USB MSC sample has been expanded over time. Config overlays
for RAM disk and flash disks were added. Board specific overlays
followed. It was overlooked that they forced a specific
configuration for the nrf52840dk_nrf52840 board,
even if it was not explicitly desired
(for example RAM-disk). This also caused strange behaviour
during automatic MSC USB3CV tests (which explicit selects RAM-disk)
so that nrf5340dk_nrf5340_cpuapp board passed test
but nrf52840dk_nrf52840 failed.
Rework disk and file system configuration, and initialization
code, allow to use FAT file system on top of RAM disk.
This sample can be built with none or one of two supported
file systems, LittleFS or FATFS. Disk subsystem can be flash
or RAM based. LittleFS only works with flash disk.
There are four useful possibilities:
- RAM disk without any file system for testing (default)
- RAM disk with FAT file system
- flash disk with FAT file system
- flash disk with LittleFS
Flash disk configurations is only available (as before) for
nordic,qspi-nor compatible, but only need the device tree overlay
per platform without a config overlay.
This path also revises test cases.
Remove invalid "flash" tag from depends_on key.
Remove unnecessary gpio tag and exclude native platform.
Resolves: #26275
Signed-off-by: Johann Fischer <johann.fischer@nordicsemi.no>
Deactivate all features that are not absolutely needed to run
the shell.
Used CONFIG_CBPRINTF_NANO library to save 1020B.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordicsemi.no>
Configurations for additional smp_svr sanity builds have been added
to limit possibility of getting not compilable smp_svr sample.
Signed-off-by: Dominik Ermel <dominik.ermel@nordicsemi.no>
Extends the Segger SystemView configuration for the tracing sample to
more platforms that support Segger RTT, not just nrf52840dk_nrf52840.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Extracts the Segger SystemView configuration for the tracing sample from
sample.yaml into a separate file. Increases the idle thread stack size
to fix overflows observed on i.MX RT boards. Removes
CONFIG_USE_SEGGER_RTT=y which is selected by CONFIG_SEGGER_SYSTEMVIEW.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Enables the fat_fs sample on the mm_swiftio board by adding a
board-specific Kconfig overlay, and adding sdhc to the list of
board-supported features.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
WebUSB sample is using BOS descriptor. Because of that
the bcdUSB field of device descriptor is set to 0x0210.
This requires for the BOS descriptor to have LPM support.
LPM support use additional descriptor that the HOST can
read by requesting BOS desc. The descriptor is called
Extension descriptor and is specified in `USB Link Power
Management ECN` document considered a part of USB 2.0
spec.
This patch adds missing part of the BOS descriptor and
fixes issue with webUSB sample not passing i'LPM L1 Suspend
Resume Test' from USB3CV test tool.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
In the flash partition definitions for ARM boards,
the link to the legacy partition macros does not
exist any more. The commit cleans up the partition
definition by removing this link.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Split CP and PD samples into dedicated directories as the difference
between the two are expected to grow with time. Also, do some
refactoring.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Minimize number of exported methods by unifying all osdp_cp_send_cmd_*()
as osdp_cp_send_command().
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
The legacy macros were first deprecated in Zephyr v2.3. Now that
Zephyr v2.4 has been released, that makes two releases where these
macros have been deprecated, so it's OK to remove them.
This leaves support for legacy binding syntax in place. Removing that
is left to future work.
We need to update various pieces of documentation related to flash
partitions that never got updated when the new API was introduced.
Consolidate this information in the flash_map.h API reference page,
since that's really where users will run into it. This also gives us
the opportunity to improve this documentation.
Adjust a couple of kconfigfunctions.py and sanitycheck bits to use
non-legacy edtlib APIs.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
After HW stack protection option was globally enabled for
nRF SoCs turned out main stack size is too small for
USB mass storage sample. Increase to avoid overflow.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Remove obsolete include of the shell_uart.h file.
It is sufficient to include the shell.h file.
