Convert driver to use new DT_INST macros throughout. We remove the
aliases and use nodelabel instead in the soc_gpio.h to determine the
label for the specific gpio controller.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change to code to use the automatically generated DT_INST_*
defines and remove the now unneeded configs and fixups.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
The sole purpose of init options has been to enable hardware flow
control on NS16750 when asked. Use the proper DTS tags for this.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
This breaks down the GPIO controller definition in DTS into
multiple entries. This allows these controllers to be
referenced by other DTS, and test board overlay files.
And also we can remove the entries in the dts fixup file.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
generated_dts_board.h is pretty redundant and confusing as a name. Call
it devicetree.h instead.
dts.h would be another option, but DTS stands for "devicetree source"
and is the source code format, so it's a bit confusing too.
The replacement was done by grepping for 'generated_dts_board' and
'GENERATED_DTS_BOARD'.
Two build diagram and input-output SVG files were updated as well, along
with misc. documentation.
hal_ti, mcuboot, and ci-tools updates are included too, in the west.yml
update.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In order to avoid a warning from Sphinx complaining that the
supported_features.rst file is not included in any ToC, rename it to
.txt so that Sphinx understands that this is only a snippet to be
included in other files.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are two set of code supporting x86_64: x86_64 using x32 ABI,
and x86 long mode, and this consolidates both into one x86_64
architecture and SoC supporting truly 64-bit mode.
() Removes the x86_64:x32 architecture and SoC, and replaces
them with the existing x86 long mode arch and SoC.
() Replace qemu_x86_64 with qemu_x86_long as qemu_x86_64.
() Updates samples and tests to remove reference to
qemu_x86_long.
() Renames CONFIG_X86_LONGMODE to CONFIG_X86_64.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This will be used for both 32-bit and 64-bit mode.
This header gets pulled in by x86's arch/cpu.h, so put
it in include/arch/x86/.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add duplicate per-CPU data structures (x86_cpuboot, tss, stacks, etc.)
for up to 4 total CPUs, add code in locore and z_arch_start_cpu().
The test board, qemu_x86_long, now defaults to 2 CPUs.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This driver was still using CONFIG_* values to determine its address,
IRQ, etc. Add a binding for an "intel,hpet" device and migrate this
driver to devicetree.
Fixes: #18657
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Add qemu_x86_long board (with CONFIG_X86_LONGMODE=y) for testing.
This requires adding support to soc/ia32 for long mode (trivial),
and adding a quick 64- to 32-bit ELF conversion before invoking
QEMU, which apparently doesn't like 64-bit kernel files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The previous linker script was barebones and non-standard. It is
replaced with a script conforms to the rest of the Zephyr arches,
utilizing include/linker headers and standard macros.
link-tool-gcc.h is updated to account for the "i386:x86-64" arch and
the generation of 64-bit ELF binaries.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This patch adds basic build infrastructure, definitions, a linker
script, etc. to use the Zephyr and 0.10.1 SDK to build a 64-bit
ELF binary suitable for use with GRUB to minimally bootstrap an
Apollo Lake (e.g., UpSquared) board. The resulting binary can hardly
be called a Zephyr kernel as it is lacking most of the glue logic,
but it is a starting point to flesh those out in the x86 tree.
The "kernel" builds with a few harmless warnings, both with GCC from
the Zephyr SDK and with ICC (which is currently being worked on in
a separate branch). These warnings are either related to pointer size
differences (since this is an LP64 build) and/or dummy functions
that will be replaced with working versions shortly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Update the -march flag passed to the compiler to reflect the
underlying microarchitecture is 'goldmont'.
Fixes: #17104
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
XIP support in x86 was something of a mess. This
patch does the following:
- Generic ia32 SOC no longer defines a "flash" region
as generic X86 devices don't have a microcontroller-
like concept of flash. The same has been done for apollo_lake.
- Generic ia32 and apollo_lake SOCs starts memory at 1MB.
- Generic ia32 SOC may optionally have CONFIG_XIP enabled.
