Now that the samples use DT generated defines we can remove the
hexiwear_k64 specific ones in board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the Red, Green, & Blue PWM LED info to the device tree. We will use
this in the future for any samples that utilize PWM on these LEDs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
No need to check for BT being enabled. The UART entries will be
available for use if BT is enabled and will do nothing if not.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The wncm14a2a modem is an add-on/shield and not part of the frdm_k64f
board and should be maintained and configured outside of the board.
This needs to be moved to a shield, see #10965.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Adding watchdog driver for sam SoC. The current implemntation just
diables the watchdog on device boot.
This PR adds the following support for SAM3X, SAM4S and SAME70
1. Activate processor reset
2. Activate all reset
3. Generate interrupt on watchdog timer expiration.
Signed-off-by: Subramanian Meenakshi Sundaram <subbu147@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Since the mb_display driver is specific to the microbit we can move
the GPIO pin defines from board.h into the driver. This lets us remove
one of the few remaining drivers that is including board.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the GPIO info for the buttons into the dts, this lets us match what
all other boards are doing. Update some sample & test code to use the
dts generated SW0_GPIO_CONTROLLER define instead of SW0_GPIO_NAME.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Remove some references <board.h> that aren't need or replace them with
<soc.h> where that is the proper include to pull in. Also use "board.h"
instead of <board.h> for how we include the file when its local to the
board code itself.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The frdm_k64f and mimxrt1050_evk boards do not have native bluetooth
support, but rather require an arduino shield to supply a ble controller
over serial hci. Convert the dts to use the newly introduced frdm_kw41z
ble controller shield.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The EFR32™ Mighty Gecko Starter Kit EFR32MG-SLTB004A (a.k.a
Thunderboard Sense 2) contains a MCU from the EFR32MG12P family built
on ARM® Cortex®-M4F processor with low power capabilities.
There is an On-Board J-Link Debugger that presents a virtual COM port
for general purpose application serial data transfer with this
interface and a Mass Storage for firmware flashing.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Combines the lpcxpresso54114_m4 and lpcxpresso54114_m0 boards into one
directory containing both board configurations. This eliminates some
duplicate code and documentation, and better represents the actual
hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
In an effort to reduce the number of CONFIG_ defines in dts files, we
can remove CONFIG_MCUMGR_SMP_UART and just always set
'zephyr,uart-mcumgr' as there is no harm to always having this set for
those board dts files that define the property.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There were several issues in the dts binding for the ssd1673 display:
* binding file mixed description & generation up together
* Use of BASE_LABEL
* orientation-flipped should have been of type boolean
Update the binding file to reflect these changes, and made associated
changes to dts_fixup.h and driver as needed.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Flashing the board as described in the docs does not work without having
proper udev rules set. Add documentation for setting those.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add a link to the reel board product page at PHYTEC to help people in
locating schematics, etc.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Added support for SPI 1 available from the arduino connector (plus an
extra gpio). Tested against samples/sensor/bme280.
Signed-off-by: AJ Palmer <ajpcode@hotmail.com>
The Adafruit Feather nRF52 does not have any RTS/CTS signal
connections between the nRF52832 and the on-board CP2104 USB/UART
bridge. Pins 5 and 7 are regular GPIOs.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
This enables I2C, SPI, PWM, RTC and USB.
RTC tested on samples/drivers/rtc
USB tested on samples/subsys/usb/cdc_acm
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Add support for ST Micro Nucleo-64 board with the STM32F302R8
processor. nucleo_f429zi and nucleo_f334r8 were used as
references.
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Introduces the location property and adds the ability to use values
generated by the device tree configuration.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The config file sourced in openocd.cfg is the nuclean_f3 one instead of the one for
the stm32373c.
This makes it impossible to flash the stm32373c evaluation board rev.B:
Error: open failed
in procedure 'init'
in procedure 'ocd_bouncer'
error: command exited with status 1:
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/bin/openocd -s
/opt/zephyr-sdk/sysroots/x86_64-pokysdk-linux/usr/share/openocd/scripts
-f
/home/maudat/repo_upstream/zephyr/boards/arm/stm32373c_eval/support/openocd.cfg
-c init -c targets -c 'reset halt' -c 'flash write_image erase
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset halt' -c 'verify_image
/home/maudat/repo_upstream/zephyr/samples/basic/blinky/build/zephyr/zephyr.bin
0x8000000' -c 'reset run' -c shutdown
Replace the file sourced by stm32f3discovery.cfg to flash successfully.
Signed-off-by: Mathieu Audat <mathieu.audat@savoirfairelinux.com>
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
Add sample application for LSM303DLHC, ST MEMS
system-in-package featuring a 3D digital linear
acceleration sensor and a 3D digital magnetic
sensor.
Enable sample to build on stm32f3_disco board
during sanitycheck.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Enable LSM303DLHC, ST MEMS system-in-package featuring
a 3D digital linear acceleration sensor and a 3D digital
magnetic sensor, on stm32f3_disco board.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
