I don't have much explanation for this change except that
I can't program soc on these boards with this option being set.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Similar to what was done for other h7 based boards,
use 'connect_assert_srst' and fix init routine.
Fixes#29732
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Resource sharing between m7 and m4 core was a bit abusive
as the whole SERIAL ports where disabled on m4 core.
Since it is possible to use a finer grain resource sharing and
having no serial node configured could lead to compilation issue
in some samples assign usart8 to m4 target.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
On these 3 stm32h7 based boards, 'connect_assert_srst' should
be used in order to be able to program after board unplug/plug.
Problem is that 'connect_assert_srst' prevents gdb-attach procedure
to complete which now requires 'reset halt' to be performed before
hand.
Fix this by forcing 'reset halt' by introducing a new init routine.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since this board is fully supported on openocd,
let's use openocd to comply with other boards and
remove the dependency on stm32cubeprogrammer.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Some pins on the arduino header and on the mikrobus header were wrong.
These are now corrected. They are the same on the lpcxpresso55s28
board.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
On stm32mp157c_dk2, the pin mapped on arduino connector pin A3
could not be used as GPIO.
As a consequence, pin "irq-gpio" from x_nucleo_iks01a3 shield
should not be used.
Use board overlay to remove it from shield definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
According to boards schematics, user button is pulled down by
external resistor when not pressed and pushing the button sets
it to high.
Fixes#30224
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add a note in the documentation regarding the required
nRF Command Line Tools for properly working with the
nRF5340 DK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The current SAM4S define at board level common flags that should be on
soc defines. Add common flags at SoC Kconfig defines and drop the
correspondent at board defines.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The current SAM4E define at board level common flags that should be on
soc defines. Add common flags at SoC Kconfig defines and drop the
correspondent at board defines.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The bug on TFM that prevented to enable MPU on NS side is
fixed on TFM current version.
MPU can now be safely enabled on NS target.
Fixes: #27809
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Discussion while adding the blackpill_f401ce board definition brought
up a few issues with the blackpill_f411ce board definition, which are
addressed in this commit:
* doc/index.rst had a typo
* support/openocd.cfg was incorrectly using the f4discovery profile,
which was fixed by using a custom profile for the SoC instead
* removed SoC from blackpill_f411ce.dts compatible line
* added support for jlink flash option
Signed-off-by: Kalyan Sriram <coder.kalyan@gmail.com>
Duplicates the existing blackpill_f411ce board definition for the
blackpill_f401ce board (WeAct Blackpill V3.0), which has identical specs
except for 84MHz clock (instead of 100Mhz) and 96K SRAM (instead of
128K).
Signed-off-by: Kalyan Sriram <coder.kalyan@gmail.com>
Update nrf21540 DTS to support FEM configuration and update other pins
according to te board datasheet
Signed-off-by: Jakub Pegza <Jakub.Pegza@nordicsemi.no>
The gpio port of D4 on the arduino header was incorrect and is now
corrected to PF_14.
Signed-off-by: Christian Taedcke <christian.taedcke@lemonbeat.com>
I have experienced some problems when flashing this board using OpenOCD.
Adding `connect_assert_srst` forces reset assertion before any
connection atempt (`srst_nogate` is required).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add i2c1 interface for stm32l552xx and stm32l562xx microcontrollers
and enable i2c1 that connects to lsm6dso sensor module on the
stm32l562e_dk board.
Signed-off-by: Yestin Sun <sunyi0804@gmail.com>
Fix typos, inconsistent naming and formatting issues.
Also setting CONFIG_NFCT_PINS_AS_GPIOS=y because NFC is not used.
Signed-off-by: Martin Jäger <martin@libre.solar>
Add Kconfig options that will be used by the module
to call the function with the desired parameters.
Refactor the tfm_integration samples and
the supported boards.
Update west.yml to bring in Cmake changes that use the new KConfigs.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
GR716A microcontroller evaluation board with features an 80-pin
mezzanine connector. Also supports simulating with TSIM3.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This board configuration is compatible with
- GRLIB GPL FPGA template designs
- TSIM3 LEON3 eval
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
This board configuration can be used out-of-the-box with SPARC QEMU
distributed with Zephyr SDK v0.11.2.
Signed-off-by: Martin Åberg <martin.aberg@gaisler.com>
Support for the NUCLEO-L031K6 development board with STM32L031K6 SoC.
