Make sure to retry at least once after the timeout elapses. Sample the
current time before starting the i2c transaction, and only give up if
the polling occurred after the timeout.
The timeout exists to allow the eeprom time to complete a write, during
which time it will nack transactions (at24) or the status register will
report busy (at25). If a transaction fails legitimately, but the 1ms
sleep overshoots the timeout expiration, we will not try again, which
fails to give the part the full grace period before declaring failure.
This is likely to happen in the last 1ms interval but also possible if
the eeprom thread is preempted. It is possible to only try once and give
up if the sleep lasts longer than the timeout, which fails to give the
part an adequate period to complete the write.
Waiting until the current time is after (not equal to) the timeout is
also important because we don't want to round up partial milliseconds if
the start time was sampled near the end of a millisecond boundary. The
timeouts of eeproms can be ~5ms.
Signed-off-by: Tyler Hall <tylerwhall@gmail.com>
Usually, we want to operate only on "available" device
nodes ("available" means "status is okay and a matching binding is
found"), but that's not true in all cases.
Sometimes we want to operate on special nodes without matching
bindings, such as those describing memory.
To handle the distinction, change various additional devicetree APIs
making it clear that they operate only on available device nodes,
adjusting gen_defines and devicetree.h implementation details
accordingly:
- emit macros for all existing nodes in gen_defines.py, regardless
of status or matching binding
- rename DT_NUM_INST to DT_NUM_INST_STATUS_OKAY
- rename DT_NODE_HAS_COMPAT to DT_NODE_HAS_COMPAT_STATUS_OKAY
- rename DT_INST_FOREACH to DT_INST_FOREACH_STATUS_OKAY
- rename DT_ANY_INST_ON_BUS to DT_ANY_INST_ON_BUS_STATUS_OKAY
- rewrite DT_HAS_NODE_STATUS_OKAY in terms of a new DT_NODE_HAS_STATUS
- resurrect DT_HAS_NODE in the form of DT_NODE_EXISTS
- remove DT_COMPAT_ON_BUS as a public API
- use the new default_prop_types edtlib parameter
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
We want to limit DT_ prefix to macros from devicetree.h and generation.
So rename DT_INST_AT2X* to just INST_DT_AT2X*.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
DT_CALL_WITH_ARG() is an internal implementation detail that should
not be used outside of devicetree.h.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
This reverts commit 8739517107.
Pull Request #23437 was merged by mistake with an invalid manifest.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Replace all occurences of BUILD_ASSERT_MSG() with BUILD_ASSERT()
as a result of merging BUILD_ASSERT() and BUILD_ASSERT_MSG().
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Document and assign write-protect signal as active low, and use the
active-sensitive API to control it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
