net_pkt_tcp_data was only used in tcp unit test and could be replaced by
local net_tcp_get_hdr.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This function is only used in sockets, thus making it a private function
of socket library and renaming it relevantly.
Note that sockets should be reviewed at some point to avoid using such
function: zsock_received_cb() already get the ip header and the protocol
header, so it could grab the src addr/port from there. It would be way
more optimized to do so, since net_pkt_get_src_addr is costly as it
parses all over again the ip/protocol headers.
utils unit test is updated and the test of the former
net_pkt_get_src_addr/net_pkt_get_dst_addr are removed.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The test assumes that the last to IRQ number will be free, this isn't a
valid assumption and now that we detect multiple ISRs registering for
the some IRQ line, we see failures because of this assumption on some
platforms. Exclude those platforms from this test for the time being.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This commit adds specific stm32 CAN driver testing.
The test covers filter handling.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Nios2 platform was disabled due to compilation error. Meanwhile,
issue has been solved and tests can be re-enabled.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The SYS_POWER_LOW_POWER_STATE_SUPPORTED and SYS_POWER_LOW_POWER_STATE
suggests one low power state but these options control multiple
low power state. This commit uses plural in the names to indicate
that.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The following symbols don't exist so remove them from prj_virtual.conf:
CONFIG_I2C_EEPROM_SLAVE_0_CONTROLLER_DEV_NAME
CONFIG_I2C_EEPROM_SLAVE_1_CONTROLLER_DEV_NAME
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
HAS_COVERAGE_SUPPORT can be set both on boards with enough RAM to
store the coverage results, or for POSIX ARCH based ones
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Since this is a test dedicated to Intel S1000 CRB,
use the I2C0 device name directly instead of a Device Tree or
Kconfig defined device name.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
Update DMA tests according to dma_cavs implementation of
single block transfers. Multiple block transfers are achieved
by reloading DMA upon every DMA completion.
Signed-off-by: Sathish Kuttan <sathish.k.kuttan@intel.com>
The code has been using non DT_ prefixed defines for DT generated
defines. Switch to use DT_ prefixed ones as we want to deprecated
the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch adds a JSON web token library that adds the capability
to sign JSON tokens. This was located in subsys due to the dependency
on MBEDTLS, which resides in /ext.
Signed-off-by: David Brown <david.brown@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
Add support to STM LIS2DW12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Co-authored-by: Mario Tesi <mario.tesi@st.com>
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The new spinlock validation features combined with spinlockification
have increased stack usage a bit in CONFIG_ASSERT builds, but this is
a good feature we want to keep. This test was bumping into limits, so
increase the size from 512 to 640 bytes.
Unfortunately, this is also a huge test that creates a LOT of those
stacks across different test cases, so that minor bump blows us past
the 64k SRAM limit on a bunch of boards. So unify all those stacks
that are only ever used in one case at a time so the memory can be
shared. Now there's one fixed stack, named "tstack", and one array
"tstacks". Much smaller.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
These functions, for good design reason, take a locking key to
atomically release along with the context swtich. But there's still a
common pattern in code to do a switch unconditionally by passing
irq_lock() directly. On SMP that's a little hurtful as it spams the
global lock. Provide an _unlocked() variant for
_Swap/_reschedule/_pend_curr for simplicity and efficiency.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Just like with _Swap(), we need two variants of these utilities which
can atomically release a lock and context switch. The naming shifts
(for byte count reasons) to _reschedule/_pend_curr, and both have an
_irqlock variant which takes the traditional locking.
Just refactoring. No logic changes.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
We want a _Swap() variant that can atomically release/restore a
spinlock state in addition to the legacy irqlock. The function as it
was is now named "_Swap_irqlock()", while _Swap() now refers to a
spinlock and takes two arguments. The former will be going away once
existing users (not that many! Swap() is an internal API, and the
long port away from legacy irqlocking is going to be happening mostly
in drivers) are ported to spinlocks.
