This makes the output of file2hex.py deterministic by default while also
letting the user set the mtime in the gzip header manually if desired.
Use the option without any argument to restore the previous behavior
that sets the current (and obviously changing) "now" timestamp.
To test: ./sanitycheck --tag gen_inc_file
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
If the compiler supports it, strip the ${ZEPHYR_BASE} prefix from the
__FILE__ macro used in __ASSERT* macros, in the
.noinit."/home/joe/zephyr/fu/bar.c" section names and in any application
code. This saves some memory, stops leaking user locations in binaries,
makes failure logs more deterministic and most importantly makes builds
more deterministic.
- .noinit section names now look like this in objdump -h:
17 .noinit."./kernel/init.c".2 00001100 00000000 ...
18 .noinit."./kernel/init.c".1 00001200 00000000 ...
19 .noinit."./kernel/init.c".3 00001800 00000000 ...
- The output of __ASSERT* macros now looks like this:
ASSERTION FAIL [0] @ ./samples/hello_world/src/main.c:13
The world comes crashing down
***** Kernel Panic! *****
Current thread ID = 0x00400040
Signed-off-by: Marc Herbert <marc.herbert@intel.com>
This commit enable Bluetooth SMP Service which will help
us to do Device Firmware Upgrade over thr air. By default
it is not enable.
Reference: $zephyr/samples/subsys/mgmt/mcumgr/smp_svr
Signed-off-by: Vikrant More <vikrant8051@gmail.com>
General MIC fix for AAD lengths up to 14 bytes.
This case doesn't concern the mesh stack because it uses 16 bytes.
Signed-off-by: Reham Tarek <reham.tarek@si-vision.com>
This stores the database hash and check if it has changed on commit
skipping service changed if hash matches.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Custom handlers without any arguments don't since there is a check for
argc > 1, to fix this behavior removing the check.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
If handle is over the range end return since handles are always placed
in ascending order.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
This reduces bt_gatt_foreach_attr complexity (O(n)) so it can skip
ahead when the start handle is not within its service handles.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
It may be very important information for the developer if scanning
fails to start or stop, so add proper logs. There's no need to log
EALREADY errors, since the mesh stack doesn't track the current scan
state and simply relies on the under lying GAP layer to return this
error if the desired state is already set.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
All docs should have a label at the top that would
permit cross-document linking via :ref:`labelname`.
Update "testing" label that would have conflicted and fix the only
reference to the old "testing" label in development process
documentation.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
.object_access.* sections should be with
GROUP_LINK_IN(ROMABLE_REGION) as other sections in
common-rom.ld
Fixes#15481
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
SPI is not normally enabled, but some tests assume that there's a device
available. Conditionally enable SPI_2 which is associated with the
on-board flash.
Closes#15374
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
bt_gatt_connected should be only called, when there is no
connection error. Change fixes problem with receiving notifications
before connection.
Signed-off-by: Marek Pieta <Marek.Pieta@nordicsemi.no>
Add config overlay for cdc_acm+dfu composite configuration.
Manual configuration over menuconfig may be error-prone for
the user because then FLASH_LOAD_OFFSET and FLASH_LOAD_SIZE
should also to be set to appropriate values.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Set bwPollTimeout for DFU_GETSTATUS request dynamically.
For now, adjust bwPollTimeout only during DNLOAD stage.
Fixes: #8734
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Remove 'counter' as a supported feature on several NRF boards as these
boards fail to build tests/drivers/counter/counter_basic_api. This is
due to the fact that we either need explicit board conf files for the
test or have the counter driver enabled via Kconfig.
Fixes#15460
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Exclude nucleo_f302r8 platform as the tests doesn't fit in flash size.
This is due to that fact that we pull in newlib for the STM32 counter
driver.
Fixes#15460
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Clearing the pending IRQs when resetting the timeout fixes the
forward time drifting, but the change needs more investigation
until we are sure this won't break kernel time management.
Reverting the change to get 1.14 release out.
This reverts commit 2895da02a4.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The nxp mpu uses the logical OR of access permissions when multiple
region descriptors apply to a given memory access. This means that we
must partition the sram into two non-overlapping regions to implement
the mpu stack guard. This partitioning gets reconfigured at every
context switch, and if an interrupt occurs during this time, it can
cause a fault because we do not have a valid mpu region descriptor for
the sram.
This scenario was observed on frdm_k64f in tests/posix/common before
commit 2895da02a4, which changed timing.
In this case, we couldn't even print fault information to the console
and the hardware would reset. It looked a lot like a watchdog reset,
unless you attached a debugger to see the fault.
A similar problem was fixed in commit
ec424b7a45, but this change temporarily
disabled the mpu.
Fix both cases by locking interrupts during the critical sections, as
this is more secure than disabling the mpu.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Clean up accumulated release notes with (final) clarity edits, spell
check, and such. Remove "Working Draft" from the heading.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
HFCLK may be requested for multiple modules, i.e. Bluetooth stack.
When any other module has requested HFCLK to run, the driver will
return -EBUSY on free attempt which is not an error - thie means
that free request has been processed, but someone else is still
requiring the clock to run. When all clock users free the clock,
it may be disabled.
Related issue: #15145
Signed-off-by: Paweł Zadrożniak <pawel.zadrozniak@nordicsemi.no>
Added information to release notes about Zephyr modules which allow for
splitting ext/ into multi-repo instead using Zephyr modules.
Signed-off-by: Torsten Rasmussen <torsten.rasmussen@nordicsemi.no>
The macros that generate the handler and implementation functions
changed the generated names. Fix the comments to match.
Signed-off-by: Bradley Bolen <bbolen@lexmark.com>
The i2s_cavs.c driver manipulates cache lines before commencing
any DMA transfers. With write-back cache, if the DMA receive
buffer is not aligned to the cache lines, the data around
the buffer will be invalidated and may never written to memory.
Since the driver takes an external memory slab as buffer and
there is no easy way to force cache line alignment on
the application side, set the cached region to write-through
to avoid potential issue.
Fixes#13223
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
revert commit 3e255e968 which is to adjust stack size
on qemu_x86 platform for coverage test, but break other
platform's CI test.
Fixes: #15379.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Move the doc version selection menu from the bottom of the left nav menu
to above the TOC menu, making it more obvious.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
Drop mode in RTT backend was broken. It is not the default
one so most likely it was unnoticed for a long time. Fixed
to report drop message when logs are lost.
Additionally, added assert to ensure that memmove does not
do memory overwrite.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
This is an old script for finding references to undefined Kconfig
symbols that assumes Kconfiglib 1 (an older API).
There's now a different check for references to undefined symbols (see
commit 1d0834b35f ("checks: kconfig: Check for references to undefined
Kconfig symbols") in the ci-tools repo).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
As part of the ll_reserve refactoring effort, the packet length now
includes header size as well. Before the refactor, when the packet
length was written to the device, it did not include the header size,
which is the required value as per the LM3S6965 datasheet. After the
refactor the packet length includes the header size as well. The
header size has to subtracted from the packet length before writing to
the device. Fixes#13943.
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
