The Silicon Labs EFM32 Happy Gecko MCU includes:
* Cortex-M0+ core at 24MHz
* Up to 64KB of flash and 8KB of RAM
* Full speed (12 MHz) USB 2.0 Device
* Multiple low power peripherals
Signed-off-by: Marcio Montenegro <mtuxpe@gmail.com>
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Convert over arc based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This will be usefull to tell when Ethernet device has its attributes
filled in by DTS rather than by Kconfig.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Convert gpio_gecko driver over to using device tree. Added binding
files, updates to dts for various SoCs that use gpio_gecko.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add maximum-speed property to usb nodes and set it to
their maximum on-chip PHY capability.
SoCs with USB device controllers only support full
speed, so we don't add maximum-speed to these nodes.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Add maximum-speed property to usb node.
It configures USB controllers to work up to a specific speed.
Valid arguments are "super-speed", "high-speed", "full-speed"
and "low-speed".
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
Convert over x86 based boards to use device tree instead of board.h to
describe buttons & LEDs. There are a few boards that the button gpio
flags need validation.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the missing bits to the yaml, dts, and Kconfig to enable GPIO pin
generation based on device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The gpio controllers on SAM4S, SAME70, and SAMD were missing properties
related to GPIO pin generation. Add the missing details into the yaml
and dts files to allow boards to specific gpio pins.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add the needed bits to get device tree support for the GPIO controller
on the Zedboard-Pulpino. This will allow us to move LED & button info
into the board.dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add simple device tree support for the Pulpino SoC and Zedboard-Pulpino
board port. This gets the UART info from device tree instead of soc.h
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
added sam4s16b, sam4s8c, sam4s8b, sam4s4c, sam4s4b,
sam4s4a, sam4s2c, sam4s2b and sam4s2a.
Used the same order as in the data sheet and code structure
equal to same70. Updated the sam4s_xplained board to match
the altered .dtsi location of the specific SoC.
Signed-off-by: Vincent van der Locht <vincent@vlotech.nl>
This patch adds timers and PWM nodes to STM32 F7 series, as well as the
corresponding dts fixup entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_PINS and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled gpio drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_GPIO_DEVICE and
HAS_DTS_GPIO.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled spi drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_SPI_DEVICE and
HAS_DTS_SPI.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Every board that uses dts-enabled i2c drivers has a board-level dts, so
there is no need to have separate configs HAS_DTS_I2C_DEVICE and
HAS_DTS_I2C.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Now that we've cleaned up all the STM32 related .dtsi files we don't
use dts/arm/st/mem.h so we can remove it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F7 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F3 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F2 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Makes the designware spi driver consistent with other spi drivers by
selecting HAS_DTS_SPI in the driver. This required adding spi nodes and
dts fixups to several arc and x86 socs, as well as enabling those nodes
in associated boards.
Also refactors the driver to use the base address, interrupt number, and
interrupt priority from dts.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L4 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the L0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F1 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. We also seperate
out the F0 dtsi files into their own dir.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Adding i2c slave requires overlay with node definitions and
proper aliases depending on driver implementation.
Modified i2c_slave_api test to use information from dts.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Added basic PSoC6 UART driver and added two UART nodes in the PSoC6
device tree to have output from CM0+ and CM4 cores.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
Added initial support and created the corresponding device tree part for
building PSoC6 SoC as part of Zephyr.
Signed-off-by: Nazar Chornenkyy <nazar.chornenkyy@cypress.com>
Signed-off-by: Oleg Kapshii <oleg.kapshii@cypress.com>
Commit introduces support for ARM TrustZone CryptoCell 310
for Nordic Semiconductor nRF SoCs in device tree.
Signed-off-by: Dominik Kilian <Dominik.Kilian@nordicsemi.no>
Enable UART 16550 driver for Nios-II QEMU platform.
Note: This PR is tested with patched version Qemu 3.0.0 which
adds support for altera_10m50_zephyr machine type.
Signed-off-by: Ramakrishna Pallala <ramakrishna.pallala@intel.com>
'use-prop-name' is not documented.
Update dts/bindings/device_node.yaml.template to fix this.
Document that 'type' attribute is not used.
Fixes#9971
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Flash controller-node for stm32f2 based SoCs was missing basic
properties such as compatible, labeln reg and interrupts.
Fix this and add matching yaml binding file;
Fixes#10057
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
When we fixed the missing reg property in the cpu node, we forgot to
add #address-cells & #size-cells for the node.