The board definition must provide a flash region definition
that gets exposed as DT_PHYS_LOAD_ADDR.
- Fixed definitions for RAM/ROM source addresses in ia32's
linker.ld when XIP is turned off.
- Support for enabling XIP on apollo_lake SOC removed, there's
no use-case.
- acrn and gpmrb boards have flash and XIP related definitions
removed.
- qemu_x86 has a fake flash region added, immediately after system
RAM, for use when XIP is enabled. This used to be in the ia32 SOC.
However, the default for qemu_x86 is to now have XIP disabled.
- Fixed tests/kernel/xip to run by default on boards that enable
XIP by default, plus an additional test to exercise XIP on
qemu_x86 (which supports it but has XIP switched off by default)
The overall effect of this patch is to:
- Remove XIP configuration for SOC/boards where it does not make
any sense to have it
- Support testing XIP on qemu_x86 via tests/kernel/xip, but leave
it off by default for other tests, to ensure it doesn't bit-rot
and that the system works in both scenarios.
- XIP remains an available feature for boards that need it.
Fixes: #18956
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
The documentation for the GPMRB incorrectly made reference to the
up_squared board in its high-speed UART configuration section. We
consolidate the related documentation for all boards based on the
Apollo Lake SoC and adjust the language to be more generic.
Fixes: #18808
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Removes very complex boot-time generation of page tables
with a much simpler runtime generation of them at bootup.
For those x86 boards that enable the MMU in the defconfig,
set the number of page pool pages appropriately.
The MMU_RUNTIME_* flags have been removed. They were an
artifact of the old page table generation and did not
correspond to any hardware state.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
This board and SoC was discontinued some time ago and is currently not
maintained in the zephyr tree.
Remove all associated configurations and variants from the tree.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The uart_qmsi driver used system clock frequency
as a base for baudrate calculation. This commit corrects
that by obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The spi_dw driver used system clock frequency
as a base for SPI bus frequency calculation.
This commit corrects that by obtaining the needed value from DTS.
Signed-off-by: Piotr Zięcik <piotr.ziecik@nordicsemi.no>
The MVIC is no longer supported, and only the APIC-based interrupt
subsystem remains. Thus this layer of indirection is unnecessary.
This also corrects an oversight left over from the Jailhouse x2APIC
implementation affecting EOI delivery for direct ISRs only.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This file is 32-bit specific, so it is moved into the ia32/ directory
and references to it are updated accordingly.
Also, SP_ARG* definitions are no longer used, so they are removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move uart.h to drivers/uart.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move ipm.h to drivers/ipm.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move power.h to power/power.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Move internal and architecture specific headers from include/drivers to
subfolder for interrupt_controller:
include/drivers/interrupt_controller/
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Removed Quark D2000 SoC files and first-order related DT bindings.
A few config options have been moved from the CONFIG_* space to
the DT_* space, as they were defined in the D2000 Kconfig files
and "leaked" into the other Quark trees.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Add board support (and documentation) for the Intel Gordon Peak
Module Reference Board, a dev board based on the Apollo Lake SoC.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The Apollo Lake SoC no longer uses the legacy PCI driver, so remove
references and supporting code.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
While enabling specific I2C ports does indeed belong at the board
level Kconfig, the selection of driver (I2C_DW) is an SoC-level
choice, so it is moved accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
Which UARTs are broken out from the SoC on a particular board is
board-specific; don't enable UARTs blindly in the SoC Kconfig.
Also, the default UART options are specified in the driver Kconfig, so
the same defaults specified in the SoC Kconfig are redundant. Removed.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The UART references in dts_fixup.h are actually SoC-specific, not
board-specific, so they are moved. Since this leaves the board fixups
empty, the file is removed.
The SoC fixups are expanded to include the additional two ports that
are present on some revisions of the Apollo Lake.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
If the QMSI is not configured in (in the west manifest) we get kconfig
whitelisting errors because the type is declared within the module
itself.
Change default to def_bool to set the type.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