Obviously on uniprocessor setups, these produce identical code. But
SMP requires that the correct API be used to maintain the global lock.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This test seems to be fine in the current master, but doing
development, it easily starts to overflow RAM of some boards and/or
crash due to stack checks. So, decrease the ramdisk (the biggest
eater of RAM here) from default 96K to 80K, and bump main stack
size proactively.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Implemented tests for the new join and detach features.
- The first tests multiple join operations.
- The second tests trying to join a detached thread.
- The third tests abandoning a join when the thread is detached after
creation.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
This implements the Database Hash characteristic which generates a hash
with the contents of certain attributes. The generation of hash is
usually offloaded to the systemwq using a delayed work so that when
application register multiple services only one hash needs to be
calculated.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Patch introduces flash_map subsystem to operate on flash
image instead of direct operation using flash_driver API.
Changes allows to support operation on the image in any flash
device.
flash_map was not available when this subsystem was introduced.
Signed-off-by: Findlay Feng <i@fengch.me>
Patch introduces flash_map subsystem to operate on flash
footprint instead of direct operation using flash_driver API.
Flash area ID is used in API instead of direct flash-bank-offsets.
Changes allows to support operation on the partition in any flash
device.
flash_map was not available when this subsystem was introduced.
Signed-off-by: Findlay Feng <i@fengch.me>
The power management framework used two different abstractions
to describe power states. The SYS_PM_* given coarse information
what kind of power state (low power or deep sleep) was used,
while the SYS_POWER_STATE_* abstraction provided information
about particular power mode.
This commit removes the SYS_PM_* abstraction as the same
information is already carried in SYS_POWER_STATE_*.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
Default to the PWM0 channel 2, as it is the only one available in a
non-inverted form on the EXT1 and EXT2 connectors. That way the measured
voltages match the expected ones.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The DAD was failing because we received the DAD network packet
even when should not had received it. Fix it by discarding all
the ICMPv6 NS packets that we receive.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The packet can be referenced somewhere else and letting the newly added
L2 header will generate corrupt packet. If the same packet is being
resent, ethernet will add again its L2 header. Thus the need to remove
such L2 header every time a packet has been sent, successfully or not.
Fixes#12560
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This was never a long-term solution, more of a gross hack
to get test cases working until we could figure out a good
end-to-end solution for memory domains that generated
appropriate linker sections. Now that we have this with
the app shared memory feature, and have converted all tests
to remove it, delete this feature.
To date all userspace APIs have been tagged as 'experimental'
which sidesteps deprecation policies.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
CONFIG_APPLICATION_MEMORY was a stopgap feature that is
being removed from the kernel. Convert tests and samples
to use the application shared memory feature instead,
in most cases using the domain set up by ztest.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
* Newlib now defines a special z_newlib_partition containing
all globals relevant to newlib. Most of these are in libc.a
with a heap tracking variable in newlib's hooks.
* Both C libraries now expose a k_mem_partition containing the
bounds of the malloc heap arena. Threads that want to use
libc malloc() will need to add this to their memory domain.
* z_newlib_get_heap_bounds has been removed, in favor of the
memory partition for the heap arena
* ztest now includes the C library partitions in its memory
domain.
* The mem_alloc test now runs in user mode to prove that this
all works for both C libraries.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
If CONFIG_APP_SHARED_MEM is enabled, ztest will set up a
default memory domain with a single partition on startup.
Test case globals may be added to the partition via
ZTEST_BMEM/ZTEST_DMEM macros, add their own partitions,
or leave the domain and join another one.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Some tests instantiate a lot of thread objects. These
were not tagged with __kernel, and
CONFIG_APPLICATION_MEMORY was enabled, so the kernel was
not adding them to the kernel object database.
However, with CONFIG_APPLICATION_MEMORY disabled, this
overflowed the default max number of thread objects (16).
Increase the max to 32 for these particular tests.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
We want CONFIG_APPLICATION_MEMORY specifically disabled
for this test, but it was being transitively selected by
CONFIG_TEST_USERSPACE which defaults to on for CONFIG_TEST.
