It was possible to freeze the application by pressing the user button
too frequently. This was likely due to the stack not keeping up with
the send requests and running out of buffers.
Add rate-limiting to the app, so that at most one message per 500ms
can be sent. Also add a user message if the user presses the button
too many times in rapid succession, and inform the other badges of
this misbehaving user.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
There are issues using lowercase min and max macros when compiling a C++
application with a third-party toolchain such as GNU ARM Embedded when
using some STL headers i.e. <chrono>.
This is because there are actual C++ functions called min and max
defined in some of the STL headers and these macros interfere with them.
By changing the macros to UPPERCASE, which is consistent with almost all
other pre-processor macros this naming conflict is avoided.
All files that use these macros have been updated.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
Convert ssd1673 display driver to use new defines so we can remove
the dts_fixup.h code for it. Also dropped "-spi" from compatible.
Fix up references in reel_board dts and sample.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The app is already sending period heart beat messages, and since it is
not designed to be used for such long times that would require IVI
Update, keep the secure network beacon sending disabled.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Suspend the mesh network after 30 minutes of inactivity. This should
help prolong the battery life of boards used at multi-day events, if
the user forgets to power off the device for the night.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
After this fix each LED will blink 5 times. Previously
LED_0 has been blining 6 times while others 5 times.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
If the first name is longer than HELLO_MAX sending would fail due to
there not being sufficient MIC space (or worse overrun the net_buf).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This code was still incorrectly causing corrupt strings to be
generated. Now it should be correct.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Inverse logic for onoff state while driving LED GPIO. For LED light on
GPIO pin is 0, 1 for LED light off.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@codecoup.pl>
The show_sensors_data() function tries to access val[2] when
outputting the Z-axis value, so the array must have at least three
elements. This also triggered Coverity CID 189741.
Fixes#11482
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
This comparison was always supposed to be > rather than >=. Fixing
this also fixes Coverity CID 189740.
Fixes#11483
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Patch introduces sensor model to mesh badge application. Along with
model definition a sensor get message is implemented and handled on
server.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@codecoup.pl>
This patch introduces new screen to mesh_badge application. Sensor
screen shows measurements from board sensors updated every 2 seconds.
Signed-off-by: Grzegorz Kolodziejczyk <grzegorz.kolodziejczyk@codecoup.pl>
Change the label GPIO_KEYS_BUTTON_0_GPIO_CONTROLLER that is generated
for the DT node directly to the corresponding one generated through
the "sw0" alias (i.e. SW0_GPIO_CONTROLLER) to make it consistent with
other DT related labels used in this code (SW0_* and LED?_*).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The way the code is structured the buffer is always guaranteed to be
large enough, however perform explicit termination anyway to avoid
Coverity warnings.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
Add a new "heartbeat" message so that number of hops between nodes can
be discovered. Also add a statistics page which can be toggled using a
long key press, showing local information and the top message senders.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
