Commit 5a9a33b0cf changes interrupt
destination in an attempt to broadcast interrupts. However, this
change causes interrupts to stop working on the UP Squared board
in non-SMP configuration. According to QEMU source code,
physical destination address 0xFF000000 is a special case where
it broadcasts the interrupts. However, none of the IOAPIC
documentation (that I can find) describes this behavior. So,
revert that commit.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
When SMP is enabled, the kernel expects that interrupts be delivered
to all CPUs in the system. Change the I/O APIC RTEs accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
The existing device_set_power_state() API works only in synchronous
mode and this is not desirable for devices(ex: Gyro) which take
longer time (few 100 mSec) to suspend/resume.
To support async mode, a new callback argument is added to the API.
The device drivers can asynchronously suspend/resume and call the
callback function upon completion of the async request.
This commit adds the missing callback parameter to all the drivers
to make it compliant with the new API.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
Update reserved function names starting with one underscore, replacing
them as follows:
'_k_' with 'z_'
'_K_' with 'Z_'
'_handler_' with 'z_handl_'
'_Cstart' with 'z_cstart'
'_Swap' with 'z_swap'
This renaming is done on both global and those static function names
in kernel/include and include/. Other static function names in kernel/
are renamed by removing the leading underscore. Other function names
not starting with any prefix listed above are renamed starting with
a 'z_' or 'Z_' prefix.
Function names starting with two or three leading underscores are not
automatcally renamed since these names will collide with the variants
with two or three leading underscores.
Various generator scripts have also been updated as well as perf,
linker and usb files. These are
drivers/serial/uart_handlers.c
include/linker/kobject-text.ld
kernel/include/syscall_handler.h
scripts/gen_kobject_list.py
scripts/gen_syscall_header.py
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
irq_lock returns an unsigned int, though, several places was using
signed int. This commit fix this behaviour.
In order to avoid this error happens again, a coccinelle script was
added and can be used to check violations.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
If IOREGSEL register is not accessed with 32 bits, it may not be
intercepted by type 1 hypervisor correctly.
Signed-off-by: Zide Chen <zide.chen@intel.com>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I08f51e2bfd475f6245771c1bd2df7ffc744c48c4
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Current users of sys_bitfield*() are bending over backwards to cast
what is most of the times a pointer into an integer.
Bitfields can be better described with an void *, so
uint{8,16,32,64}_t or any other container can be used. Most
sys_bitfield*() operations, by extension, can do the same. Note void *
has byte arithmetic, like char *.
This change will also make it implicit, for any future split of the
address space between virtual (what the SW is seeing) and physical
(what the HW is seeing) way clearer, as the functions dealing with
physical, non directly referentiable/mappeable addreses to use an
integer type, like mem_addr_t.
- include/arch/ARCH/*asm_inline*:
- sys_bitfield*() all modified to take 'void *'
Note 'void *' arihtmethic is byte based, which makes some things
easier.
- include/sys_io.h:
- introduces DEFINE_BITFIELD
- update docs
- tests/kernel/bitfield: remove all the cast contortions, use DEFINE_BITFIELD
PENDING: update other TCs
- include/arch/nios/nios2.h, drivers/interrupt_controller/ioapic_intr.c:
remove cast contortions
Change-Id: I901e62c76af46f26ff0d29cdc37099597f884511
Jira: ZEP-1347
Signed-off-by: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com>
Replace the existing Apache 2.0 boilerplate header with an SPDX tag
throughout the zephyr code tree. This patch was generated via a
script run over the master branch.
Also updated doc/porting/application.rst that had a dependency on
line numbers in a literal include.
Manually updated subsys/logging/sys_log.c that had a malformed
header in the original file. Also cleanup several cases that already
had a SPDX tag and we either got a duplicate or missed updating.
Jira: ZEP-1457
Change-Id: I6131a1d4ee0e58f5b938300c2d2fc77d2e69572c
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit replaces the nanokernel.h include by kernel.h.
Change-Id: Ib42fbf2d9f77a73c0831f569b3dbbfb342ea2e1d
Signed-off-by: Flavio Santes <flavio.santes@intel.com>
PRIMARY, SECONDARY, NANOKERNEL, MICROKERNEL init levels are now
deprecated.
New init levels introduced: PRE_KERNEL_1, PRE_KERNEL_2, POST_KERNEL
to replace them.
Most existing code has instances of PRIMARY replaced with PRE_KERNEL_1,
SECONDARY with POST_KERNEL as SECONDARY has had a longstanding bug
where the documentation specified SECONDARY ran before the kernel started
up, but actually ran afterwards.
Change-Id: I771bc634e9caf7f17dbf214a270bc9967eed7d32
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
In some cases we can either assume they are already masked
at boot and save some cycles, or the IOAPIC has configuration
from a prior boot stage that needs to be preserved.
Change-Id: I0c71ff0f01a6ee13a3b9c9e239d5a933d6cb6542
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Update the power sample and drivers with the new device driver power
management API using the existing logic
Jira: ZEP-954
Change-Id: Idd94232e458767635973e94e9fc673c01612c1e2
Signed-off-by: Amir Kaplan <amir.kaplan@intel.com>
Save and restore IOAPIC flags and irq to vector translation
info for supporting deep sleep.