Turn it off so that disabling application memory in the
config actually has an effect.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Fixed typo: CONFIG_NET_NET_PKT_LOG_LEVEL_DBG, removed extra _NET.
Removed debug macro CONFIG_NET_DEBUG_NET_PKT that is not used.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The function to set channel alarm is called counter_set_channel_alarm.
To match the name of the function performing the reverse operation this
commit renames counter_disable_channel_alarm() function to
counter_cancel_channel_alarm().
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Interrupts default to trigger on level for historical reasons, so use of
GPIO_INT_LEVEL` as a mask results in a zero value. Use a mask macro to
isolate the trigger configuration.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Update counter_basic_api test to support STM32 RTC counter.
Add device to list and skipp not supported test cases.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enable testing of counter (COUNTER_{D}TMR_CMSDK) on mps2_an385 and
enable timers on v2m_beetle (TIMER_{D}TMR_CMSDK).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Enables debug logging in the counter_basic_api test. Fixes a build error
in the nrf counter drivers when logging is enabled.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
The mcux rtc hardware supports a single alarm only and a fixed top
value, so restructure the counter_basic_api test to skip unsupported
features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Tests i.MX EPIT timer peripheral driver. Since it supports zero number
of channel alarms, some tests had to be adjusted to look at the
number of channel alarms supported first.
Signed-off-by: Stanislav Poboril <stanislav.poboril@nxp.com>
Renamed:
- counter_set_wrap to counter_set_top_value
- counter_get_wrap to counter_get_top_value
- counter_get_max_wrap to counter_get_max_top_value
Updated nRF implementations and counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Modify alarm callback to return user_data and channel_id.
Set_alarm and disable_alarm updated accordingly. Renamed
counter_*_ch_alarm to counter_*_channel_alarm. Updated test
and nrf implementations.
Updated doxygen comments.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Using `COUNTER_2_NAME` when all other properties are
`COUNTER_TIMER2_foo` is confusing. Make the names consistent.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
RTC1 (not RTC0) is excluded because it is used as the system clock.
Also document that TIMER0 and RTC0 may be rejected when CONFIG_BT_LL_SW
is enabled.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
The test assumes that the last to IRQ numbers will be free, this isn't a
valid assumption and now that we detect multiple ISRs registering for
the some IRQ line, we see failures because of this assumption on some
platforms. Exclude those platforms from this test for the time being.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Set Kconfig symbol SETTINGS_FCB_FLASH_AREA based on the
DT_FLASH_AREA_<FOO>_ID define instead of being hard coded.
We replace 3 with DT_FLASH_AREA_IMAGE_SCRATCH_ID and
we replace 4 with DT_FLASH_AREA_STORAGE_ID.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
After addition of flash_map auto-generation it is needed to
use generated flas_area name instead of hard-code.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The test had hard coded address family with value 4. This test
was failing as we have now AF_CAN family with value 4. Use 99
as an invalid address family value instead.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As we are adding more protocol families and protocol types
to connection handlers, some values might be same across
different types. Current connection handler only stores
proto type to match the handler, which is not enough if
we add more types. Also combination of family and types
may vary too. So adding family to connection handler to
figure out best match.
Also changing proto variable in net_conn from u8_t to u16_t.
net_context has 16 bit proto.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
After including native_posix USB controller we can perform some simple
tests on native_posix.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Added a set of tests that use the default thread stacks to ensure they
work the same as the passed in stacks. Abstracted the common
functionality into functions.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
Implemented a second set of memory pool tests that function on a
dynamically allocated memory pool. Abstracted some of the common
functionality to a common function.
Signed-off-by: Carlos Stuart <carlosstuart1970@gmail.com>
PAE tables introduce the NX bit which is very desirable
from a security perspetive, back in 1995.
PAE tables are larger, but we are not targeting x86 memory
protection for RAM constrained devices.
Remove the old style 32-bit tables to make the x86 port
easier to maintain.