This fix the following warnings we get:
Warning (reg_format): "reg" property in /cpus/cpu@0 has invalid
length (4 bytes) (#address-cells == 2, #size-cells == 1)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This change aims at fixing 'unit_address_vs_reg' warning in
stm32 *-pinctrl.dtsi files.
This warning pops up when a node name is made up with an address
(node_name@xx) but does not contain a reg property.
This case was encountered for led nodes for instance,
where a reg property has no meaning.
Fix this by changing node_name@xx to node_name_xx which removes the
guilty '@xx' syntax but preserves node_name uniqueness.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /soc/virtualcom@0:
node has a unit name, but no reg property
Fix by dropping the unit address from the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /flash: node has a reg or ranges
property, but no unit name
or
Warning (unit_address_vs_reg): /memory: node has a reg or ranges
property, but no unit name
Fix by adding unit address that is missing to flash & memory nodes.
Additionally the Silabs memory nodes didn't have a compatiable or
device_type, so add those properties as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/cpu@0: node has a
unit name, but no reg property
Fix by adding reg property to missing cpu nodes.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_vs_reg): /cpus/arcv2-intc@0:
node has a unit name, but no reg property
Fix by removing the unit address from the nodes. Some cases we had a
reg property and a unit address for such interrupt controllers, in those
cases remove both the reg & unit address in the node name.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
We get several warnings of the form:
Warning (unit_address_format): /soc/uart@000003f8:
unit name should not have leading 0s
Fix these by remove the leading 0s.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_NRF51822_QFAA
CONFIG_SOC_NRF51822_QFAB
CONFIG_SOC_NRF51822_QFAC
CONFIG_SOC_NRF52810_QFAA
CONFIG_SOC_NRF52832_QFAA
CONFIG_SOC_NRF52832_CIAA
CONFIG_SOC_NRF52832_QFAB
CONFIG_SOC_NRF52840_QIAA
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_SAME70*
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now that we have a common DT_SIZE_K macro use it instead of defining
__SIZE_K eveywhere. We also have DT_SIZE_M, so use that in a few
places as well.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The RTC node for some reason was setting #address-cells and #size-cells.
However it has no children so there isn't really any reason to do this.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
In case of out of tree SoC, mem.h will trigger and error since
it is not aware of new SoC CONFIG_SOC_<reference>.
Modify error condition in order to generate the error only if
the flash and error size are not defined at this point (even in
out of tree case).
Fixes#9978
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_PART_NUMBER_EFM32WG990F256
CONFIG_SOC_PART_NUMBER_EFR32FG1P133F256GM48
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
To move forward and remove use of Kconfig in dts files lets just create
SoC specific dtsi files that the boards can include. This lets us
remove:
CONFIG_SOC_CC3220SF
CONFIG_SOC_MSP432P401R
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add 'generation: define' directive to 'compatible' property.
When existing for a type of device, move compatible property
description in device base structure (eg: i2c.yaml)
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
All flash controllers have a mandatory compatible property.
Add it to the generic binding that is included by all.
Signed-off-by: Bobby Noelte <b0661n0e17e@gmail.com>
UART pins (TX, RX, RTS, CTS) are now configured in DTS files.
RTS and CTS definitions are optional. If flow control is enabled
and RTS/CTS pins are not defined, then compiler will issue
an error message.
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
The LEDs, buttons and necessary aliases are now configured via dts.
This commit breaks the sample under samples/boards/nrf52/power_mgr.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
According to Device Tree specification, previously
defined nodes may be deleted with the followin
syntax:
/delete-node/ node-name;
or
/delete-node/ &label;
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This change adds DTS definition of SPI device for nRF chips.
It also removes SPI pin configuration from Kconfig and moves it to
chip DTS.
Signed-off-by: Filip Kubicz <filip.kubicz@nordicsemi.no>
This commit adds ADC nodes to DTS files for nRF SoCs and introduces
corresponding bindings for these nodes.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The whole STM32L4 family has a flash with a constant page size of 2kB.
Specify this value in the DTS as the nvs sample application pull it
from there.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The nvs sample assumed a 1 KB flash erase block size, which caused the
sample to fail on frdm_k64f because its erase block size is 4 KB. Get
the erase block size from dts instead.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Add support for TI LP5562 I2C 4-channel LED driver.
Supported blinking period: 1ms - 1000ms
Supported brightness value: 0% - 100%
This driver supports the entire currently available API.
Signed-off-by: Johannes Hutter <johannes@proglove.de>
Add support for usbotg_fs, by adding the DT fixup, pinmux macros,
and the DT entries in stm32f2.dtsi.
