Remove HTS221 sensor support from sensortile_box_pro as it has been ruled
out from final version. In fact, HTS221 is in the process of being
terminated and is not recommended for new design. The candidate replacement
is SHT40 from Sensirion, which is available also as a DIL24 adapter, which
can be plugged on sensortile_box_pro board.
See SENSEVAL-SHT4XV1:
https://www.st.com/en/partner-products-and-services/senseval-sht4xv1.html
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The documentation does not provide any guides on how to configure
the MCO pin, and responsebility is given to the application.
Signed-off-by: Joakim Andersson <joerchan@gmail.com>
`checkpatch.pl` requires that dts sources are indented with tabs,
fix all the spaces that slipped in while checkpatch wasn't watching.
Signed-off-by: Jordan Yates <jordan@embeint.com>
Uart FIFO is useful in case of wakeup on serial as it will allow
to avoid losing chars.
Enable it systematically on all overlays for this sample.
Signed-off-by: Erwan Gouriou <erwan.gouriou@st.com>
Simple blinky example, but using STOP3 mode. When in STOP3 mode,
GPIOs are not driven, but only pull-up or pull-down can be enabled
based on value in PWR registers.
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
The gpio pin that will be used as a source for PWR wake-up pins does not
actually need to be configured as input, hence input_gpio_keys driver does
not need to be involved. As far as GPIO controller is concerned, the pin
can be in analog state.
Also, it's clearer & safer to call gpio_pin_configure_dt directly in the
application with the STM32_GPIO_WKUP flag, just before calling Poweroff,
instead of relying on a driver, like input_gpio_keys to do it just after
boot behind the scenes, & risk not having the correct wake-up pins config
when Poweroff is finally called.
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Change source tree organization for Synopsys nSIM platform.
Classical ARC architectures arc_v2 arc_v3 moved to arc_classic
SoC and boards family.
nSIM SoCs were separated regarding series: EM, HS, SEM, VPX2.
This PR sould be seeing as the preparation for
addition new nSIM platform based on the RISC-V architecture.
Signed-off-by: Nikolay Agishev <agishev@synopsys.com>
This sample reports the I2C configuration of the selected I2C node
from the board DTS : bitrate property of the I2C node
In case of I2C V2, it also gives the TIMINGS which has to be written
in the DTS <timings> property of the I2C V2 node.
Uses the i2c_get_config function with CONFIG_I2C_STM32_V2_TIMING.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
I also added an overlay file for the nucleo_h563zi board to the
samples/boards/stm32/backup_sram example.
Signed-off-by: Thorsten Spätling <thorsten.spaetling@vierling.de>
Introduce a sample for BlueNRG-based devices to support interaction with
ST BlueNRG GUI application based on U(S)ART protocol.
Signed-off-by: Ali Hozhabri <ali.hozhabri@st.com>
This sample demonstrates how gpio pins can be used to power on
the system after a Poweroff, just like a reset pin.
The user only needs to add the STM32_GPIO_WKUP flag to the gpio pin
in "gpios" property of a DT device such a button or a sensor.
The samples Powers off the system after a delay then the user can power it
on with the user button that has the STM32_GPIO_WKUP flag in DT.
Only works on STM32 boards that support Zephyr POWEROFF
(U5, WL, WB, & L4 SoC series), & also have a user button whose GPIO pin
is associated with a wake-up pin (see PWR node in SoC dtsi file).
Signed-off-by: Abderrahmane Jarmouni <abderrahmane.jarmouni-ext@st.com>
Changes twister tests and nrf samples from using legacy adv to ext adv
since this is the default for Mesh. Legacy adv is still tested in bsim.
Removes redundant test configuration testing ext adv.
Removes redundant config for ext_adv in `multi_ext_adv.conf`.
Signed-off-by: Håvard Reierstad <haavard.reierstad@nordicsemi.no>
This WDT is responsible for monitoring the external
32.728 Hz crystal connected to pins XTAL_32K_P and
XTAL_32K_N. If an oscillation failure is detected
the hardware automatically switch to RTC_RC_SLOW
clock source and triggers an interrupt.
Signed-off-by: Lucas Tamborrino <lucas.tamborrino@espressif.com>
This patch removes all uses of the adv auto-resume feature in the
Bluetooth samples. The auto-resume feature is planned for deprecation.
Samples that are not intended to demonstrate a technique to do with
re-connection simply do not restart the advertiser, in interest of
simplicity. The user is expected to reboot the sample when needed.
