Adds imx rt support.
Allows n-number of can interfaces based on device-tree.
Adds a "common" irq name.
Added CAN bus pins and dts for 1060 and 1064 EVK.
Signed-off-by: Rick Talbott <rtalbott@fastmail.com>
update rt6xx series sram mapping to skip 0x180000,
reserved for DSP usage.
this fixes tests/subsys/debug/coredump for this board
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Add IUART driver based on MCUX SDK. This driver is used to provide
serial console support on i.MX8M Mini SoC.
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
This commit adds the device tree nodes and bindings for the I2C
controllers of the LPC11U6X MCUs
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This commit adds basic support for the clock controller used in
lpc11u6x MCUs.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
This commit adds a bindings for the clock controller used in lpc11u6x
MCUs. It also adds a clock-controller node for the lpc11u6x soc series.
Signed-off-by: Maxime Bittan <maxime.bittan@seagate.com>
This patch adds the DT nodes and binding for the pinmux registers,
aka IOCON (I/O control), found on the LPC11U6x MCUs.
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
For true mmio-sram, arc,iccm, arc,dccm nodes we should not be setting
device_type = "memory". This should be used for true DRAM regions of
memory and not on SoC SRAMs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Enable GPIO as a workaround to enable some SPI slaves are not correctly
controlled using the Flexcomm SPI device.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Adds the required #io-channel-cells property to kinetis k8x and kv5x
socs. We are now consistently defining this property for all
nxp,kinetis-adc16 compatible nodes.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Allow configuring the clock prescaler divider for the NXP Kinetis
FlexTimer. Setting the prescaler to a lower value allows for much
higher resolution/accuracy for the generated PWM waveforms.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Instead of having a Kconfig property, if there is no local-mac-address
property in the devicetree than we'll generate a unique MAC address
based on unique ID registers on the SoC.
We remove the local-mac-address properties in the SoC dtsi files to
match the default behavior that existed before (ie, unique MAC address)
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Binding used for LPC random number generator hardware.
Describes RNG device node in LPC5xxx SoCs device tree peripherals.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Once the TPM driver and the required configs have been added,
now this patch enables the usage of the PWM framework on KW41Z
SoCs. As such, the DTS gets the proper nodes and the pinmuxing
is done according to the configuration requested.
Signed-off-by: Alex Porosanu <alexandru.porosanu@nxp.com>
Add device tree nodes for the Digital-to-Analog (DAC) modules present
in the NXP Kinetis K6x series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add device tree node for the Digital-to-Analog (DAC32) module present
in the NXP Kinetis KE1xF series.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add initial devicetree for the NXP LPC55S16. Only non-secure (ns)
access is supported for now.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Do not assume in the SoC level device trees that NXP Kinetis FlexTimer
nodes will always be configured as PWM. Instead, configure FlexTimer
nodes for PWM at the board level for NXP Kinetis boards.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
Replace DT_FLASH_DEV_NAME with DT_CHOSEN_ZEPHYR_FLASH_CONTROLLER_LABEL.
We now set zephyr,flash-controller in the chosen node of the device
tree to the flash controller device.
NOTE: For a SoCs with on die flash, this points to the controller and
not the 'soc-nv-flash' node. Typically the controller is the
parent of the 'soc-nv-flash' node).
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Convert driver to use DT_INST_ defines. As part of this conversion we
remove the Kconfig options for per GPIO controller enables and instead
get that information from device tree. This means we now disable each
GPIO controller by default in the DTS and have each board dts enable the
GPIO controller ports it needs.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
There was a typo bug in the SRAM ranges property that causes the SRAM
nodes to appear at the wrong addresses.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Mark all the individual PWMs as disabled in dts and enable the one
explicitly used on the mimxrt1064_evk.dts in the board dts file.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Move the majority of the device tree into nxp_lpc55S6x_common.dtsi and
use ranges to handle the different address may for non-secure.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Have nodelabels match the SoC docs so when a nodelabel reference is
made in the code its easier to relate to the SoC.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
