CONFIG_I2C_NRF5_GPIO_SDA_PIN and CONFIG_I2C_NRF5_GPIO_SCL_PIN are
replaced with port specific versions. Board defconfigs relying on the
original names are updated. The driver is also modified to pass the
configure values to registers.
Signed-off-by: Aapo Vienamo <aapo.vienamo@iki.fi>
Use "select USE_STM32_LL_I2C" to select the needed STM32 LL files,
instead of editing ext/hal/st/stm32cube/CMakeLists.txt
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
Wrong buffer assigned for receiving the last 2 bytes in multi
byte reception of STM32F4 i2c driver. Change the buffer to
correct one.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
According to STM32F4 reference manual, software should wait for BTF=1
before reading N-2 data byte.
Reference:
"For N >2 -byte reception, from N-2 data reception" section, page
853 of STM32F4 Reference manual.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
We can have a spurious error while performing a transfer using IRQ. This
happens when the last message of the transfer is a read with a STOP
condition. We must disable the RX interrupt while waiting for the STOP
interrupt, otherwise we will get a spurious RX interrupt which will lead
to an error.
Signed-off-by: Florian Vaussard <florian.vaussard@gmail.com>
This was validated on the cc3220sf_launchxl board
using the Zephyr thermometer sample program
adapted to call the i2c driver directly, and fetching
samples from the on-board TMP006 temperature sensor.
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Waiting for transfer complete and stop condition uses while loops
even when interrupt mode is enabled.
Implement use of TC, TCR and STOP interrupt for interrupt mode.
msg_done is not needed in interrupt mode anymore, so move it
to non-interrupt section
Tested with stm32f3_disco board.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Disabling of Interrupts is duplicated. Move it to a position
that is common to messages that end with and without errors.
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Rename the Atmel SAM I2C driver based on TWIHS module to match the
convention:
<driver class>_<SoC family>_<hardware module used by the driver>
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Various minor changes to the Atmel SAM (TWIHS) driver
- clean up variable names, comments
- refactor i2c_clk_set function
- do not save configuration in dev_data
- improve ISR NACK handling
- print "Device initialized" string
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Event ISR checks if the TX/RX interrupts is enabled instead
of the TXIS/RXNE interrupt status flags. Use the TXIS/RXNE
interrupt status flags to check which interrupt event
happened.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
STM32 I2C driver doesn't use the I2C API flags STOP/RESTART,
instead it uses its own RESTART flag. As a result, I2C API's
i2c_burst_write* funtions doesn't work. This patch makes
STM32 I2C driver to use I2C API flags.
Tested on: 96b_carbon, olimexino_stm32 (i2c_ll_stm32_v1)
Tested on: stm32f3_disco, disco_l475_iot1 (i2c_ll_stm32_v2)
Fixes: #4459
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
Introducing CMake is an important step in a larger effort to make
Zephyr easy to use for application developers working on different
platforms with different development environment needs.
Simplified, this change retains Kconfig as-is, and replaces all
Makefiles with CMakeLists.txt. The DSL-like Make language that KBuild
offers is replaced by a set of CMake extentions. These extentions have
either provided simple one-to-one translations of KBuild features or
introduced new concepts that replace KBuild concepts.
This is a breaking change for existing test infrastructure and build
scripts that are maintained out-of-tree. But for FW itself, no porting
should be necessary.
For users that just want to continue their work with minimal
disruption the following should suffice:
Install CMake 3.8.2+
Port any out-of-tree Makefiles to CMake.
Learn the absolute minimum about the new command line interface:
$ cd samples/hello_world
$ mkdir build && cd build
$ cmake -DBOARD=nrf52_pca10040 ..
$ cd build
$ make
PR: zephyrproject-rtos#4692
docs: http://docs.zephyrproject.org/getting_started/getting_started.html
Signed-off-by: Sebastian Boe <sebastian.boe@nordicsemi.no>
Fixes#4429
Driver didn't work properly when a transfer consisted of multiple
messages.
Fix doesn't use auto end mode anymore. msg_done function waits for
transfer to complete and issues stop condition if necessary.
Tested with stm32f3_disco board and samples/drivers/i2c_fujitsu_fram
example adapted to use I2C_1 as I2C_DEV
Signed-off-by: Daniel Wagenknecht <wagenknecht@clage.de>
i2c actually only has two entry points into the driver,
i2c_configure and i2c_transfer. All the other APIs are derived
from these.
