Remove hardcoding and make the values configurable. Also make the
Kconfig variables consistent with other architectures.
Change-Id: I69334002303d4d8abaf7363d9134fd5f46ce4eeb
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Set the target to ARC to speed up flashing. the difference:
before
downloaded 27320 bytes in 50.685825s (0.526 KiB/s)
after
downloaded 27320 bytes in 3.396626s (7.855 KiB/s)
Change-Id: I53ca26f97eefd40e869662b137f5a659082aa478
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
There are two major issues with the kconfig:
() Some of the config options have incorrect dependencies inside help
under menuconfig. For example, CONFIG_GPIO depends on BOARD_GALILEO.
() Since the SoC and board specific kconfig files are parsed first,
the help screen would say, for example, CONFIG_SPI is defined at
arch/arm/soc/fsl_frdm_k64f/Kconfig. This is incorrect because
the actual config is defined in drivers/spi/Kconfig.
These cause great confusion to users of menuconfig/xconfig.
To fix these, the SoC and board defaults are now to be parsed last.
Note that the position swapping of defaults in this patch is due to
the fact the the default parsed last will be used.
And, spi_test is broken due to the fact that it requires
CONFIG_SPI_INTEL_PORT_1, but never enables it anywhere. This is
bypassed for now.
Origin: refactored and edited from existing files
Change-Id: I2a4b1ae5be4d27e68c960aa47d91ef350f2d500f
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This makes the board selection dependent on SoC selection. For example,
select Atmel SAM3 will only allow "Arduino Due" as board selection.
This disallows incompatible SoC/board combination, like K64F with
Arduino Due.
JIRA: ZEP-106
Change-Id: I675961cf33db5a0058fc68f14c8f16978f9c6b95
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Base address registers and IRQs are set in Kconfig.
Set proper SPI default to various quark_se_ss based boards.
Change-Id: Iadaae551f441457bef334f94f68cafa7c3e499d0
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- Use interface script from openocd distribution
- add debug support
Change-Id: If7e0ab0ad1fc6e67ca648a0a7c32356b3db90cf0
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Using the latest SDK (0.7.2) you can flash directly using make
by specifying the board, for example
make BOARD=arduino_101 flash
This will build and flash the generated binary to the board.
Change-Id: I90254abd69874efbb449ef318079958980c23074
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change terminology and use SoC instead of platform. An SoC provides
features and default configurations available with an SoC. A board
implements the SoC and adds more features and IP block specific to the
board to extend the SoC functionality such as sensors and debugging
features.
Change-Id: I15e8d78a6d4ecd5cfb3bc25ced9ba77e5ea1122f
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Define boards based on platforms/SoCs and define them under boards/.
Also unify the naming of all platform, SoC and board files and use
platform.h for platforms and board.h for boards.
Change-Id: Icfeb96479ab5800aca98c80a79bdc3cecd645314
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
