Using find_package to locate Zephyr.
Old behavior was to use $ENV{ZEPHYR_BASE} for inclusion of boiler plate
code.
Whenever an automatic run of CMake happend by the build system / IDE
then it was required that ZEPHYR_BASE was defined.
Using ZEPHYR_BASE only to locate the Zephyr package allows CMake to
cache the base variable and thus allowing subsequent invocation even
if ZEPHYR_BASE is not set in the environment.
It also removes the risk of strange build results if a user switchs
between different Zephyr based project folders and forgetting to reset
ZEPHYR_BASE before running ninja / make.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
The nRF52840 DK board target, so far known as nrf52840_pca10056,
is renamed to nrf52840dk_nrf52840.
Its documentation and all references to its name in the tree are
updated accordingly. Overlay and configuration files specific to
this board are also renamed, to match the new board name.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add information about how to build and test atsamr21_xpro board with
IEEE 802.15.4 RF2xx driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add special configuration for SAMR21 SoC. Since it have only 32k SRAM,
all possible application buffers need to be shrinked. This
configuration was tested with two boards for more than 2H with success.
[02:18:57.635,00] net_echo_server_sample: IPv6 UDP: Sent 333000 packets
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
UDP portion of the echo_client sends 1 packet with the sample data.
(TCP can send chunks of it depending on the response of the send()
function.) Not every network interface can send a UDP packet large
enough to handle the size of the sample data.
Let's make sure to account for the network interface MTU when deciding
the amount of sample data to send.
Fixes: https://github.com/zephyrproject-rtos/zephyr/issues/22447
Signed-off-by: Michael Scott <mike@foundries.io>
Add Kconfig option NET_SAMPLE_SEND_ITERATIONS that sets the number of
times the Zephyr echo client sample sends its data. By default the
value is zero, which means indefinite, and demonstrates the same
behavior as before.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
This count is assigned to CONFIG_BT_ACL_RX_COUNT which expects a number
in the range of 1-64, otherwise kconfig fails.
Fixes#22259
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Fixed bug in udp.c in echo_client and echo_server samples.
The bug causes UDP sockets to not close if socket id is 0.
Signed-off-by: Magne Værnes <magne.varnes@nordicsemi.no>
OpenThread settings implementation built on top of Zepyhr settings
submodule.
With this solution, OpenThread settings are identified with keys of
the following format: `ot/id/instance`, where `id` is assigned by
OpenThread stack, and `instance` is a 32-bit random number, both in
hex. The implementation makes use of `settings_load_subtree_direct`
function to iterate over settings instances. This allows the
OpenThread settings layer to be a fully transparent shim layer between
OpenThread/Zephyr APIs.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
echo_client and echo_server configuration for 802.15.4 and OpenThread is
covered by overlay files and default board configuration. Board-specific
configuration for frdm_kw41z was redundant in this case.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
PSK support is added to echo-client.c and echo-server.c.
If enabled, a header is included which contains the PSK.
If the default dummy PSK header is used, a warning is issued.
The header can be changed via Kconfig.
Signed-off-by: Torstein Grindvik <torstein.grindvik@nordicsemi.no>
Add some mbedTLS tweaks for OpenThread in overlay-ot.conf.
Add sample configuration to enable Commissioner/Joiner, disabled by
default.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
While trying out the hello_world sample built for QEMU, I was expecting
the sample app to exit and I'd return to a command prompt. Nope. You
need to exit QEMU manually, so add that step to the sample instructions.
Looking around, there are more uses of QEMU like this that could use
this added step after running the sample app.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
SOCKS5 support added to echo_client. Details are added
in README file about how to verify this feature using
echo-client with echo-server running on Linux host.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
This commit adds a sample configuration for 6LoCAN to the
echo_client and echo_server example.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The `start_udp_and_tcp` funcion is a blocking function, therefore it
should not be called from the system workqueue, as it would stall it.
Because it was called in such a way, the retry mechanism, which
also relied on the system workqueue did not work properly.
