible information to configure i2c stm32.
With this, driver version selection is done thanks to compatible
and it is not needed anymore to do this via Kconfig symbol
selection under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert the LMP90xxx ADC driver from using k_sleep() to using
k_msleep() in order to resolve a compilation error caused by passing
an int to k_sleep().
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Convert driver from DT_FLASH_BASE_ADDRESS and DT_FLASH_DEV_NAME to use
DT_REG_ADDR and DT_INST_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
The soc_flash_mcux supports several possible compatible so handle that
as part of how we set DT_DRV_COMPAT.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
For a flash driver DT_DRV_COMPAT should be the compatible for the flash
controller and not the soc-nv-flash. Change to driver to use the flash
controllers compatible and get the soc-nv-flash properties as a child of
that controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use new DT_INST macros throughout. Removed per
instance Kconfig symbols and replaced with DT_NODELABEL references where
needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The 32 KiBy bulk erase command was being invoked without respecting
the flag that indicates it's supported. Make the invocation
conditional.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use the new devicetree API. Remove per-board enabling of ADC_0 by
setting ADC_0 to default y when the 'adc' node label points at an
enabled node of the expected compatible (depending on SoC).
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Now that all entropy drivers use DTS we can remove HAS_DTS_ENTROPY being
set everywhere as well as Kconfig ENTROPY_NAME since that is now coming
from DT_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use the UNALIGNED_GET() macro instead of the
flash_sam0_read_unaigned_u32() function to ensure
word alignment of the source address.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
drivers: flash: sam0: fix whitespace
Fix checkpass whitespace error.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_I2C_._NAME macro with DT_LABEL(DT_NODELABEL()) instead. This
will allow us to remove all references to DT_I2C_._NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Updated the openisa,rv32m1_vega-pinmux binding to require the label
property and updated the rv32m1.dtsi to add label properties for the
pinmux nodes.
Also update gpio_basic_api test to use DT_NODELABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When configuring the I2S peripheral as a master, the DMA channel
direction must be configured to transfer data from memory to the
peripheral.
Currently the configuration of channel direction is always set for
peripheral to memory regardless of whether it is the TX or the RX
channel.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
HWINFO drivers should be responsible for ensuring that
the data structure is a sequence of bytes. That is not
what the current sam0 and nordic drivers do. The drivers
read the data as u32_t and then memcpy the data to a
buffer. This ensures the data has the endianness of the
underlying MCU, which in this case is Cortex M0 which
is little endian.
This commit fixes the endianness so the data can be
interpreted as a "left to right sequence of bytes".
This commit updates the API doc to provide clarification
of the data structure.
Add to 2.3 release notes.
Fixes#23444, #24103
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Obtain RX time from the radio driver. Fill the `net_pkt` with
a timestamp if `NET_PKT_TIMESTAMP` is enabled.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
nRF radio driver will call `nrf_802154_transmit_failed` callback in case
no ACK is received, so we do not need to set timeout at the shim layer
anymore.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Update `flash` shell commands to take an optional device argument,
instead of using the chosen flash device.
Signed-off-by: Ivo Clarysse <ivo@bcdevices.com>
Adds a shim layer around the mcux lpc flexcomm driver to adapt it to the
zephyr i2c interface. It leverages heavily from the existing mcux lpi2c
shim driver.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Replace DT_FLASH_DEV_BASE_ADDRESS with new DT_REG_ADDR/DT_INST macro as
we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_WRITE_BLOCK_SIZE with new DT_INST_NODE_HAS_PROP and
DT_INST_PROP macro as we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace DT_FLASH_DEV_BASE_ADDRESS with new DT_REG_ADDR/DT_INST macro as
we phase out DT_FLASH define usage.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Replace use of DT_FLASH_DEV_NAME with DT_INST_LABEL in drivers as we
want to phase out DT_FLASH_DEV_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When a DMA stream is successfully disabled, the function should
immediately return with a success status.
Signed-off-by: Abe Kohandel <abe@electronshepherds.com>
DT_CALL_WITH_ARG() is an internal implementation detail that should
not be used outside of devicetree.h.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The duration is used in math with the uptime clock, not as a timeout.
Correct value expression and rename to clarify units.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use valid stm32 flash driver compatibles instead of flash
area compatible.
For 'write_block_size' property, use reference to soc-nv-flash.
fixes#23997
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Create a dedicated config symbol for video device initialization.
