Some files have moved from their original location, or are no longer
available. For the mbedtls samples, tweak the link to point to a page
where links for current and previous downloads can be found.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This commit fixes compile error caused by commit 39962dc9
"samples: use k_thread_create()"
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This https-client sample starts to send HTTP GET/HEAD/POST
requests same way as http-client, to https server that can
be found in net-tools repository.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Various network samples contained QEMU slip setup instructions
or those instructions were missing. A reference doc in
doc/subsystems/networking/qemu_setup.rst file already has the
setup instructions for QEMU. So add a reference to that file
in samples/net/*/README.rst files and remove unnecessary slip
setup instructions in relevant files.
Fix various typos in readme files at the same time.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add clarification that the DNS server configuration must be edited in
the respective prj.conf file.
JIRA: ZEP-2040
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
The number of RX and TX buffers is increased to 64 as the
earlier limit can cause memory exhaust in some cases.
Jira: ZEP-2223
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This fix is basically a no-op as the rx_buf pointer cannot be null
in practice, but in order to avoid Coverity complaining about
it add some null pointer checks to the UDP handling code.
Coverity-CID: 170124
Jira: ZEP-2235
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Waiting for an NET_EVENT_IF_UP before trying to connect isn't sufficient
in some cases; for instance, on devices using the MCUX HAL, such as the
FRDM-K64F, the interface will have the NET_IF_UP flag set even though
the link negotiation didn't yet complete.
Executing this sample on such board will produce the following output.
Notice the "Enabled 100M..." message right after trying to connect.
[dev/eth_mcux] [DBG] eth_0_init: MAC 00:04:9f:6f:91:da
net_context_connect error Is the server (broker) up and running?
[publisher:247] network_setup: -60 <ERROR>
Bye! [dev/eth_mcux] [INF] eth_mcux_phy_event: Enabled 100M
full-duplex mode.
Even though the returned error is ETIMEDOUT, increasing
net_context_connect()'s timeout parameter to several seconds isn't
sufficient; other steps performed by network_setup() after the link has
been fully established are necessary. As a stopgap measure, try
connecting a few times before giving up (more than one connection
attempt should be made by application in most cases, anyway.)
It might be the case that we need events to monitor ethernet link
(re)negotation in addition to the NET_IF_UP bit.
Jira: ZEP-2036
Signed-off-by: Leandro Pereira <leandro.pereira@intel.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
If the HTTPS connection is closed, then properly handle call to
HTTP parser init in case of error and also remove any pending
data that belong to old connection.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
There is not enough memory to run the HTTP server sample
application in Arduino-101 so remove the config file.
Jira: ZEP-2157
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit creates a HTTP server library. So instead of creating
a complex HTTP server application for serving HTTP requests, the
developer can use the HTTP server API to create HTTP server
insteances. This commit also adds support for creating HTTPS servers.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The net_sample_app_init() is now able to wait that both IPv4
and IPv6 addresses are setup before continuing.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
More general spelling fixes, and cleaning up stray UTF-8 characters
such as curly-quotes, em- and en-dashes. Use replacement strings
for |reg| and |trade|.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
This creates a common API for network sample applications for
setting up IP addresses etc. The HTTP client application is modified
to use this API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Instead of separate sample application that does everything
related to HTTP client connectivity, create a HTTP client library
that hides nasty details that are related to sending HTTP methods.
After this the sample HTTP client application is very simple and
only shows how to use the client HTTP API.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
We're moving the project code to GitHub folks, so change references
in the documentation from gerrit over to GitHub:
https://github.com/zephyrproject-rtos/zephyr
Change-Id: Ic491a62ed43fc799eb5698e92435cb6eb4d89394
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
The sample in its default configuration waits for DNS server
configuration via IPv4 or IPv6 specific means. Until this
information is receives, DNS querying won't even start. Make
diagnostic messages explicit of this fact, because if user
doesn't have required services available in the network, the
sample will appear to just hang.
Jira: ZEP-2061
Change-Id: I56a5b7354a2d1239a35d8334ed95a15ebd19254f
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
net_pkt_get_len() is the correct API to get network packet
length.
Jira: ZEP-2076
Change-Id: Ifff6f3d5df28b3684cc8bb3758f9e8bccd5d4534
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Add config file to be used for testing KW41Z's IEEE 802.15.4 driver.
Jira: ZEP-2026
Change-Id: I7042c57ad33ff72b35d24fbf28085b99b2301726
Signed-off-by: Bogdan Davidoaia <bogdan.davidoaia@linaro.org>
The dns_resolve sample application did not had project file for
two boards that the README file is talking about, so adding them here.
Jira: ZEP-2040
Change-Id: I68e825854a171b09d56df91ab80ce5d9349733f6
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
For stream-based protocols (TCP), adding less data than requested
("short write") is generally not a problem - the rest of data can
be sent in the next packet. So, make net_pkt_append() return length
of written data instead of just bool flag, which makes it closer
to the behavior of POSIX send()/write() calls.