Although the SoC only contains 32k flash and 8K RAM, it has been tested
on a number of samples and has worked as expected.
Signed-off-by: Steven Daglish <s.c.daglish@gmail.com>
Fixes: #28462
This commit allows shields to be defined in other BOARD_ROOTs, either
using `-DBOARD_ROOT=<path>` or a Zephyr module defined BOARD_ROOT.
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This is done to facilitate multi image build systems
where child images could be associated with a different
core than the parent image.
In such situations, the name of the board associated with
the core of the child image must be known.
Boards for the 'CPUNET' domain is already in place.
This commit adds the boards for the 'CPUAPP' domain.
These would be needed if the parent image is build in the
'CPUNET' domain, and the child image is in the 'CPUAPP'
domain.
Signed-off-by: Håkon Øye Amundsen <haakon.amundsen@nordicsemi.no>
For the application core, the `--device` parameter specifies only
the generic `cortex-m33`, so it is impossible for the debugger to
flash the target.
For the network core, the `--device` parameter is not present at all,
so it is even impossible to run the `debug` command.
This commit fixes the above issues by specifying the proper devices.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update nsim board documentation:
* add info about run on HW (HAPS)
* update info about dependencies in case of single / multi core
runs in simulation and run on HW
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
ARC nSIM boards (starting with nsim_ prefix) allow to run
Zephyr in simulator and on real hardware.
Allow to run Zephyr on HW by enabling mdb-hw runner.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
mdb runner is quite special as it can be used to run Zephyr on
both simulator (nSIM) and real hardware.
However it is really misleading as same command (west flash)
will run Zephyr in simulation for one board and try to run it
on HW for another board. Things are getting worse for boards
supporting both runs in simulation and on real hardware.
Let's split mdb runner for mdb-hw (for runs on HW) and mdb-nsim
(for runs in simulation) runners.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Move i2c to defconfig
Add documentation
Improve dts
Remove unnecessary option and only use the default ones.
Provide a default Active state directly in the device tree
Fix copyright
Signed-off-by: Stephane Dorre <stephane.dorre@gmail.com>
Disable setting CONFIG_SOC_FAMILY_NRF manually
Limit SPI frequency to 8MHz
configure new st7789v in device tree
Signed-off-by: Sergey Koziakov <dya.eshshmai@gmail.com>
Basic sample program that uses the one led and button from the Pinetime.
Led will turn on everytime the button is pushed.
Signed-off-by: Rafa Couto <caligari@treboada.net>
align kconfig option CONFIG_ARC_CUSTOM_INIT to
CONFIG_INIT_ARCH_HW_AT_BOOT. Remove unused CONFIG_ARC_CUSTOM_INIT in
kconfig.
Signed-off-by: Yuguo Zou <yuguo.zou@synopsys.com>
Add support for the BuyDisplay 3.5" TFT + touch shield based on ILI9488
controller and FT6236 touch.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
UART IP is clocked with 50MHz on HAPS by default. So switch
UART clock-frequency from 100MHz to 50MHz for nsim_* boards
so the binaries can be run on HAPS as well.
This property is dummy in case run in simulator (nSIM) so we
don't need to change anything in nSIM configuration files.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
The nRF5340 (P)DK is equipped with the MX25R64 flash memory. Add a dts
node for that chip in the board definition as well as the missing QSPI
node in the nRF5340 SoC definition.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Update the board image file in the nrf5340 documentation,
reflecting the fact that we now document the nRF5340 DK
instead of the PDK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Update the docs of nRF5340 board, to point to the
nRF5340 DK instead of the PDK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Convert handful of users of DEVICE_INIT to DEVICE_DEFINE or
SYS_DEVICE_DEFINE to allow deprecation of DEVICE_INIT.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Update PWM pinctrl signal names of all non-F1 STM32 boards.
`pwm` variant is not available anymore on non-F1 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move the data/command GPIO from Arduino header 16 (D10), which collides
with Arduino SPI SS, to Arduino header 15 (D9).