Generally, video device init is low priority comparing to standard
devices. Moreover some video device can rely on other device init,
like the csi mcux driver which rely on sensor and i2c init.
This fixes a crash in video capture sample, when camera sensor
(mt9m114) is not connected.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Notify about actual data transmission start.
Needed when ACK timeout is disabled in the radio driver.
Signed-off-by: Marek Porwisz <marek.porwisz@nordicsemi.no>
When enabled, instead of erasing entire flash page at once, page will
be erased in defined time slices. Erasing single page stalls CPU
for significant time share (~80ms) and partial erase divides the
operation in to the shorter time periods, resuming CPU operation in
meantime and enabling better scheduling of time sensitive operations.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
The recent change in 2.2.0 that disables the watchdog
on boot introduced a hard fault when a log message
is generated too early before even the RTC is
initialized.
This commit removes the log message.
Signed-off-by: Steven Slupsky <sslupsky@gmail.com>
Add an optional weighted average filter to the ADC readings in the NXP
Kinetis temperature sensor driver as recommended in NXP AN3031.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Fix a potential 32 bit multiplication overflow (muliplying by 10000
instead of 1000000) and change the calculations and units accordingly.
Improve the code readability and traceability towards NXP AN3031 by
using the same variable name as in the application note.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
sys_clock_disable now is only called in sys_reboot.
This API is outdated, no need to implement it and
there is a weak version.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* add interrupt lock in low level API to gurantee the
correctness of operations.
* make some functions as in-line functions
* clean up and optimize the code comments
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
wifi-reset-gpios is currently ignored after conversion to DT_INST
macros. Use wifi_reset_gpios instead of reset_gpios to fix the problem.
Fixes: a464ae7163 ("drivers: wifi: esp: Convert to new DT_INST
macros")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
To ease driver configuration, enable ENTROPY_STM32_RNG
only if device node matching driver compatible is enabled.
No more need to enable config symbol under soc/
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Convert stm32 entropy driver to configuration based on device tree.
Select HAS_DTS_ENTROPY symbols and configure CONFIG_ENTROPY_NAME
in fixup files.
Since rng node is not enabled (or available) on all boards, it could
happen that symbol ENTROPY_STM32_RNG is not enabled and hence
ENTROPY_HAS_DRIVER not selected which ends up with a symbol
ENTROPY_NAME defined throufg Kconfig selection. Thus, in fixup file,
CONFIG_ENTROPY_NAME is defined only if not already defined.
Additionally, update boards that used to configure entropy by default.
On these boards, enable rng device in device tree and remove Kconfig
related configuration (which should not be part of default
configuration).
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Fixup cases of GPIO_PORT_PIN_MASK_FROM_NGPIOS(DT_INST_PROP(n, ngpios))
to use GPIO_PORT_PIN_MASK_FROM_DT_INST(n) instead.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
With the introduction of the new device-tree macros it is now possible
to use the settings for speed and flow-control from the bus node instead
of having the same properties on the esp node itself.
Signed-off-by: Tobias Svehagen <tobias.svehagen@gmail.com>
Instead of using Kconfig options for setting the device name and IRQ
priority for the entropy_nrf5 driver, get these settings from the rng
node defined in DTS for a given SoC.
Provide also fixups for CONFIG_ENTROPY_NAME, until applications using
entropy drivers are converted to use DTS as well.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
We rename the nRF53 Dev Kit board target (nrf5340_dk_nrf5340)
to nrf5340pdk_nrf5340. We update all associated references
in the supportive documentation and all nRF5340-related
cofigurations and overlay files in the samples and tests
in the tree.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Also update counter_basic_api test to use DT_INST and remove the
udoo_neo_full_m4.conf as its not longer needed since the per instance
Kconfig sybmols don't exist anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST macros and remove related board per
instance Kconfig symbol usage.
Additionally remove udoo_neo_full_m4.conf from gpio_basic_api test since
the Kconfig symbols don't need to be set anymore.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
All GPIO controller drivers support DTS so we can select HAS_DTS_GPIO
at the GPIO driver subsystem level rather than for each specific driver.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When disabling the interrupt current implementation of the
gpio_pin_interrupt_configure function will first reconfigure the
interrupt to be active on gpio low level.
Since the pin interrupt is enabled if the gpio pin level happens
to be low at the time the interrupt will trigger immediately.
Rewrite the function to disable the interrupt in a safe manner.
