The channels assigned to the controller are reordered so that the ones
previously used and now available for other purposes have continuous
numbers. When the controller can take advantage of the pre-programmed
PPI channels (when TIMER0 is used as the event timer), the now free
channels are 0-4, when it cannot, it is the channel 0.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Couple of findings which were revealed after changing
LOG_MODULE_REGISTER macro:
- missing semicolons after LOG_MODULE_REGISTER()
- missing LOG_LEVEL defines
- other
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Log configuration was included only in case NET_L2_IEEE802154 was
enabled. In case of open thread this is not the case.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Introduce new Kconfig option for selecting either slip or ethernet
connectivity to host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Provide necessary error handling for `lis2dh_reg_read_byte` function
which might fail.
Also, use a common `status` variable to be used for storing the
error code.
Fixes#10590
Coverity-CID: 188733
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
The Kconfig variable for selecting neural network accelerator driver(s)
was changed from NEURAL_NET to NEURAL_NET_ACCEL
The CMakeLists.txt however, was not updated to use the updated variable
This commit updates CMakeLists.txt to include neural_net if
CONFIG_NEURAL_NET_ACCEL is defined.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The information extracted from the device tree is now used to initialize
GPIO device instances. Up until now the GPIO device driver made no use
of this information. Actual instance creation is still controlled using
the Kconfig method. Missing GPIO device tree nodes were added in the
process for STM32L073, STM32F413 and STM32F373.
The information for gpio instance initialization has already been
present for supported STM32 SoCs but remained unused. Changes in the
device tree had no effect on GPIO functionality and was essentially
redundant. Using the device tree for hardware description seems
plausible and less painful than a myriad of defines in some SoC
description header.
The change was implemented under the assumption that current device
trees provide a correct description of the SoCs. Base register addresses
and RCC register bits were not explicitly checked for each device.
Manual tests were executed on:
- NUCLEO-F103RB
- STM32F429I-DISCO
- STM32F746G-DISCO
- NUCLEO-F767ZI
Manual tests consisted of blinky on different GPIOs and pins on each
board.
sanitycheck was executed for all STM32 based boards
Fixes: #10629
Signed-off-by: Martin Bertsche <martin72216@googlemail.com>
Update stm32f469i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
-Update yaml file
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f723e_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32f769i_disco configuration to match with
default configuration guidelines:
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update stm32l496g_disco configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update disco_l475_iot1 configuration to match with
default configuration guidelines:
-Deactivate features by default
-Configure available connectors
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Rename USB_{DBG,ERR,INF,WRN} into LOG_{DBG,ERR,INF,WRN}. This driver has
been missed from PR #11001 as it has been committed after.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Check for case where host == NULL but service != NULL
could have resulted later in a NULL dereference.
Coverity-CID: 189516
Fixes#11090
Signed-off-by: Gil Pitney <gil.pitney@linaro.org>
Use ARRAY_SIZE helper macro to compute size of array rather
than hardcoding.
Also, remove unnecessary variable to store the size which is
now useless.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Remove the redundant semicolon used as a terminator in
`if`, `switch`, `while` statements.
Found using Coccinelle.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
This patch adds a USB device driver for the USBHS device that can be
found on Atmel SAM E70 SoC family. Only the FIFO mode is supported
(as opposed to DMA). It supports LS, FS and HS modes, but defaults to
FS mode as Zephyr does not fully support HS mode yet.
Tested examples on an Atmel SMART SAM E70 Xplained Board:
* usb/cdc_acm
* usb/hid-mouse
* usb/mass
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
i2c_burst_read can fail during read/write procedure. Therefore,
add a sanity check for its return value.
Fixes#11101
Coverity-CID: 189505
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Add dts binding and info for TRNG device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add dts binding and info for RNGA device and enable basic support to
get the device name from DTS. We leave for now the base addresses
coming from the MCUX HAL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
If we have DTS support for an entropy driver we should get the name
generated from DTS ('label' property on the entropy device node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix RCOSC calibration initiation to ensure LF clock is
running; and the HF clock is running with crystal before
triggering the actual calibration in ISR.
Fixes#10811.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Convert gpio_cc32xx driver over to using device tree. Added binding
files, updates to dts for various SoCs that use cc32xx.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for LSM303DLHC accelerometer now supports API function
sensor_attr_set for attribute SENSOR_ATTR_SAMPLING_FREQUENCY.
Signed-off-by: Dennis Wildmark <d.wildmark@gmail.com>
Add basic 'lspci' command to list PCI devices. This command can be
enabled with the new Kconfig PCI_SHELL.
Example:
uart:~$ lspci
0:1 8086:7010 class: 0x1, 1, 4, I/O, addrs: 0xC000-0xC00F, IRQ -1
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If data is received before an IRQ handler was set and enabled,
hardware sets the ORE flag. Once set, the IRQ routine starts
hogging the CPU until ORE is cleared. This change will clear
the flag when user code attempts to drain incoming data.
Signed-off-by: Kiril Zyapkov <k.zyapkov@allterco.com>
Added bidirectional I2S support for Intel S1000
- Added implementation for I2S receive mode
- Extended driver instances to support 3 I2S ports
- Added DMA channel mappings for upto 4 I2S ports
- Utilized k_msgq to track buffers through the driver
- Allocate buffers for audio reception in the driver
- Free buffers after audio transmission in the driver
- Perform buffer reload for DMA after every reception/transmission
- Removed unused Kconfig variables
- I2S_CAVS_TX_BLOCK_COUNT
- I2S_CAVS_RX_BLOCK_COUNT
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Added a mechanism to refresh DMA buffers without the
need to call the "configure" API every time.
The reload is done after every DMA completion.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
k_poll_signal was being used by both, struct and function. Besides
this being extremely error prone it is also a MISRA-C violation.
Changing the function to contain a verb, since it performs an action
and the struct will be a noun. This pattern must be formalized and
followed and across the project.
MISRA-C rules 5.7 and 5.9
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Since CCOMPARE* registers have undefined values after reset,
set compare value first before enabling timer interrupt.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