Add commented example for specifying a reset GPIO on Arduino header 14
(D8).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
We deprecate nRF5340 PDK and add a note that
the board will be replaced by nRF5340 DK.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Nordic Dev Kit board names were changed in Zephyr
v2.3 release, following the standard Board deprecation
policy. Two releases later we do not need to keep
references to the old names in the boards' documentation.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This build target has all the low-memory options enabled for
memory management: a 4MB address space, 32-bit paging mode,
no KPTI, an empty page pool, and common page tables for
memory domains.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
These are set such that we have enough pages in the pool
for typical driver mappings and to instantiate two more
memory domains, which is what our tests require.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Replaces all existing variants of value clamping with the MIN and MAX
macros with the CLAMP macro.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
Add support for the recently introduced STM32CubeProgrammer runner.
Updated documentation to mention its availability as latest official
OpenOCD releases do not support H7 series.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
There is no user USB port available on these boards.
Remove support and remove files when no more needed.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Enables the fat_fs sample on the mm_swiftio board by adding a
board-specific Kconfig overlay, and adding sdhc to the list of
board-supported features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Following migration of pinctrl configuration from pinmux.c files
to device tree and deprecation of pinctrl defines, remove
pinmux.c files when possible.
Additionally remove the CMakeLists.txt files when it makes sense.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add Inventek es-WIFI modules shield. This shield exposes es-WIFI driver
using Arduino Uno R3 header by UART or SPI interfaces. It shows how
user can create their own overlay and expose es-WIFI driver.
The current Inventek's EVB doesn't have all pins necessary to control
the module by Arduino hearder. This shows how to wire to get ISM43xx
EVB working.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Update documention to refer to MEC152x specifications and
SPI image generator. MEC152x is the actual production SOC.
The only difference is the Boot-ROM loader SPI image layout.
Preserve the link to the old, MEC1501 SPI image generator.
Signed-off-by: Scott Worley <scott.worley@microchip.com>
Move STM32 based board USB pin configuration to device tree.
Exceptions:
* olimex_stm32_h407: Node not enabled and not documented.
Signal added in disabled node.
* L0/G4 based boards as signals are not available yet.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This qemu device is REALLY slow in icount mode. When I run it outside
of icount and watch the simulator advance the clock device in real
time, it looks to me like it expects the counter to be running at ~125
MHz. But it's set to a 12 MHz clock rate in its config, and trying to
use a 1000 Hz tick rate.
At those settings (and with the shift=3 argument to icount), I'm
measuring about 10k cycles to handle a minimal timer interrupt. But
if you do the math, that comes to 12k cycles per tick. The interrupt
takes as long as a tick! That would never work, except for the fact
that the timer driver on this device cheats and doesn't try to align
to ticks (basically ignoring all the lost time). And even that breaks
on the scheduler_api test (which does both tick and cycle math and
tries to compare them) when it's fixed to properly align itself.
One solution might be to set the clock rate to what qemu appears to
believe is the correct 125 MHz value. And that causes the test to
complete, but all tests now take ~10 minutes of real time because the
simulator is so slow!
So just make up some clock rates, it's a simulated platform after all.
I chose 5 MHz cycle time and 100 Hz tick rate, which on my device is
about half of "real" speed and very acceptable.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
Refactors nxp i.mx, kinetis, and lpc board-level device trees to use
DT_SIZE_K and DT_SIZE_M macros to define external memory sizes. This is
self documenting and easier to read.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
I2S signals should now be configured using dt.
For nucleo_f411re, I2S pins were configured using SPI definitions
that pulled the same strings behind the scene as I2S would have done.
This being said, only CK and SD pins should be needed and were
documented, so I only left those.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
This board has a multi-level power domain hierarchy where a sensor has
its own power control that is accessed through an external GPIO
peripheral that itself has a power control.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
In the flash partition definitions for ARM boards,
the link to the legacy partition macros does not
exist any more. The commit cleans up the partition
definition by removing this link.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
As a proof of concept, turn USB signals configuration to USB
for nucleo_wb5rg and disco_l475_iot1 boards.
This implicitly remove pull-up on _ID pin, which turn out to
have no side effect.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Sets the device tree chosen node for data tightly coupled memory (DTCM)
on i.mx rt boards that aren't already using DTCM as the chosen SRAM.
Leverages the common cortex-m linker section instead of the soc-specific
one.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removes the DATA_LOCATION Kconfig symbol from the i.mx rt soc series and
refactors corresponding boards to use a device tree chosen node instead.
The external SDRAM is chosen on all boards that can support it;
otherwise the internal DTCM is chosen.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