There're many users of older net_pkt_append() in the codebase
however, so net_pkt_append_all() convenience function is added which
keeps returning a boolean flag. All current users were converted to
this function, except for two:
samples/net/http_server/src/ssl_utils.c
samples/net/mbedtls_sslclient/src/tcp.c
Both are related to TLS and implement mbedTLS "tx callback", which
follows POSIX short-write semantics. Both cases also had a code to
workaround previous boolean-only behavior of net_pkt_append() - after
calling it, they measured length of the actual data added (but only
in case of successful return of net_pkt_append(), so that didn't
really help). So, these 2 cases are already improved.
Jira: ZEP-1984
Change-Id: Ibaf7c029b15e91b516d73dab3612eed190ee982b
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Convert code to use u{8,16,32,64}_t and s{8,16,32,64}_t instead of C99
integer types.
Jira: ZEP-2051
Change-Id: I4ec03eb2183d59ef86ea2c20d956e5d272656837
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Most of these macros are not exactly exposing a buffer, but a specific
header pointer (ipv6, ivp4, ethernet and so on), so it relevant to
rename them accordingly.
Change-Id: I66e32f7c3f2bc75994befb28d823e24299a53f5c
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
- net_pkt becomes a stand-alone structure with network packet meta
information.
- network packet data is still managed through net_buf, mostly named
'frag'.
- net_pkt memory management is done through k_mem_slab
- function got introduced or relevantly renamed to target eithe net_pkt
or net_buf fragments.
- net_buf's sent_list ends up in net_pkt now, and thus helps to save
memory when TCP is enabled.
Change-Id: Ibd5c17df4f75891dec79db723a4c9fc704eb843d
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
There have been long lasting confusion between net_buf and net_nbuf.
While the first is actually a buffer, the second one is not. It's a
network buffer descriptor. More precisely it provides meta data about a
network packet, and holds the chain of buffer fragments made of net_buf.
Thus renaming net_nbuf to net_pkt and all names around it as well
(function, Kconfig option, ..).
Though net_pkt if the new name, it still inherit its logic from net_buf.
'
This patch is the first of a serie that will separate completely net_pkt
from net_buf.
Change-Id: Iecb32d2a0d8f4647692e5328e54b5c35454194cd
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
This is a start to move away from the C99 {u}int{8,16,32,64}_t types to
Zephyr defined u{8,16,32,64}_t and s{8,16,32,64}_t. This allows Zephyr
to define the sized types in a consistent manor across all the
architectures we support and not conflict with what various compilers
and libc might do with regards to the C99 types.
We introduce <zephyr/types.h> as part of this and have it include
<stdint.h> for now until we transition all the code away from the C99
types.
We go with u{8,16,32,64}_t and s{8,16,32,64}_t as there are some
existing variables defined u8 & u16 as well as to be consistent with
Zephyr naming conventions.
Jira: ZEP-2051
Change-Id: I451fed0623b029d65866622e478225dfab2c0ca8
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This can be useful to override the default value, for testing.
Change-Id: I23b559152c71955ff5aa6fd3643f1f40f5594194
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
DNS resolving is better done with DNS resolve API so remove
the DNS client API which is quite hard to use.
Change-Id: Ide4973a5be674414ea6e04a35c938195cce40b6a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Modify the code to use DNS resolve API instead of DNS client API
as the latter is being phased out.
Change-Id: I6a7618d770621fee1f502d2bc277a162c589108a
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
In order to test the coaps_server sample app on
Arduino 101 board.
Change-Id: I7b393dac03a8020b7bd515c3b5b2fd961940bc21
Signed-off-by: Wu Jiequan <jiequanx.wu@intel.com>
Added bt test code in the http_server sample app and in order
to test on Arduino 101 board, added prj_arduino_101.conf file.
Change-Id: Ie68a81ee809e8618f70b5fab6fdbd66692401014
Signed-off-by: Wu Jiequan <jiequanx.wu@intel.com>
The context buffer pool was introduced to deal with TCP holding buffers
when 6LO may modify them, therefore it makes sense to have it enabled
by default when TCP and 6LO are enabled given that the code can deal
with NULL pool in case the application don't implement one.
Change-Id: I600ca31ab40c96ee27937c2e885e332b0cee4995
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Atmel SAM family GMAC Ethernet driver is implementing zero-copy
networking. As a result it has to reserve a defined amount of RX
data net buffers before bringing up the interface. Since net buffer
pool is initialized by the network stack and this driver was bringing
the interface up in its initialization function the driver initialization
was performed, as a workaround, after network stack initialization. It
is not a clean solution. This patch fixes this by bringing the
interface up in interface initialization function. The driver itself
can now be initialized before the network stack is.
Tested on Atmel SMART SAM E70 Xplained board
Change-Id: I65886fd6db6f27a10628e393cfabd8e5f78c08ff
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>