The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
With latest SDK release v0.11.3 basic SMP support for HSDK
board was introduced in OpenOCD. Lets enable smp in openocd.cfg,
so using west we would be able to run Zephyr on all 4 cores.
Signed-off-by: Evgeniy Didin <didin@synopsys.com>
* current supported boards:
* emsk, iotdk, nsim, emsdp, hsdk.
* for the unsupported future boards, pls take a
reference of supported boards' board.cmake.
* mdb runner is required and the default runner for SMP
case, e.g., HSDK and nsim_hs_smp.
* other ARC boards can also choose to use mdb by
setting runner as mdb, e.g. west flash --runner mdb.
* with mdb runner, user can make a debug through mdb gui
* with arc_nsim or opencod runner (default runner), user
can make a debug through gdb cmdline.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
The ILITEK ILI9340 should have been in the dts and added as #defines in
dts_fixup.h. Fix this by adding a display node in the dts.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Now when ARC development boards are switched to generic OpenOCD
runner we need to explicitly instruct the runner to load Elf but not
binary image (which is a default for OpenOCD runner).
This might be done either manually adding "--use-elf" option to
west's command line or that might be added by default fro affected
boards, which we do exactly now.
Fixes https://github.com/zephyrproject-rtos/zephyr/issues/22888.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Some ARC deveopment boards have q bit funny memory maps.
For example IoT Development Kit board has those areas
that we use in Zephyr:
1. 256 KiB of ICCM @ 0x2000_0000 for code
(i.e. ".text" section goes here)
2. 128 KiB of DCCM @ 0x8000_0000 for data
(i.e. ".data" section goes here)
And so objcopy dumps 0x6000_0000 bytes (which is ~ 1.5Gib or raw data)
in zephyr.hex which gives us ~ 4.3 GiB of resulting zephyr.hex size.
W/o gap filling we're back at normal tens of KiB.
Given we have currently no need to fill the gaps anyways we disable it
for all ARC devboards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The last core which gets initilaized is used by default by OpenOCD.
Thus if we leave configuration as it was we'll get single-core
binaries executed by core3 while we expect core0 to be used.
We didn't see that problem reviously because we used to use
GDB for binary (actually Elf) loading and execution and there in GDB
we explicitly connected to the OpenOCD port wired to core 0.
Now with "west flash" we use OpenOCD for loading anr running and
we need everything setup correctly from the beginning.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to use "em-starterkit" runner for ARC which is
basically heavy-modified "openocd" runner tweaked to
use GDB for loading and starting Elf files.
Now when loading and running Elf files is possible with generic
"openocd" runner we may us it. So we switch and get rid of
"em-starterkit" as well since we no longer need it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
To be used in setups with multiple boards attached to the same one
host we need to have an ability to specify precisely which JTAG probe
to use for a particular board.
This is done by passing "ftdi_serial XXX" command to OpenOCD.
And the serial ("XXX") is supposed to be passed from higher level,
typically via west's options.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
All board defconfig files currently set the architecture in addition to
the board and the SoC, by setting e.g. CONFIG_ARM=y. This spams up
defconfig files.
CONFIG_<arch> symbols currently being set in configuration files also
means that they are configurable (can be changed in menuconfig and in
configuration files), even though changing the architecture won't work,
since other things get set from -DBOARD=<board>. Many boards also allow
changing the architecture symbols independently from the SoC symbols,
which doesn't make sense.
Get rid of all assignments to CONFIG_<arch> symbols and clean up the
relationships between symbols and the configuration interface, like
this:
1. Remove the choice with the CONFIG_<arch> symbols in arch/Kconfig and
turn the CONFIG_<arch> symbols into invisible
(promptless/nonconfigurable) symbols instead.
Getting rid of the choice allows the symbols to be 'select'ed (choice
symbols don't support 'select').
2. Select the right CONFIG_<arch> symbol from the SOC_SERIES_* symbols.
This makes sense since you know the architecture if you know the SoC.
Put the select on the SOC_* symbol instead for boards that don't have
a SOC_SERIES_*.
3. Remove all assignments to CONFIG_<arch> symbols. The assignments
would generate errors now, since the symbols are promptless.
The change was done by grepping for assignments to CONFIG_<arch>
symbols, finding the SOC_SERIES_* (or SOC_*) symbol being set in the
same defconfig file, and putting a 'select' on it instead.
See
https://github.com/ulfalizer/zephyr/commits/hide-arch-syms-unsquashed
for a split-up version of this commit, which will make it easier to see
how stuff was done. This needs to go in as one commit though.
This change is safer than it might seem re. outstanding PRs, because any
assignment to CONFIG_<arch> symbols generates an error now, making
outdated stuff easy to catch.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Remove leading/trailing blank lines in .c, .h, .py, .rst, .yml, and
.yaml files.
Will avoid failures with the new CI test in
https://github.com/zephyrproject-rtos/ci-tools/pull/112, though it only
checks changed files.
Move the 'target-notes' target in boards/xtensa/odroid_go/doc/index.rst
to get rid of the trailing blank line there. It was probably misplaced.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
* add pinmux driver. hsdk board has arduino, mikrobus and
pmod interfaces, which can be confiured for different function,
such as: gpio, spi, uart, iic.
* add introduction for arduino, mikrobus and pmod interfaces.
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
This commit includes the initial support of ARC HS Development Kit:
* hsdk soc support
* hsdk board support
* no mmu support, so no userspace
* smp support
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
