Refactors the mcux lpsci driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux uart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from kinetis socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following update of stm32wb package, FLASH_FLAG_SR_ERROR
has been renamed to FLASH_FLAG_SR_ERRORS.
Update driver to fix compilation issue.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
The firmware version on the CCS811 on nrf52_pca20020 is generally
version 1.1, which does not set the data ready bit in the status
register. Assume that a non-zero CO2 measurement on that version is
fresh for the purposes of determining the fetch status.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The application may want to know the configured mode without inspecting
Kconfig macros; this is important for proper management of BASELINE
which is mode-dependent.
It also may need to know the version of the hardware and firmware, as
the behavior of application firmware 2.0 is significantly better than
version 1.1.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This mode is documented as producing a raw result every 250 ms that the
application must convert to eCO2 and eTVOC readings. In practice
application firmware 2.0 appears to convert the readings as with all
other rates.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Expose the entire content of the ALG_RESULT_DATA block to the
application, primarily so the status and error flags can be seen. With
those available the application has the ability to detect that a stale
result has been provided so sensor_fetch_sample() can return -EAGAIN in
this case instead of -EIO, and it doesn't need to block which is
annoying.
This should also make the sensor usable on older Nordic Thingy:52
devices with outdated CCS811 application firmware that doesn't properly
implement the DATA_READY bit.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Accurate estimate of gas presence requires temperature and humidity
data. Add API to update these values.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Use CMSIS-standard bit mask and offset macros. Rename the field to more
closely match the data sheet. Use slightly less magic numbers for the
scale multipliers.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Proper use of the CCS811 requires maintenance of the BASELINE
register value measured in clean air at various points in the sensor
life cycle. The sensor driver abstraction has no facility to support
this, so add an application header with functions to fetch and update
the register value.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Add the standard suite of trigger configuration options. Add driver
support for the DATA_READY and THRESHOLD triggers. Note cross-module
dependency as configuring the trigger requires a controlled modification
of the sensor registers and the sensor driver API doesn't support this.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The original implementation relied on the DATA_READY bit of the STATUS
register to indicate when a reading was available. This bit remains
clear for the first several readings produced by the CCS811.
When INT_DATARDY is set in MEAS_MODE the nINT signal will remain
asserted until ALG_RESULT_DATA is read. If this is treated as a LEVEL
signal, which is the common case in Zephyr, gating the read of
ALG_RESULT_DATA on DATA_READY means the signal will never be cleared,
and the interrupt callback will be repeated immediately.
Since the STATUS register value is part of the ALG_RESULT_DATA block
just read the whole thing, and provide its content to the user only if
the DATA_READY bit is set.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 has a measurement lifecycle that includes certain timing
constraints, including that calibration constants should not be applied
until the conditioning period has completed. If a device resets but the
CCS811 remains the process of inspecting current state and initializing
the device properly can be complicated.
Simplify this by forcing a reset of the device when the driver is
initialized. Should this cause hardship the necessary logic and
infrastructure to record time-of-last-reset across reboots and verify
measurement mode/baseline consistency can be added at that point.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Read the status and error in one function that provides its own
diagnostics.
Also change name of register to match datasheet.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The CCS811 can be in either boot mode (after powerup) or application
mode, and these modes have distinct register maps that share only some
content. The register written to switch from boot mode to application
mode is not available in application mode, so don't write to it in that
case.
Also respect the required timeout between APP_START and next I2C
operation.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Allow application to choose the measurement rate.
Measurement mode 4 (250 ms rate) is not supported because it we have no
support for processing the raw data it produces.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Asserting the WAKEn increases current draw. Turn it off when I2C is
not being used.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The amount of lock regions differs between different sam0 MCUs.
saml10: 2
saml11: 4
samd2x: 16
saml2x: 16
samd5x: 32
ASF does not provide a definition for this, so create a new one
in dts.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
This adds support for the flash peripheral found in the SAME5x/SAMD5x
line of MCUs.
The peripheral is very simmilar to the one found on SAMD2x with only
a few register names changed.
Signed-off-by: Benjamin Valentin <benjamin.valentin@ml-pa.com>
Refactors the mcux gpt driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux igpio driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpuart driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Refactors the mcux lpi2c driver to use generated device tree macros
directly. Removes now unused dts fixup macros from i.mx rt and kinetis
socs.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Adds BME280 SPI chip select pin control if chip select is
configured for the device in the device tree.
Signed-off-by: Jan Tore Guggedal <jantore.guggedal@nordicsemi.no>
Need to set device busy when enter into transceive function
in SPI DW driver.
In current SPI DW driver the transceive function don't set busy state,
but that is important for PM busy state.
This will lead to unexpected behaviors when system calls this
function and enter into idle state.
Signed-off-by: Maksim Masalski <maksim.masalski@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Prior to this you would get compilation error when building
samples for the nrf5340_dk_nrf5340_cpuappns board.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
This commit adds SPI driver and its bindings using the USART peripheral
for Silicon Labs EFM32 and EFR32 MCUs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
calling UARTE power management with DEVICE_PM_SUSPEND_STATE
then DEVICE_PM_OFF_STATE causes a deadlock in while loop.
It waits for an event witch never comes
Signed-off-by: Ismael Fillonneau <ismael.fillonneau@stimio.fr>
EEPROM simulator and native_posix have been unified to one solution,
the old eeprom,native_posix is removed.
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Add support for a eeprom simulator. The PR limits the addition to
qemu_x86 but it can easily be added to other devices by defining the
eeprom simulator in the dts and setting 'CONFIG_EEPROM_SIMULATOR=y'
Signed-off-by: Laczen JMS <laczenjms@gmail.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
In STM32 flash driver, don't use semaphore if multithreading
isn't defined.
If multithreading isn't defined, a call to sem_give function
generates a hardware fault exception.
Signed-off-by: Benoit Leforestier <benoit.leforestier@gmail.com>
Add driver for the Texas Instruments LMP90xxx series of multi-channel,
low-power 16-/24-bit sensor analog frontends (AFEs).
The functionality is split into two drivers; an ADC driver and a GPIO
driver.
Tested with LMP90080 and LMP90100.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Before establishing the ppp connection, windows sends the string CLIENT
and expects the reply CLIENTSERVER from the modem.
This functionality is implemented in the new function
ppp_handle_client().
This feature must be enabled via Kconfig.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
Correct handling of device encoded temperature values, which combine a
12-bit 2s complement signed value with a separate sign bit. Rework
conversion between device and sensor temperature representations to
support negative temperatures in both domains.
Use a much simpler trigger configuration where the alert is driven by
comparator output, rather than as an interrupt that requires a pair of
I2C transactions to read and clear the flag.
Refactor the trigger infrastructure to use the setup/handle/process
idiom, which reduces duplicated code and to correctly detect alerts
present when the triggers are set.
Completely replace the sample with something that demonstrates
updating upper and lower threshold values to track moving
temperatures.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Added autocompletion to 'sensor get' command. After this change
device and channels are autocompleted. It is possible to provide
multiple channels for reading.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When asserts were disabled then sensor accepted any channel in
hts221_channel_get(). Changed to return -ENOTSUP when invalid
channel is provided.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
MPU6050 no longer using Kconfig to specify I2C addresses. Reference
to the removed symbol causes QA diagnostics. Remove the reference;
when AK8975 is converted to devicetree it may be possible to restore
the link between the sensors.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a binding for the sensor and replace all Kconfig selection of
hardware parameters with devicetree property values.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