Renamed some verbosely named data structures, and fixed
incorrect number of entries for the page directory
pointer table.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Those are outdated and unrunnable tests that require lots of
customization to keep them building and the information they provide
can't be retrieved in other means.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The iterator over registered callbacks failed to account for the
possibility that the callback would remove itself from the list. If
this occurred any remaining callbacks would no longer be reachable from
the node. Switch to the slist iterator that is safe for self-removal.
Note that the slist API remains unsafe for removal of subsequent nodes.
Even with the corrected code removal of the next callback registration
(cached in tmp) will result in it being called anyway, with the
remaining unremoved registrations not being called. If the next
callback were removed and re-registered on a different device, the
callbacks would be invoked for the wrong device.
Resolve this by a documentation change describing the conditions under
which a change to callback registration from within a callback are
permitted. Add a similar note regarding the effect of adding a
callback. The current event invocation behavior for callbacks added
within an event is explicitly left unspecified, though in the current
slist implementation newly added callbacks will not be invoked until the
next event.
Closes#10186
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
As the legacy library has been removed, we no longer need to
differentiate betwen MQTT implementations. Therefore align the library
folder name with other libraries and remove the `_sock` suffix.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Include the HCI Mesh Extension implementation to be built in
CI. Note, mesh extension implementation is work in progress,
and will be continues in new LL split architecture
implementations.
Note, HCI Mesh extensions not supported in ULL/LLL arch yet,
hence disabled. Also, only a partial implementation present
in the old architecture.
Relates to #12860.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Include building the init tests with the new Link Layer
split architecture and with debug options to cover
possible conditional compilations.
Relates to #12860.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
This commit moves the definition of IRQ_LINE(..) macro from
interrupt.h into nested_irq.c, and adds some inline comments
documenting the use of it.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
As we are removing net_app and net_pkt based libraries and
applications, CoAP legacy based libraries and apps are moved
to socket based implementations. So removing legacy CoAP.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
As written originally, the tests assumed that if k_uptime_get_32()
returns times in milliseconds, that it also has millisecond
resolution. That however doesn't have to be the case, and indeed,
default timer interrupt period used by Zephyr is 10ms, and so system
time is incremented in such units. So, instead of "<= 1" tests to
account for timing increment, use "<= FUZZ".
For blocking tests, increase the timeout from previously used 10ms,
so we can reliably tests delays under the conditions described.
Also, enable CONFIG_QEMU_TICKLESS_WORKAROUND. Most other
timing-related tests have this enabled, and it may affect
stability of QEMU testing too.
Fixes: #12994
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This commit adds support for device id shell command.
Example:
uart:~$ hwinfo devid
Length: 12
ID: 0x1b0320d51485330313420
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
In case of Ethernet, if the requested size is larger than MTU and if
AF_UNSPEC is provided, the allocator will need to take into account
the ethernet header size which is not accounted in the MTU.
Other current L2 do not follow that rule as their MTU is based on IP
one (IPv6 most of the time). What they declare as MTU is the full frame
size they handle (minus the FCS for instance in 15.4). So with
AF_UNSPEC, such assumption on L2 header size is unrelevant.
(On 15.4 the header size is variable anyway and cannot be known until
the frame is parsed).
Fixes#12982
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Very simple test for thread CPU masks. While this is a SMP feature,
the implementation doesn't actually depend on SMP so we can test it
right here in the thread_apis test.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
STM32 watchdog driver does not support callback which is not expected
by the test. Update to make test able to run on STM32 drivers.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This allows to place instances of the class one after another in the
linker section.
Fixes#12908
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
USB relies on descriptors and configuration data allocations in
specific sections. This simple test verifies that at least size of the
data is correct.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The sys_dlist_insert_*() functions had a behavior where a NULL
argument for the insertion position to sys_dlist_insert_after/before()
was interpreted as "the end of the list". We never used that
convention (except in one spot internal to dlist.h which was not
itself used anywhere), and of course already have an API for appending
and prepending to a list.