Signed-off-by: Jakub Rzeszutko <jakub.rzeszutko@nordisemi.no>
Instead if printing the line number, output the context (thread,
semaphore, mutex, ..) and the ID of the event where applicable.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The test for this sample requires a usb connection to a secondary port,
output is not captured on the default usb port.
Fixes#28154
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
The CANopenNode stack function CO_delete() takes a void
*CANdriverState argument. This maps to a pointer to a struct
canopen_context in Zephyr.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
A change to the previous partition resulted in the unit address being
inconsistent with the reg property.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
When running shell commands updatehub alloc data from shell stack.
Increase shell room stack to avoid shell issues. Memory tuning
should be performed accord with available resources.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
This commit extends USB hid API callbacks by adding
'const struct device *dev' parameter. If the application
configured more than one HID device then it must specify
separate hid_ops for each device as its unable to determine
for which device the callback was called.
This patch makes it possible to have only one hid_ops within
the application and the application is aware for which device
the callback was called because of explicit device pointer.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Some of the names used in `struct osdp_cmd` where directly as in the
specification. Initially it appealed to keep them like that but with
time, a little more consistent naming of members helps if you haven't
read the specification document very recently.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
Add a OSDP CP mode sample that sends out a periocic command to a
connected PD. It also demosnstrates key press and card read callback
registration.
Signed-off-by: Siddharth Chandrasekaran <siddharth@embedjournal.com>
nRF53 application core does not have RNG peripheral.
Software implementation must be used instead.
This patch adds config overlay for hid-cdc nRF5340 sample.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Now that device_api attribute is unmodified at runtime, as well as all
the other attributes, it is possible to switch all device driver
instance to be constant.
A coccinelle rule is used for this:
@r_const_dev_1
disable optional_qualifier
@
@@
-struct device *
+const struct device *
@r_const_dev_2
disable optional_qualifier
@
@@
-struct device * const
+const struct device *
Fixes#27399
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Add configuration and overlay files for Adafruit feather nRF52840.
README has also been updated and improved. Documentation related to
littlefs has been moved to an independent section as it could apply to
any sample.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Following the change to use the C domain for parsing, update all
existing :cpp:func: references to :c:func:. Remove the parentheses as
well, if used, because they are not needed, this is already known to be
a function, and how it is displayed in the documentation later is a
semantic decision done by the output builder.
Signed-off-by: Fabio Utzig <fabio.utzig@nordicsemi.no>
Make the flash-backed USB mass storage sample depend on usb_device and
flash instead of just flash.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
When try build updatehub using overlay-dtls.conf system fail with
cannot create privkey.der.inc file, permission denied. Add missing
gen_dir cmake definition. Update updatehub sample test config to
run missing dtls build test.
Signed-off-by: Gerson Fernando Budke <gerson.budke@ossystems.com.br>
Add overlay that includes only the shell transport of mcumgr, without
bringing in BLE as well. This can be used as an alternative for the
serial transport. The `smp_svr` README was updated accordingly.
Signed-off-by: Fabio Utzig <fabio.utzig@nordicsemi.no>
Its possible to rename the executable we build via the Kconfig symbol
CONFIG_KERNEL_BIN_NAME. So we really should use ${KERNEL_ELF_NAME},
${KERNEL_BIN_NAME} and ${KERNEL_HEX_NAME} variables instead of hardcoded
zephyr.elf, zephyr.bin, and zephyr.elf.
This fixes an build issue with
tests/misc/test_build/buildsystem.kconfig.utf8_in_values on
up_squared_adsp and lpcxpresso11u68 platforms.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
usb_enable() must be called by the application.
The application may want to register usb_dc_status_callback
and trace usb status codes (usb_dc_status_code).
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This patch removes unused Kconfig option from console
subsystem. If application wants to wait until the console
port is connected, enabled and ready to receive data
it should use uart_line_ctrl_get() API function and
check for DTR flag.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
