Add a pwm0 entry and PWM support for the RGB LED so that the
rgb_led and fade_led demos work on the nrf52840_pca10059.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
MEC1501modular doesn't expose same I2C instances than MEC15xxevb,
additionally this causes undesired reconfiguration of pins with
other function when card is mated with a platform that complies
with MECC specification.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
Newer XDS firmware fails to flash correctly with higher adapter clock
speed. Using a slower speed for now to prevent errors.
Fixes#21372
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
Newer XDS firmware fails to flash correctly with higher adapter clock
speed. Using a slower speed for now to prevent errors.
Fixes#21372
Signed-off-by: Vincent Wan <vincent.wan@linaro.org>
When using internal IEEE 802.15.4 transceiver AT86RF233 at SPI speeds
above 6MHz was detected that frame buffer read returns corrupted data.
This set spi-max-frequency to 6MHz at atsamr21_xpro.dts to ensure best
relation of performance vs reliability.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
On Atmel SAM family the watchdog peripheral is enabled by default. To
ease maintenance of tests and samples, which typically don't handle
watchdog, disable the watchdog during the boot.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
Remove all "supported: -hwinfo" definitions from the boards
yaml files and documentation. hwinfo can generally be tested
on every board because it returns -ENOTSUP if not supported.
Signed-off-by: Alexander Wachter <alexander@wachter.cloud>
The LIS3MDL driver handles DRDY interrupt only. So connect
trigger to the DRDY pin instead of the INT pin.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Set the size of the storage partition in flash used by the NVS example
to 3 times the erase-block-size for this SoC family. In this case a
total of 12KB (as 3 erase-block-sizes is the minimum).
Signed-off-by: Oane Kingma <o.kingma@interay.com>
The method used to link code partition, as defined by
zephyr,code-partition has been modified in Zephyr 1.14. Remove any
remaining, outdated documentation that was embedded in the board dts
files.
Signed-off-by: Piotr Mienkowski <piotr.mienkowski@gmail.com>
This change also addresses issue# 21756 tests/obj_tracin where the
expected thread count does not match because kscan module is enabled
in this board. The Microchip kscan driver is contributing to the total
thread count, therefore interfering with the expected test result.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
This change addresses issue# 21756 where the expected thread
count does not match because kscan module is enabled in this board.
The Microchip kscan driver is contributing to the total thread count,
therefore interfering with the expected test result.
Signed-off-by: Francisco Munoz <francisco.munoz.ruiz@intel.com>
Now when ARC development boards are switched to generic OpenOCD
runner we need to explicitly instruct the runner to load Elf but not
binary image (which is a default for OpenOCD runner).
This might be done either manually adding "--use-elf" option to
west's command line or that might be added by default fro affected
boards, which we do exactly now.
Fixes https://github.com/zephyrproject-rtos/zephyr/issues/22888.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Created unit tests for the encryption and decryption functions.
Tested with the peripheral and with central_hr samples.
Due to latency of CAUv3 when used as CCM inline accelerator
only one of the PDU can be encrypted/decrypted within an
bilateral exchange M->S + S->M in a connection event.
If the RXed PDU is encrypted, the TXed PDU must be empty
with More Data if there is data in the LLL queue.
The TXed PDU will be encrypted when an empty PDU is RXed.
Signed-off-by: Cristi Caciuloiu <cristian.caciuloiu@nxp.com>
Update Atmel SAM-BA link address to MHCP SAM-BA web page. Now user will
navigate to right page instead be at MHCP home page.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Fix up the board definition so that the actual board can at least be
processed by Kconfig.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In the default configuration we want to enable the generic GPIO module
so that we avoid Kconfig warnings.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
In order to overrdie a choice one needs to define it again. Override it
by redefining it in the .defconfig file.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
For the non-secure image, the architecture still supports secure
execution, so express that in the defconfig.
See #22474.
Signed-off-by: Carles Cufi <carles.cufi@nordicsemi.no>
Some ARC deveopment boards have q bit funny memory maps.
For example IoT Development Kit board has those areas
that we use in Zephyr:
1. 256 KiB of ICCM @ 0x2000_0000 for code
(i.e. ".text" section goes here)
2. 128 KiB of DCCM @ 0x8000_0000 for data
(i.e. ".data" section goes here)
And so objcopy dumps 0x6000_0000 bytes (which is ~ 1.5Gib or raw data)
in zephyr.hex which gives us ~ 4.3 GiB of resulting zephyr.hex size.
W/o gap filling we're back at normal tens of KiB.
Given we have currently no need to fill the gaps anyways we disable it
for all ARC devboards.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
The last core which gets initilaized is used by default by OpenOCD.
Thus if we leave configuration as it was we'll get single-core
binaries executed by core3 while we expect core0 to be used.
We didn't see that problem reviously because we used to use
GDB for binary (actually Elf) loading and execution and there in GDB
we explicitly connected to the OpenOCD port wired to core 0.
Now with "west flash" we use OpenOCD for loading anr running and
we need everything setup correctly from the beginning.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to use "em-starterkit" runner for ARC which is
basically heavy-modified "openocd" runner tweaked to
use GDB for loading and starting Elf files.
Now when loading and running Elf files is possible with generic
"openocd" runner we may us it. So we switch and get rid of
"em-starterkit" as well since we no longer need it.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
To be used in setups with multiple boards attached to the same one
host we need to have an ability to specify precisely which JTAG probe
to use for a particular board.
This is done by passing "ftdi_serial XXX" command to OpenOCD.
And the serial ("XXX") is supposed to be passed from higher level,
typically via west's options.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Same deal as in commit eddd98f811 ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for the remaining cases outside defconfig
files. See that commit for an explanation.
Will do the defconfigs separately in case there are any complaints
there.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Same deal as in commit eddd98f ("kconfig: Replace some single-symbol
'if's with 'depends on'"), for all symbols defined within defconfig
files. See that commit for an explanation.
Maybe 'if's were used originally to mirror the 'if's in the main Kconfig
files, and then it got copied around by people assuming 'if' must work
differently from 'depends on'. It doesn't match in every spot at least.
Better to keep it simple and just consistently use 'depends on' when
it's a single symbol/choice I think. Helps reinforce that 'if' isn't
magic too.
Verified by printing all Kconfig menu nodes (symbols, choices, menus,
etc.) before and after the change and diffing (should show no
difference).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