All derived APIs now just call i2c_transfer() with appropriate args.
The handler for i2c_transfer() needs to examine the message array
and validate all the buffers involved depending on whether we are
reading or writing to them.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This ensures DW_apb_i2c correctly transmits the slave address (7 or
10 bit) based on ic_10bitaddr_master when configured in master mode.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
The ic_tar and ic_sar were earlier set to 9 bits but now its
corrected to consider 10 bits.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Atmel SAM3X series has been recently converted to use ASF and
should now use common SAM family drivers. The i2c_atmel_sam3
I2C driver will be removed in the future.
This commit also changes the default I2C driver for Arduino Due
board from i2c_atmel_sam3 to i2c_sam_twi.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Added I2C bus (TWI) driver for Atmel SAM MCU family. Only
I2C Master Mode with 7 bit addressing is currently supported.
Tested on Arduino Due board.
Origin: Original
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
STM32F0/3 I2C's independent clock source supports only
HSI and SYSCLK, not APB1. We force I2C clock source to SYSCLK.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
IRQ_CONNECT() was being expanded with the IRQ line for the first device
twice, causing spurious IRQs.
Should fix#4398.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Supports both master and slave mode, standard and fast modes,
configurable timeouts, and a few other tunable settings.
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Cleanup I2C drivers to not use bitfield access for config information
and instead use accessor macros that use shifts & masks. This is
cleanup towards removing the bitfield access in the future.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
I2C device drivers which support DTS have their default boot
configuration provided by DTS. The legacy I2C_x_DEFAULT_CFG
option in Kconfig is no longer required. This patch hides
this option from the Kconfig menu for I2C device drivers which
support DTS.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
The compilation of the i2c_ll_stm32 fails when we
enable the interrupt mode. The struct i2c_stm32_data
is needed to initialize the semaphore. This patch adds
the missing struct for interrupt mode.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Stop using CONFIG_I2C_x_DEFAULT_CFG to get the initial value. Since we
only support master mode we always default to it for initial config and
we get the bitrate from the device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add _i2c_map_dt_bitrate() that maps from a bitrate to the I2C zephyr
cfg bit fields used in i2c_configure().
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch fixes the read operation of the I2C driver
for all the receptions (1-byte, 2-bytes, N-bytes when
N > 2)
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Tested-by: Yannis Damigos <giannis.damigos@gmail.com>
Tested-by: Martin Iñaki Malerba <inakimmalerba@gmail.com>
In interrupt mode, the drivers entered a forever loop if the
I2C_MSG_RESTART flag was set. This patch fix this issue.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
The EVENT interrupt is generated when:
– SB = 1
– ADDR = 1
– ADD10= 1
– BTF = 1 with no TxE or RxNE event
– TxE event to 1 if Buffer interrupt enabled
– RxNE event to 1 if Buffer interrupt enabled
We need to disable and enable the Buffer TxE and RxNE interrupt
inside the EVENT ISR. The LL_I2C_{Enable,Disable}IT_TX and
LL_I2C_{Enable,Disable}IT_RX functions, used now, enable and
disable both Buffer and Event interrupt. This patch uses the
LL_I2C_EnableIT_BUF and LL_I2C_DisableIT_BUF functions to
enable and disable the Buffer interrupt (TxE, RxNE).
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Change the common "init with 0" + "give" idiom to "init with 1". This
won't change the behavior or performance, but should decrease the size
ever so slightly.
This change has been performed mechanically with the following
Coccinelle script:
@@
expression SEM;
expression LIMIT;
expression TIMEOUT;
@@
- k_sem_init(SEM, 0, LIMIT);
- k_sem_give(SEM);
+ k_sem_init(SEM, 1, LIMIT);
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Update the MCUX I2C driver and related platforms to get their I2C
information from the device tree. We also updated a few of the sensor
drivers found on the FRDM & Hexiwear boards to get their I2C bus name
from the device tree instead of directly from Kconfig.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As I2C_0 (port 0) isn't used on the STM32 platforms we didn't exclude
the related Kconfig options if DTS was enabled. However other SoCs
(like NXP) do use I2C_0 so we need to fixup the Kconfig dependencies
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Configure I2C using DT for the following STM32 boards:
disco_l475_iot1
nucleo_f401re
96b_carbon
olimexino_stm32
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
