Since Voltage Reference block is not supported, the ADC does not work
properly on FRDM-KW41Z. Set voltage reference to alternate source
in frdm_kw41z_defconfig.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
We had SEGGER support enabled by default previously, but the new
Kconfig option CONFIG_USE_SEGGER_RTT needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The lpcxpresso54114_m0 tends to be the secondary core so doesn't
typically have a UART setup for it. We had SEGGER support enabled by
default previously, but the new Kconfig option CONFIG_USE_SEGGER_RTT
needs to be set as well now.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support for 96Boards STM32 Sensor Mezzanine board. This board
is one of the 96Boards Mezzanine board which can work standalone or on
top of the 96Boards Consumer Edition boards.
Below are some of the key features of this board:
1. STM32F446VE MCU
2. 96Boards high/low-speed connectivity
3. Arduino™ Uno revision 3 and Grove connectivity
4. Integrated MEMS sensors:
1. LSM6DS3H
2. LIS3MDL
3. LPS22HB
4. MP34DT01-M
5. On-board ST-LINK/V2-1 debugger/programmer
More information about this board can be found in the 96Boards product
page: https://www.96boards.org/documentation/mezzanine/stm32/
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
The 0.9.5 SDK has support for the Cypress PSoC6 family. Add ablilty to
flash with openocd. I've only tested flashing hello_world on the m0.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To enable the QSPI you have to physically modify the board and this
disables the hyperflash. Since we plan on removing Kconfig from device
trees, its easier to treat the QSPI flash as a seperate board config and
thus it will get a dts to match.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This driver introduces an emulated LCD display for the native POSIX
board. The emulated display driver makes use of SDL2 to render the
displays frame buffer into a dedicated desktop window.
Signed-off-by: Jan Van Winkel <jan.van_winkel@dxplore.eu>
Zephyr SDK 0.9.4 added OpenOCD support for SiLabs EFR32FG1P SoC. This
commit updates 'Flashing' paragraph of the board documentation to
reflect this change.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Fixes broken user guide and schematics links in nxp board documentation.
Updates remaining nxp.com links from http to https.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Connectors imaages for nucleo_f413zh were actually a reuse of
similar board nucleo_f412zg.
Add dedicated images for nucleo_f413zh.
Fixes#5198
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
'make flash' always erase the flash banks from sector 0, and flashing
the Zephyr.bin file to base address of flash even if there has a
bootloader placed on the first sector.
Users maybe want placed Zephyr to another location instead of sector
0 by adding 'zephyr,code-partition' in dts. But the openocd scripts
doesn't deal with that currently.
Fix this issue, flash zephyr.elf instead of zephyr.bin, elf file
contain load address and openocd scripts can deal with it.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
Now that we can support the same compatible but different bus types,
update the LSM6DSL support to utilize the same compatible for either I2C
or SPI. We rename the i2c binding file to st,lsm6dsl-i2c.yaml just to
be a bit more clear.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Removed Console dependencies from shell uart backend.
Generated define: CONFIG_UART_SHELL_ON_DEV_NAME for each board.
Fixes#10191
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
In commit d8e3ea6bc2
the LF clock interrupt was enabled, which causes its interrupt
handler to be used. This interrupt handler interacts with the
NRF_POWER registers.
Therefore require using the newer HW models which include a stub
of this registers.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
CONFIG_TEXT_SECTION_OFFSET allows the entire image to be moved
in memory to allow space for some type of header. The mcubootloader
can boot only such images which reserve some space for the header.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
This patch enables the UART_INTERRUPT_DRIVEN by default for
colibri_imx7d_m4, udoo_neo_full_m4 and warp7_m4 boards.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
Reel Board doesn't enable BT by default like many of the nRF52
boards do. So let's make enabling BT a bit easier, by selecting
the BT_CTLR config when BT is enabled. This allows a sample
overlay to merely set:
CONFIG_BT=y
And the end result should be close to correct.
Signed-off-by: Michael Scott <mike@foundries.io>
The nRF51822 and nRF52832 does not support 802.15.4, so remove this
statement from documentation.
Signed-off-by: Stig Bjørlykke <stig.bjorlykke@nordicsemi.no>
Modify board stm32_min_dev aka "blue pill" led pin assignment in dts
from PB12 to PC13.
This board has a user led connected to PC13.
Sample blinky and similar would run out-of-box without additional
circuit to readout PB12 level.
Tested blinky on corresponding board.
Signed-off-by: Stephen Yi <stephen.jin.yee@gmail.com>
"-machine type=pc-0.14" appears to be the option which leads to
broken PCI emulation in QEMU, where PCI enumeration reports one
IRQ number (11), while actually IRQ 10 is emulated by QEMU.
"-vga none" and "-display none" appear to be just subordinate of
"-machine type=pc-0.14" and are required to get qemu_x86 into
bootable state.
Fixes: #11706
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
There are different interrupt numbers for R22 v R23. Before this was
being handled via using Kconfig symbol CONFIG_BOARD_EM_STARTERKIT_R23 in
emsk_dt.h. Since we want to remove use of Kconfig in dts we handle this
via different dtsi files and having the proper one included by the
proper board revision dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Towards removing Kconfig from DTS we need to move setting of the sizes
of ICCM/DCCM into the SoC specific DTS files and out of emsk_dt.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Including Bluetooth to every project unnecessary increase size of the
project, for example hello world sizes:
Memory region Used Size Region Size %age Used
FLASH: 48492 B 1 MB 4.62%
SRAM: 11236 B 256 KB 4.29%
IDT_LIST: 136 B 2 KB 6.64%
after the patch:
Memory region Used Size Region Size %age Used
FLASH: 13344 B 1 MB 1.27%
SRAM: 4004 B 256 KB 1.53%
IDT_LIST: 72 B 2 KB 3.52%
3+ times difference.
PS: It also crashes when 802.15.4 enabled.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add documentation for the quark_se_c1000_devboard with links to platform
guidelines and other details.
Fixes#11166
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Added description how to build, programm and see console output of
hello_world example on cy8ckit_062_wifi_bt_m0 board.
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
The EFM32 Pearl Gecko Starter Kit contains sensors and
peripherals demonstrating the usage of the EFM32PG MCU
family. This patch adds basic support for this board
and is copied from EFM32WG-STK3800.
Signed-off-by: Gil Benkö <gil.benkoe@pm.me>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Adds support for debugging and flashing the mimxrt1050_evk board via
pyocd. Support for this board has not yet been merged in upstream pyocd,
therefore the default in zephyr is left as jlink.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Merge up_squared_dts_fixup.h and up_squared_sbl_dts_fixup.h into
dts_fixup.h. This allows us to remove BOARD_DIR from being included
everywhere.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