Signed-off-by: Aleksander Wasaznik <aleksander.wasaznik@nordicsemi.no>
Pins P0.06 and P0.07 are shorted on nRF5340 DKs prepared for on-target
tests because that is required for UART tests. That causes background
SPIM transfers in this sample to fail because SPIM is not able to drive
its SCK line configured as P0.06. Rearrange then the pins used in this
sample, so that SCK is not on a pin involved in a GPIO loopback.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
This board includes three gpio-connected LEDs and push-buttons. Include
all missing defines in board's DTS and while at it, fix existing button
definition (missing pull-up enable) and align node names with other
boards (e.g. 'nucleo_wb55rg').
Provided changes were tested on real board with 'blinky' and 'button'
samples.
Additionally, duplicated LED nodes no longer required were removed from
overlay file for this board, in 'suspend_to_ram' sample.
Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
The naming of these two options was problematic, since it's both of them
are about vendor extensions, even though one has _EXT in the name and
the other doesn't. Just merge one option into the other. This has a
slight overhead on the controller side of enabling some more vendor
features if BT_HCI_VS is enabled, but that should hopefully be
acceptable.
Signed-off-by: Johan Hedberg <johan.hedberg@gmail.com>
Removed Harness's repeat field.
Added to schemas in e722db14ad,
together with the rest of harness_config.
Added to Harness when it was created.
Now present only in one sample -
mec15xxevb_assy6853 power management sample.
Could not find definitive proof whether it has ever been used.
Signed-off-by: Lukasz Mrugala <lukaszx.mrugala@intel.com>
There are several esp32-based boards that its conf and overlay
files are missing proper renaming to match cpu cluster.
This also removes all _SOC_ name from files.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
The advertiser options to automatically add the name in the scan
response and the advertising data will be deprecated.
Update the samples that were using those options by explicitly adding
the device name in the advertising data or the scan response data.
Signed-off-by: Théo Battrel <theo.battrel@nordicsemi.no>
Board specific sample that only works with certain revisions of the
hardware requiring special BIOS settings.
Fixes#58057
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add handling of SCK initial value based on the SPI mode used.
If mode is using CPOL then SCK needs to be set.
Fixes: #71154
Signed-off-by: Joakim Andersson <joakim.andersson@heimdallpower.com>
Fix setting of sample frequency.
The nrfx drivers are now using raw integere values instead of nrf
definitions.
Fixes: #71154
Signed-off-by: Joakim Andersson <joakim.andersson@heimdallpower.com>
The commit adds dependency on Kconfig FLASH_PAGE_LAYOUT to subsystems
that really require it:
FCB, NVS, LittleFS
and removes direct selection from '*.conf' files where no longer
needed.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Adjustments of overlay and conf files to adjust for the MERGE removal.
The revert of MERGE requires specific overlay and conf files for boards
which relied on the MERGE feature.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
LPTIM4 is selected, since it is used only for internal timing
and it doesn't support output/input
Signed-off-by: Adam Berlinger <adam.berlinger@st.com>
Adds missing sample.yaml file.
Update some sample.yaml to include build_only
Update some sample.yaml for device testing.
Signed-off-by: Sylvio Alves <sylvio.alves@espressif.com>
After https://github.com/zephyrproject-rtos/zephyr/pull/70438
got merged simultaneously with
https://github.com/zephyrproject-rtos/zephyr/pull/70564
all these tests stopped building properly due to the
change of avaliable variables in Kconfig & cmake.
Let's fix them.
As a bonus, as for kconfig the BOARD_TARGET_STRING is the
same for the hwmv1 backwards compatible name, let's
just remove the check for the old names.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Replace all instances of
nrf5340bsim_nrf5340_cpunet & nrf5340bsim_nrf5340_cpuapp
with
nrf5340bsim/nrf5340/cpunet & nrf5340bsim/nrf5340/cpuapp
In these samples/tests twister yamls definitions.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Replace the uses of the hwmv1 names in the samples documentation
with the corresponding hwmv2 ones.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
For all samples which handle the nrf5340bsim in some special way
(for example in sysbuild files, or by checking what samples are
supported) handle also building with the hwmv2 names.
Also, let's fix the cmake info message in these respective
samples which tells the user which board target is used for which
part of the app.
Signed-off-by: Alberto Escolar Piedras <alberto.escolar.piedras@nordicsemi.no>
Update all usages of the MBOX API to the latest API changes (to be
squashed for bisectability).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