Signed-off-by: Istvan Bisz <istvan.bisz@t-online.hu>
The L433 chip is a superset of the L432, just grabbing a few additional
interfaces (LCD, I2C2, USART3, SPI2, SDMMC). All the support/HAL files
are already there, so enabling these is just a matter of build system
setup.
Tested on an application specific board (builds correctly and I2C2
works.) I unfortunately don't have a nucleo/discovery board to create a
reference board for.
Signed-off-by: David Lamparter <equinox@diac24.net>
This patch adds the RDC (Resource Domain Controller) peripheral
permissions settings for the i.MX applications cores (Cortex A9 on
i.MX6 and Cortex A7 on i.MX7).
This will enable both Linux (on application's core) and Zephyr (on M4
core) to share the peripherals and coexist.
The settings are defined at devicetree level and applied in the soc.c.
A complete solution should involve the SEMA4 to control the peripherals
access and prevent resource deadlocking and misusage.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The WNC-M14A2A (LTE / LTE-M) modem is presented as an Arduino-
compatible shield via AT&T's IoT Starter Kit v1.0. It was
originally intended to work with the FRDM-K64F board, but
in theory as long as the right pins are configured it can
work with any board that supports Arduino-compatible headers.
The driver utilizes the CONFIG_NET_OFFLOAD setting to avoid the
normal handling of IP packets, and instead uses a socket-like
UART interface to handle incoming and outgoing data.
Signed-off-by: Michael Scott <mike@foundries.io>
Only basic features supported initially but more could be added from:
https://www.nxp.com/docs/en/data-sheet/MMA8451Q.pdffixes#9006
A sample app will be provided in a separate PR.
Signed-off-by: Lars Knudsen <larsgk@gmail.com>
The STM32F7 uses the V2 version of the STM32 I2C controller. Add the
corresponding Kconfig, DTS, DTS fixup and pinmux entries.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit adds support for the nrf52840_pca10059 board.
The flash partitions are configured to allow migrating from
the stock bootloader to MCUBoot.
Signed-off-by: Emanuele Di Santo <emdi@nordicsemi.no>
This adds the SoC configuration for Apollo Lake. This is based
on the Atom configuration.
Origin: Original
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
After running some tests which enable assert macro I found some issues
with the i.MX UART configuration.
This patch configures the Tx Fifo Watermark and Modem Mode accordingly.
Signed-off-by: Diego Sueiro <diego.sueiro@gmail.com>
The common spi.yaml defines an optional clocks property that can be
overridden by specific spi driver bindings to be required. The
description and generation attributes are duplicated.
This fixes build warnings:
extract_dts_includes.py: Merge of 'description': 'Clock gate control
information' overwrites 'Clock gate information'.
extract_dts_includes.py: Merge of 'generation': 'structures' overwrites
'define'.
And introduces a different build warning, which is intended behavior:
extract_dts_includes.py: Merge of 'category': 'required' overwrites
'optional'.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The common uart.yaml defines an optional clocks property that can be
overridden by specific serial driver bindings to be required. The
description and generation attributes are duplicated.
This fixes build warnings:
extract_dts_includes.py: Merge of 'description': 'Clock gate control
information' overwrites 'Clock gate information'.
extract_dts_includes.py: Merge of 'generation': 'structures' overwrites
'define'.
And introduces a different build warning, which is intended behavior:
extract_dts_includes.py: Merge of 'category': 'required' overwrites
'optional'.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
This patch adds support for the Analog Devices ADT7420 High-Accuracy
16-bit Digital I2C Temperature Sensors. Optionally sensor threshold
events are supported.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
The STM32F7 uses the same USB OTG FS controller than the STM32F4 series.
It is therefore trivial to add support for it, by adding the DT fixup
and pinmux macros, and the DT entries in stm32f7.dtsi. Keep it disabled,
it should be enabled at the board level.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
samd21.dtsi includes now the same content need for SAMD20,
move it to samd.dtsi and include it from samd21.dtsi.
Then later USB support can be added to the samd21.dtsi seperatly
from the samd20 etc.
Signed-off-by: Sean Nyekjaer <sean@nyekjaer.dk>
The EFR32 Flex Gecko Wireless Starter Kit contains sensors and
peripherals demonstarting the usage of the EFR32FG1P SoC
family. This patch add basic support for this board.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
Since the UART0 @ 0x40002000 can either be UART or UARTE the user of the
soc.dtsi needs to select either compatible = "nordic,nrf-uarte" or
"nordic,nrf-uart"
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The STM32F769 has more interrupts and features than the STM32F746,
but the basic support is similar with STM32F746
Signed-off-by: Yong Jin <jinyong.iot@foxmail.com>
The nvic yaml files were missing an id property. So we'd get a warning
like:
extract_dts_includes.py: 'id' property missing in 'ARMv7-M NVIC Interrupt Controller' binding. Using '<unknown id>
Add the id to fix this warning.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
clear RXNE flag in fifo_read, remove TEACK and REACK
check when uart_stm32_init because stm32f2 doesn't
has those flags.