Signed-off-by: Frank Li <lgl88911@163.com>
The net_buf subsystem is now fully compatible with the new timeout
API, so move the selection of the legacy API to those specific
subsystems that use net_buf and still need converting.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Delay radio abort called in the flash driver to emulate the
behavior of pre-empt timeout in Bluetooth LL split
controller. Without this, the driver aborted radio events
in its reserved time space.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
At present wdt_gecko driver supports ULFRCO as its only clock source.
Select the clock explicitly, do not rely on the default configuration
provided by the SiLabs header files. The default configuration is
changing between different SiLabs HAL versions.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Enable the gpio_sx1509b driver by default when a "semtech,sx1509b"
compatible node is enabled in devicetree.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Make I2C and SPI drivers for nRF SoCs no longer dependent on Kconfig
options that enable instances (i.e. I2C_x and SPI_x). Now these drivers
enable hardware instances when corresponding nodes in devicetree are
enabled (have status "okay").
For I2C, SPI, and UART drivers, instead of using Kconfig dependencies
to prevent enabling of hardware instances that cannot be used together
(e.g. SPIM1 and TWIM1), a file that signals invalid configurations with
build assertions is added to compilation.
Also dependencies on HAS_HW_NRF_* options are removed from Kconfigs
of I2C, SPI, and UART drivers, as for hidden options that activate
proper type of driver such dependencies are not actually helpful.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `UART_x_NRF_UART*` that select
the type of nrfx driver (for UART or UARTE peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding UART node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between UART and UARTE for a given instance.
Since all `UART_x_NRF_UART*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `I2C_x_NRF_TWI*` that select
the type of nrfx driver (for TWI or TWIM peripheral) to be used
for a given instance. This prevents the options from being modified
from configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding I2C node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between TWI and TWIM for a given instance.
Since all `I2C_x_NRF_TWI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Remove prompts from Kconfig options `SPI_x_NRF_SPI*` that select the
type of nrfx driver (for SPI, SPIM, or SPIS peripheral) to be used
for a given instance. This prevents the options from being modified
in configuration files.
Instead, make one of these options selected by default according to the
"compatible" property set for the corresponding SPI node in devicetree.
This eliminates the need of changing both the "compatible" property in
devicetree and the Kconfig option selecting the driver type when a user
wants to switch between SPI, SPIM, and SPIS for a given instance.
Since all `SPI_x_NRF_SPI*` options are made "hidden" by this commit,
all their occurrences in configuration files are removed.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add CSMA CA capability for the `ieee802154_nrf5` radio driver along with
appropriate implementation in the `nrf5_tx` function.
Introduce 802.15.4 radio driver with CSMA/CA support enabled. Add help
text, mentioning a list of peripherals occupied by the radio driver.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Even though radio driver can report in its capabilities that it does
support CSMA CA, there's no way in the driver to select how the frame
should be transmitted (with CSMA or without). As layers above radio
driver (Thread, Zigbee) can expect that both TX modes are available, we
need to extend the API to allow either of these modes.
This commits extends the API `tx` function with an extra parameter,
`ieee802154_tx_mode`, which informs the driver how the packet should be
transmitted. Currently, the following modes are specified:
* direct (regular tx, no cca, just how it worked so far),
* CCA before transmission,
* CSMA CA before transmission,
* delayed TX,
* delayed TX with CCA
Assume that radios that reported CSMA CA capability transmit in CSMA CA
mode by default, all others will support direct mode.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Convert driver to utilize the new DT_INST macros completely and remove
associated Kconfig symbols that now come from devicetree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The ft5336 has an interrupt that can be used instead of polling
this commit adds support for using it but as an option to maintain
compatibility. Tested on the stm32f746g_disco board.
Signed-off-by: Mark Olsson <mark@markolsson.se>
Run the int_literal_to_timeout Coccinelle script to fix places where
it is clear that an integer duration is being passed where a timeout
value is required.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Use device node declaration instead.
Clean up GPIO_STM32_PORT* Kconfig symbols.
On some boards some gpio ports where disabled using Kconfig symbols.
Disable them now via device tree nodes in boards dts files.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Move towards use DTS for driver instance name instead of Kconfig sybmol.
This is towards phasing out CONFIG_ENTROPY_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Commit 7832738ae9 ("kernel/timeout: Make timeout arguments an opaque
type") changed the forever value for timer drivers to K_TICKS_FOREVER
from K_FOREVER.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