This commit fixes the issue, by keeping the main application processing
in the main thread, and using a semaphore to synchronize with the
connection manager.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Remove old configurations of boards that do not support networking
natively and very custom and difficult to test.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Start to monitor Connected and Disconnect events and then start
and stop the echo service according to system connectivity status.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Converts all net samples that enable the mcr20a 802.15.4 driver to use
the frdm_cr20a shield instead of hardcoding configs for the frdm_k64f
base board. This makes it possible to build mcr20a samples for other
base boards with compatible arduino headers.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Clean up some stray references to cmake in doc, boards and
samples that don't make explicit use of the zephyr app extension,
as well as other minor doc fixes.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
The DT spec. only has "okay" and not "ok". The Linux kernel has around
12k "okay"s and 300 "ok"s.
The scripts/dts scripts only check for "disabled", so should be safe re.
those at least.
The replacement was done with
git ls-files | xargs sed -i 's/status\s*=\s*"ok"/status = "okay"/'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
`CONFIG_NET_L2_BT` no longer forces required BT configuration, but
depends on a user to set a valid configuration instead. Hence, we
need to select a proper configuration in the overlay config file.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
This patch adds the overlay when the echo-server is running on Linux and
echo-client is running on Qemu.
Fix: #14654
Signed-off-by: Tedd Ho-Jeong An <tedd.an@intel.com>
A new role :zephyr_file: is available that renders to a link to the file
or folder in GitHub. Find appropriate references using :file: and
convert to :zephyr_file: to take advantage of its linking capability.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
CONFIG_IEEE802154_CC2520_AUTO_ACK seems to creep back in, but has long
since be removed. We remove old references a few times.
Commit 2facf33f28 - "net: ieee802154: Remove old cc2520 AUTO_ACK
assignments".
Remove them again.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Port all users of 'set_conf_file' to use the built-in rules
instead. This follows the convention-over-configuration principle to
make the system as a whole simpler and more consistent.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
Added more detailed information how to connect Zephyr instance
to host system like Linux desktop.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net-app based echo-server/client applications were used for
various smoke testing purposes. As those two apps are now removed
we need to introduce the same support into sockets based echo-client
and echo-server applications.
Fixes#13300#13481
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
As the net-app based echo samples are being removed, there's no use
referencing them any longer in their socket counterparts.
Additionally, overlay configuration descriptions were added in the
same manner original samples did.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
These were still running through Ethernet using generic
overlay-802154.conf thus creating a dedicated one.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Move to latest cmake version with many bug fixes and enhancements.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Increase rx stack size for OpenThread overlay, as updated revision of
OpenThread requires more stack to operate.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Current application data size in echo_client sample does not fit into a
single datagram with DTLS enbled for default IPv6 MTU (1280 bytes). This
caused abrupt failure of the sample with DTLS enabled over 802.15.4 L2.
Decreasing the application data size allows it to fit into a single UDP
datagram after encapsulating it into DTLS record.
Additionally, finetune DTLS timeout on echo_server to match UDP
application timeout on echo_client (so that a single datagram loss
does not cauase DTLS session to end).
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
Use generic logging macros LOG_*() instead of NET_*() as the
latter are mostly meant for internal networking stack use.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Remove network specific default and max log level setting
and start to use the zephyr logging values for those.
Remove LOG_MODULE_REGISTER() from net_core.h and place the
calls into .c files. This is done in order to avoid weird
compiler errors in some cases and to make the code look similar
as other subsystems.
Fixes#11343Fixes#11659
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add Bluetooth, 802.15.4 and OpenThread overlay configurations to socket
echo_client and echo_server samples.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to prevent failing tests on i.MX RT the following samples were
limited to a minimum 140k of flash: http_client, http_server,
socket/echo_client and sockets/echo_server.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
When using an IDE (e.g. Eclipse, Qt Creator), the project name gets
displayed. This greatly simplifies the navigation between projects when
having many of them open at the same time. Naming every project "NONE"
defeats this functionality.
This patch tries to use sensible project names while not duplicating
too much of what is already represented in the path. This is done by
using the name of the directory the relevant CMakeLists.txt file is
stored in. To ensure unique project names in the samples (and again, in
the tests folder) folder, small manual adjustments have been done.
Signed-off-by: Reto Schneider <code@reto-schneider.ch>