Signed-off-by: qianfan Zhao <qianfanguijin@163.com>
The STM32F723 has more interrupts than the STM32F746 due to the
additional SDMMC controller. Besides that the changes are very
similar to the ones of the STM32F746.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Add support for NXP PCA9633 an I2C 4-bit LED driver.
Supported blinkink period: 41ms to 10667ms
Supported brightness value: 0 to 100%
This driver supports the following APIs:
1. led_blink
2. led_set_brightness
3. led_on
4. led_off
Signed-off-by: Sebastien Bourdelin <sebastien.bourdelin@savoirfairelinux.com>
This patch includes:
STM32F7 family device tree file with basic and UART definitions.
STM32F746 subfamily device tree file.
Memory definitions for STM32F746xG subfamily.
Signed-off-by: Yurii Hamann <yurii@hamann.site>
STM32F412/413/446/469 SoCs have 6 bidirectional endpoints
according to the reference manuals RM0402, RM0430,
RM0390 and RM0386.
Signed-off-by: Yannis Damigos <giannis.damigos@gmail.com>
This commit moves the definitions for the LED and Buttons
supported in nrf52810_pca10040 DK in DTS from board.h. Aliases
are kept in board.h to make basic examples pass.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nRF52810 is a low-cost variant of the nRF52832, with a reduced set
of peripherals and memory. This commit adds basic support for it in the
arch SoC and dts folders.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <ioannis.glaropoulos@nordicsemi.no>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
SDA and SCL pins can now be configured through DTS.
Pins on development kits have been assigned according to arduino
headers.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
The i.MX 6SoloX SoC is a hybrid multi-core processor composed by one
Cortex A9 core and one Cortex M4 core.
Zephyr was ported to run on the M4 core. In a later release, it will
also communicate with the A9 core (running Linux) via RPMsg.
The low level drivers come from NXP FreeRTOS BSP and are located at
ext/hal/nxp/imx. More details can be found at ext/hal/nxp/imx/README
The A9 core is responsible to load the M4 binary application into the
RAM, put the M4 in reset, set the M4 Program Counter and Stack Pointer,
and get the M4 out of reset.
The A9 can perform these steps at bootloader level after the Linux
system has booted.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
The various STM32 reference manuals sometimes define the USB endpoints
as IN or OUT only and sometimes as bidirectional, even in the same
manual. This is likely because the OTG implementation has one set of
registers for the IN endpoints and one other set for OUT endpoints.
However at the end a given endpoint address can both transmit and
receive data.
This causes some confusion how to declare the endpoints in the device
tree, and depending on the SoC, they are either the same number of IN
and OUT endpoints declared, or they are declared as bidirectional. At
the end it doesn't really matter given how the driver uses those values:
#define NUM_IN_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_IN_ENDPOINTS)
#define NUM_OUT_EP (CONFIG_USB_NUM_BIDIR_ENDPOINTS + \
CONFIG_USB_NUM_OUT_ENDPOINTS)
#define NUM_BIDIR_EP NUM_OUT_EP
This patch therefore cleanup the driver, the DTS, and the DTS fixups to
only define the number of bidirectional endpoints.
In addition to the cleanup, that fixes a regression introduced by commit
52eacf16a2 ("driver: usb: add check for endpoint capabilities"), which
introduced a wrong check for SoC only defining the number of
bidirectional endpoints.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This commit enables CAN on the STM32L432.
Tested on nucleo l432ck with external transceiver and loopback mode.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This commit splits the common interrupt into rx and tx parts because
only STM32F0 series has a common interrupt.
Moved clock source definition to device-tree.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
The prepended 0x causes DTC warnings and shouldn't be there.
Tested by compiling hello_world for nrf52840_pca10056 before and after.
Fixes#8334.
Signed-off-by: Alex Tereschenko <alext.mkrs@gmail.com>
This adds basic support for declaring gpio nodes in dts for nrf52.
The dts.fixup provides mapping for the generated defines to the config
defines currently used by the nrf gpio driver.
Existing boards that use nrf52 are updated.
Signed-off-by: Marc Reilly <marc@cpdesign.com.au>
IRQ priorities for CAVS and DW were previously defined in Kconfig.
They are now defined via DTS and removed from Kconfig.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
