mirror of
https://github.com/zephyrproject-rtos/zephyr
synced 2025-08-12 10:06:00 +00:00
c0baad2262
Original name was too generic and confusing. This patch renames driver to pipe UART and moves it to console drivers folder. Kconfig destription is also improved. Change-Id: I716fdbf7d636bbdc03b0fce27a59fd866f473246 Signed-off-by: Szymon Janc <ext.szymon.janc@tieto.com>
112 lines
2.5 KiB
C
112 lines
2.5 KiB
C
/** @file
|
|
* @brief Pipe UART driver
|
|
*
|
|
* A pipe UART driver allowing application to handle all aspects of received
|
|
* protocol data.
|
|
*/
|
|
|
|
/*
|
|
* Copyright (c) 2015 Intel Corporation
|
|
*
|
|
* Licensed under the Apache License, Version 2.0 (the "License");
|
|
* you may not use this file except in compliance with the License.
|
|
* You may obtain a copy of the License at
|
|
*
|
|
* http://www.apache.org/licenses/LICENSE-2.0
|
|
*
|
|
* Unless required by applicable law or agreed to in writing, software
|
|
* distributed under the License is distributed on an "AS IS" BASIS,
|
|
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
|
|
* See the License for the specific language governing permissions and
|
|
* limitations under the License.
|
|
*/
|
|
|
|
#include <nanokernel.h>
|
|
|
|
#include <board.h>
|
|
#include <uart.h>
|
|
|
|
#include <console/uart_pipe.h>
|
|
#include <misc/printk.h>
|
|
|
|
#if !defined(CONFIG_UART_PIPE_INDEX) || !defined(CONFIG_UART_PIPE_IRQ)
|
|
#error One or more required values for this driver are not set.
|
|
#else
|
|
#define UART (uart_devs[CONFIG_UART_PIPE_INDEX])
|
|
|
|
static uint8_t *recv_buf;
|
|
static size_t recv_buf_len;
|
|
static uart_pipe_recv_cb app_cb;
|
|
static size_t recv_off;
|
|
|
|
void uart_pipe_isr(void *unused)
|
|
{
|
|
ARG_UNUSED(unused);
|
|
|
|
while (uart_irq_update(UART) && uart_irq_is_pending(UART)) {
|
|
int rx;
|
|
|
|
if (!uart_irq_rx_ready(UART)) {
|
|
continue;
|
|
}
|
|
|
|
rx = uart_fifo_read(UART, recv_buf + recv_off,
|
|
recv_buf_len - recv_off);
|
|
if (!rx) {
|
|
continue;
|
|
}
|
|
|
|
/*
|
|
* Call application callback with received data. Application
|
|
* may provide new buffer or alter data offset.
|
|
*/
|
|
recv_off += rx;
|
|
recv_buf = app_cb(recv_buf, &recv_off);
|
|
}
|
|
}
|
|
|
|
int uart_pipe_send(const uint8_t *data, int len)
|
|
{
|
|
return uart_fifo_fill(UART, data, len);
|
|
}
|
|
|
|
IRQ_CONNECT_STATIC(uart_pipe, CONFIG_UART_PIPE_IRQ,
|
|
CONFIG_UART_PIPE_INT_PRI, uart_pipe_isr, 0,
|
|
UART_IRQ_FLAGS);
|
|
|
|
static void uart_pipe_setup(struct device *uart, struct uart_init_info *info)
|
|
{
|
|
uart_init(uart, info);
|
|
|
|
uart_irq_rx_disable(uart);
|
|
uart_irq_tx_disable(uart);
|
|
IRQ_CONFIG(uart_pipe, uart_irq_get(uart), 0);
|
|
irq_enable(uart_irq_get(uart));
|
|
|
|
/* Drain the fifo */
|
|
while (uart_irq_rx_ready(uart)) {
|
|
unsigned char c;
|
|
|
|
uart_fifo_read(uart, &c, 1);
|
|
}
|
|
|
|
uart_irq_rx_enable(uart);
|
|
}
|
|
|
|
void uart_pipe_register(uint8_t *buf, size_t len, uart_pipe_recv_cb cb)
|
|
{
|
|
struct uart_init_info info = {
|
|
.options = 0,
|
|
.sys_clk_freq = CONFIG_UART_PIPE_FREQ,
|
|
.baud_rate = CONFIG_UART_PIPE_BAUDRATE,
|
|
.irq_pri = CONFIG_UART_PIPE_INT_PRI,
|
|
};
|
|
|
|
recv_buf = buf;
|
|
recv_buf_len = len;
|
|
app_cb = cb;
|
|
|
|
uart_pipe_setup(UART, &info);
|
|
}
|
|
#endif
|