In practice this was a performance disaster. The NULL check is
virtually never provable statically by the compiler, so that test and
branch is present always. And worse, the check and call to another
function was pushing this beyond the complexity limit for gcc to
inline a function (at -Os optimization anyway), forcing us to use
function calls for what should be a ~8 instruction sequence. The
upshot is that dlist insertions were 2-3x slower than they needed to
be.
Deprecate these older APIs and introduce a new sys_dlist_insert() call
which can be much better optimized.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Useful tool for performance work that removes interaction with other
APIs and thread state. The best part is that it doesn't rely on timer
interrupt delivery and so works with -icount even on existing qemu
versions and produces deterministic output.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
If status is 0, both ip_hdr and proto_hdr will own a pointer to the
relevant IP and Protocol headers. In order to know which of ipv4/ipv6
and udp/tcp one will need to use respectively net_pkt_family(pkt) and
net_context_get_ip_proto(context).
Having access to those headers directly, many callbacks will not need
to parse the packet again no get the src/dst addresses or the src/dst
ports. This will be change after this commit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Though these are currently used by the core only, it will be then used
by net_context as well. This one of the steps to get rid of net_pkt's
appdata/appdatalen attributes.
Also normalizing all ip/proto parameters name to ip_hdr and proto_hdr.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This goes through basic allocation, atomic read/write, data
getter/setter and cloning/copying.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The test counts the '\0' of the data copied, though it does not belong
to the packet.
Since the test by-passes net_ipv6_input, which would update the packet
length according to what is in the IPv6 header, the checksum calculation
fails.
Before, checksum calculation used to grab the length from IPv6 header,
but that changed to use net_pkt_get_len(): that one must provide the
real lenth.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Only next to be removed functions like net_tcp_set_checksum() are left
untouched. All the rest is switched.
Adding net_tcp_finalize() to follow the same logic as for UDP and else.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This proovse to drastically reduce runtime overhead as it does not need
to parse IP nor TCP header all over again in a lot of places.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
As these were parsed already by IPv4/6 input functions let's use them.
Applying the change on trivial UDP usage. TCP usage will have its own
commit.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This optimizes the memory quite a bit since we do not need to clone nor
split the original packet at any time.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Most of the code had to be reworked due to the new API: it's more
logical to do everything sequentially (first headers, then MLD part)
than the contrary with inserting headers at the end.
Using get_data/set_data as well it makes the code clearer.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Reworking the logic to reduce the amount of variables.
This part was heavier to change as it was not accessing the headers
directly but instead was read parts by parts.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
In nbr part, this is a useful information. Since net_icmpv6_input has
already parsed the icmpv6 header, let's get pass it, instead of
retrieving/parsing it again in various handler functions.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is meant to remove the need for macro NET_IPV6_HDR(), since we
don't know in future if accessing the header that way will be valid.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Use the new net_pkt API to proceed through IPv6 header and all the
extension header as well.
Use udp/tcp input functions relevantly, and call net_conn_input
afterwards.
Note: This commit temporarly disable IPv6 fragmentation support
in the code directly. Which support will be re-enabled afterwards.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
checksum_offload is now the only one using that function, let's get rid
of such usage.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The net-app API is removed. Users should use the BSD socket API
for application development.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use auto-generated device tree macros in LPS25HB driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DS0 driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
This board is unmaintained and unsupported. It is not known to work and
has lots of conditional code across the tree that makes code
unmaintainable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The disabled test causes crash in qemu_x86, so temporarily disable
it until a proper fix is found.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit makes the necessary changes to allow the following tests
to run on cc3220sf_launchxl:
- mqtt_packet
- mqtt_publisher
- mqtt_subscriber
- mqtt_pubsub
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
There was a false timeout error because we did not check the
return value correctly. This issue is seen now because code
flow in core IP stack is happening in different order than
before.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There are no longer per-partition initialization functions.
Instead, we iterate over all of them at boot to set up the
derived k_mem_partitions properly.
