These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The old GCC ARM Embedded website on launchpad
(https://launchpad.net/gcc-arm-embedded) has been superseeded by the new
GNU Arm Embedded one
(https://developer.arm.com/open-source/gnu-toolchain/gnu-rm).
This also means a change of name from "GCC" to "GNU". Reflect this in
the enviroment variables so that the proper term is used henceforth.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In preparation for introducing a warning.
Unquoted string defaults work through a quirk of Kconfig (undefined
symbols get their name as their string value), but look confusing. It's
done inconsistently now too.
Suggested by Kumar Gala.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
FS_FLASH_MAP_STORAGE keyword enables the storage partition,
but it was depend on flash_map module which is unused by
NFFS. This patch makes it independent thanks
to it is possible to enable the storage partition
without flash_map module.
FS_FLASH_MAP_STORAGE was renamed to
CONFIG_FS_FLASH_STORAGE_PARTITION
as it is independent for flash_map.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The NFFS partition at the end of flash is also useful for any other
file system or even the Flash Circular Buffer (FCB). Rename the
partition from 'nffs_partition' to 'storage_partition' and make it
depend on a new hidden Kconfig entry which the relevant users will
select (such as NFFS and FCB).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The SAM0 SoC was switched to use DTS for SPI configuration. Update
documentation for the SAM0 based boards to use the correct SPI
controller device names.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Since not all boards enable all devices, we typically have the SoC dtsi
file have a device marked with status = "disabled" and have the
board.dts explicitly enable with status = "ok". Update it so USB on
Atmel SAMD21 work this way.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Switch the SoC device tree to define a single entry per SERCOM instead
of one per mode.
Define a Device Tree binding for the SAM0 SPI and use it instead of
Kconfig for enabling / disabaling instances
Switch the Arduino Zero, Adafruit Feather M0 Basic Proto, and
Trinket M0 to use the new defintion.
Add the APA102 LED that's on the Trinket as a test.
Signed-off-by: Michael Hope <mlhx@google.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