Jira: ZEP-223
Change-Id: Ifc50a5a72699ff6782ad194d8e96b18fac34da18
Signed-off-by: Jithu Joseph <jithu.joseph@intel.com>
Mostly SoC initialization and some kernel subsystems, but also some
device drivers like the interrupt controllers.
Change-Id: I8dc1844c33acd877c075b6b03558fdca6f87500b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
This is the last step before obsoleting DEVICE_DEFINE() and
DEVICE_INIT_CONFIG_DEFINE().
Change-Id: Ica4257662969048083ab9839872b4b437b8b351b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_DEFINE() so that it fits in the 'device' namespace.
Change-Id: I3af3a39cf9154359b31d22729d0db9f710cd202b
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Rename it to DEVICE_INIT_CONFIG_DEFINE(), because (a) it was not fitting
in any namespace and (b) it is not used to declare, but rather define a
object.
Change-Id: I1da5822f06b85a9fb024b5b184afd0ccc01012ec
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
The interrupt API has been redesigned:
- irq_connect() for dynamic interrupts renamed to irq_connect_dynamic().
It will be used in situations where the new static irq_connect()
won't work, i.e. the value of arguments can't be computed at build time
- a new API for static interrupts replaces irq_connect(). it is used
exactly the same way as its dynamic counterpart. The old static irq
macros will be removed
- Separate stub assembly files are no longer needed as the stubs are now
generated inline with irq_connect()
ReST documentation updated for the changed API. Some detail about the
IDT in ROM added, and an oblique reference to the internal-only
_irq_handler_set() API removed; we don't talk about internal APIs in
the official documentation.
Change-Id: I280519993da0e0fe671eb537a876f67de33d3cd4
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Quark SE Lakemont core has a hardware bug where the LOAPIC does
not properly notify the IOAPIC to clear the IRR bit for level-
triggered interrupts.
This patch introduces a workaround where the vector ID of the
in-service interrupt is manually written to the IOAPIC_EOI
register, resulting in the bit being cleared.
Unfortunately, in the context where EOI happens it's very difficult
to identify which IRQ line is being serviced, so this is done
unconditionally for all interrupts vectors whether they are registered
in the IOAPIC RTE table or not.
Change-Id: I639cd258dec4f50934e17eadbb821e6a7112e636
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The initialization code and macros are the same. So extracts it
and puts it into the driver. This is another step to follow
the driver model.
Those empty C files are there because the current Kbuild
requires Makefile to be present at those directories,
(due to arch/x86/Kbuild), which requires building some object
files. So the empty source files are there to produce empty
object files to satisfy this.
Change-Id: I14056347ea14cff227d9e8960192e8673c0019b8
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
XIOAPIC_DIRECT_ADDRESSING and IOAPIC_MSI_REDIRECT are never
set and not tied to any config options.
Change-Id: Ib64cd198c99fe670eb5bcd946ce93f616c03d12a
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This was only needed for the older 8259A style PICs which are no
longer supported.
Since we now just support APIC, we always just call loapic_eoi which
no longer requires an argument and informs the IOAPIC that the interrupt
is complete if necessary.
Change-Id: I15c9b7b4f03b872656220af32220b62e043bfa6b
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Change all the Intel and Wind River code license from BSD-3 to Apache 2.
Change-Id: Id8be2c1c161a06ea8a0b9f38e17660e11dbb384b
Signed-off-by: Javier B Perez Hernandez <javier.b.perez.hernandez@linux.intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Allan Stephens <allan.stephens@windriver.com>
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Change the IOAPIC driver to be initialized directly from the init
system. The function signature of _ioapic_init() function is updated
accordingly.
Change-Id: I2f824ac745926966eebb23f60445a41e1df9eb8f
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Use doxygen format for file documentation and move
parameters to be part of the function comments.
Change-Id: I01c0614e7cd3ef4c689d2aec3aa3e52e0d21ffcd
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removes the LOAPIC and IOAPIC macros from board.h as they are no longer
appropriate since Kconfig options exist to use in their stead.
Change-Id: I2ce41a7a08d1859682389f35cd5a97c0e2cd5bf7
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
The Zephyr kernel must always be built as a monolithic image, not as
separate nanokernel and microkernel images.
Change-Id: I44fdd2349b32f409c84710f58bc4b3fe96fd79b7
Signed-off-by: Benjamin Walsh <benjamin.walsh@windriver.com>
Removes references to obsolete BSP terminology. Where appropriate, replaces it
with platform terminology.
Change-Id: Ifb17f98bc12d3a28198810351629a109abdc18a5
Signed-off-by: Peter Mitsis <peter.mitsis@windriver.com>
Remove function name from comment and add @brief instead.
Also capitilize first letter.
Change-Id: Ib708b49bf02e5bc89b0066637a55874e659637e0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Previous comment style used RETRURNS:, use @return to comply
with javadoc style.
Change-Id: Ib1dffd92da1d97d60063ec5309b08049828f6661
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The change replaces multiple asterisks to ** at
the beginning of comments and adds a space before
the asterisks at the beginning of lines.
Change-Id: I7656bde3bf4d9a31e38941e43b580520432dabc1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