Some ARC-specific hacks that should never have been applied
have been removed from the userspace test.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The public APIs for application shared memory are now
properly documented and conform to zephyr naming
conventions.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Building of nsim_em board will get the NSIM UART build tested so no need
to have an explicit test for it here.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Minor change:
Rename the file names of the test scripts for consistency with
other BLE code
The simulation identification string is also changed (although
there is no actual functional need)
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
To also cover the new split controller architecture (with a common ULL
and vendor dependent LLL).
Add a connection testcase (without encryption so far) for the nrf52_bsim
configured with the split controller architecture.
This is just the exact same as the Basic_con test but building the test
with CONFIG_BT_LL_SW_SPLIT=y.
Privacy and data lenght extensions are also so far disabled as the
new controller does not yet support them.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
To allow for incremental builds also when 2 projects are only
differentiated by the project configuration file.
Separate the build dirertories also by the selected project file.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
It is the macro name that matters, not its value. Here, that will help
to save 1 bit in struct net_pkt later on.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The app shared memory macros for declaring domains provide
no value, despite the stated intentions.
Just declare memory domains using the standard APIs for it.
To support this, symbols declared for app shared memory
partitions now are struct k_mem_partition, which can be
passed to the k_mem_domain APIs as normal, instead of the
app_region structs which are of no interest to the end
user.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add test to log_output module. Test suite covers usage of
log_output_string function.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Changed 'in place' mode to bypass logger system and directly
call active backends. With this approach memory footprint of
the logger can be significantly reduced in terms of RAM and ROM.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
The previous commit replaced the net_pkt element ref with an element
atomic_ref. CI tests turned up more places where ref was used directly.
This commit converts them to use the new element.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Use auto-generated device tree macros in LIS3MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2MDL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LSM6DSL driver to avoid
usage of dts.fixup code for it.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Updated the GCOV_COUNTERS value, without which the coverage data
was corrupted when gcc 8.2 was used.
GH-12571
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Several places in the code have constructions like this:
if (bool_variable) {
atomic_set_bit(flags, FLAG);
} else {
atomic_clear_bit(flags, FLAG);
}
To reduce the amount of code for such situations, introduce a new
atomic_set_bit_to() helper which lets you condense the above five
lines to a single one:
atomic_set_bit_to(flags, FLAG, bool_variable);
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The old legacy APIs use net-app library and as that is being
removed, then the dependencies need to be removed also.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Include building the init tests with the new Link Layer
split architecture.
Has the data length update and controller privacy disabled
until they are implemented in the new architecture.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Basic test for poll() behavior. UDP sockets are used for simplicity
so far (poll-related paths for UDP and TCP are similar, though later
adding TCP explicitly for full coverage may be useful).
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The idea is that we should have many, many tests. The only reasonable
way to achieve that is by making tests easy and pleasant to write,
and that requires common, easy to reuse infrastructure.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
1. Consistently use prepare_sock helpers.
2. Test not just client->server sending, but sending reply.
3. Send large packets (>1 net_buf fragment), not just small.
4. Check POSIX behavior on recv()ing datagram incompletely (the rest
should be discarded and next recv() should read next datagram.
5. More cleanroom testing, e.g. explicitly reinitialize input params
on each call (without assumptions that they're left with suitable
values from previous calls), clear input buffers before each read
operations, etc.
6. Reformat code. Previously it was very sparse, giving long test
functions, and thus impression that tests are complicated and hard
to write.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Share lis2dh driver among few accelerometer sensors that has
same register interface: LIS2DH, LIS3DH, LSM303DLHC, LIS2DH12,
LSM303AGR.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Use auto-generated device tree macros in LIS2DH driver to avoid
usage of dts.fixup files. The triggered interrupt part has been
slightly hacked to automatically understand whether only int1 is
configured or both int1 and int2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
The original implementation allows a list to be corrupted by list
operations on the removed node. Existing code attempts to avoid this by
using external state to determine whether a node is in a list, but this
is fragile and fails when the state that holds the flag value is changed
after the node is removed, e.g. in preparation for re-using the node.
Follow Linux in invalidating the link pointers in a removed node. Add
API so that detection of particpation in a list is available at the node
abstraction.
This solution relies on the following steady-state invariants:
* A node (as opposed to a list) will never be adjacent to itself in a
list;
* The next and prev pointers of a node are always either both null or
both non-null.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Added tests for async UART API and test configuration for
nrf52840_pca10056 board.
For tests to work, RX and TX pins have to be connected together
and second UART is needed to output results to console.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Add support to STM LIS2DS12 3-axis accelerometer driver.
The driver support I2C and SPI bus communication and both
polling and drdy trigger mode.
Currently it uses high resolution only as power mode.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
lib/ was starting to get messy and inconsitent. Files being either
dumped in the root or in sub-directories without a clear plan.
Move all library components into one single folder and call it 'os'.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Minor adjustments are done to the nRF clock_control and rtc_timer
drivers to make them usable on nRF9160 as well.
The arm_irq_vector_table test code is modified only because it uses
the function that has been renamed in the nrf_rtc_timer driver.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
There is an effort underway to make most of the Zephyr build script's
reentrant. Meaning, the build scripts can be executed multiple times
during the same CMake invocation.
Reentrancy enables several use-cases, the motivating one is the
ability to build several Zephyr executables, or images, for instance a
bootloader and an application.
For build scripts to be reentrant they cannot be directly referencing
global variables, like target names, but must instead reference
variables, which can vary from entry to entry.
Therefore, in this patch, we replace global targets with variables.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Prolong by 1 second the BT encrypted connection test, to ensure
there is enough time for the link itself to be encrypted.
Before this change the key was exchanged, but the 1st notification
(pass condition) was received before the link itself was encrypted.
With this change we wait for 1 notification more (1 second more),
and during that extra second the link is actually encrypted.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
printk is supposed to be very lean, but should at least not
print garbage values. Now when a 64-bit integral value is
passed in to be printed, 'ERR' will be reported if it doesn't
fit in 32-bits instead of truncating it.
The printk documentation was slightly out of date, this has been
updated.
Fixes: #7179
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a configuration structure to sht3xd that holds instance-specific
parameters, implemented in a immutable statically allocated object
initialized with material from device tree binding aliases.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
Fails sporadically on this platform and causing CI blockage.
Filed bug #12478. Should be reverted once bug is fixed.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
We have a new power management system and those samples have been
written for specific boards and using the application based power
management subsystem. We are getting new tests/samples that are generic
with the new subsystem, so remove those in favor of the new ones.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This commit adds a test case checking if ADC drivers can work properly
after discarding an invalid sampling request.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Apart from normal customizations of vendor specific parameters in ADC
configuration used in the test, a few more changes in test cases were
also introduced in commit 1bfa34f4fb.
This resulted in some parts of ADC API (like zero interval between
consecutive samplings) not being tested at all. This commit restores
the original behavior of the test cases (with added comments that
zero intervals are intentional).
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Currently only nRF drivers need assignments of analog inputs to ADC
channels (ADC_CONFIGURABLE_INPUTS Kconfig option is activated only for
these drivers). Hence, there is no need to define ADC_xxx_CHANNEL_INPUT
labels for any other ADC driver as they will be ignored anyway.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
These were being truncated to 32-bits, and only 8
hex digits were supported.
An extraneous printk() at the beginning of the test
which was not being tested in any way has been removed.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Change driver to get I2C address of sensor from the device tree like
most other sensor drivers that utilize device tree.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert lsm303dlhc_accel & lsm303dlhc_magn sensor driver to use new
defines so we can remove the dts_fixup.h code for it.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Use DT_ instead of CONFIG_ for spi freq, spi bus name, flash device
name and flash base address.
Signed-off-by: Rajavardhan Gundi <rajavardhan.gundi@intel.com>
Disabled the CONFIG_COVERAGE for benchmarks and other tests.
This is needed because it interferes with normal behavior of the
test case.
Signed-off-by: Adithya Baglody <adithya.nagaraj.baglody@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
