When the connection is terminated, make sure that any pending
data is feed to the application.
Fixes#28057
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
VCO input frequency can be checked and set during compile time.
It unfortunately does not work for output frequency because macros in
HAL are defined together with uint32_t type.
This also fixes wrong check in case of HSI used as PLL source.
Signed-off-by: Jan Pohanka <xhpohanka@gmail.com>
Add the supported features section to serpente.yaml and overlay files
to the corresponding tests and samples.
Signed-off-by: Alexander Falb <fal3xx@gmail.com>
timeslice terminology were used in connection with synchronization
using ll BLE ticker.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Rework ticker synchronization using newly introduced
radio synchronization API.
In kconfig synchronization using ll ticker become choice
option.
If CONFIG_SOC_FLASH_NRF_PARTIAL_ERASE is enabled the erase
timing is changed so intervals become similar to slots duration.
Previously interval was always ~90 ms, which looks like it was kept
so disproportional by oversight while the partial erase was
introduced.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Extract synchronization procedures using LL BLE controller
ticker to newly added synchronization API.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Introduced API which allows to decouple radio synchronization
mechanism from NVMC driver.
New API will allows to replace synchronization mechanism if required.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The _gatt_ infix was determined to be unnecessary as
GATT is implied by it being a Bluetooth service.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The _gatt_ infix was determined to be unnecessary as
GATT is implied by it being a Bluetooth service.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
The _gatt_ infix was determined to be unnecessary as
GATT is implied by it being a Bluetooth service.
Signed-off-by: Emil Gydesen <emil.gydesen@nordicsemi.no>
Add handling of the HCI_Hardware_Error event to log the hardware code.
This event was unmasked in set_event_mask.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Use time(), localtime_r(), and asctime() to confirm that the
declarations required for these (newlib) libc functions are made
available in CONFIG_POSIX context.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Some of what's supposed to be in <time.h> was lost because this header
attempts to define everything using more primitive include files.
Instead incorporate the contents from the toolchain-provided header.
Any gaps should be picked up by the legacy content present in this
file, which should not conflict with the toolchain header.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add a name to the Kconfig choice that selects the controller TX power.
This allows board `*.defconfig` files to change the default TX power
as their certifications warrant. For example:
```
choice BT_CTLR_TX_PWR
default BT_CTLR_TX_PWR_PLUS_4
endchoice
```
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
Identify the special case of /zephyr,user as a node for which property
values are generated without having to define a binding.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Tell the EDT instance that properties of the /zephyr,user node should
be generated based on the binding types inferred from the property
content.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Clean up of devicetree tooling removed generation of information
present in devicetree in nodes that have no compatible, or for extra
properties not defined by a binding. Discussion proposed that these
properties should be allowed, but only in a defined node /zephyr,user.
For that node infer bindings based on the presence of properties.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Preserve the TX power set with the `BT_HCI_OP_VS_WRITE_TX_POWER_LEVEL`
command for advertising and scanning procedures. As the TX power is no
longer overwritten on procedure start, the TX powers can now be set
before starting the procedure. This eliminates the chance for the first
transmissions to use the default TX power instead of the request TX
power.
Similar changes are not made to the connection advertising powers as
changing the TX power for a connection to device A should not change
the TX power for a future connection to device B using the same
`struct lll_adv` instance.
Fixes#27921.
Signed-off-by: Jordan Yates <jordan.yates@data61.csiro.au>
This adds few tests for handling scan response in ext commands:
- trying to set scan response on non-scannable instance should fail
- it should be possible to create scannable instance, set scan data,
enable and then disable set
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
ADI field is optional in AUX_SCAN_RSP so by default it's disabled, but
now we'll have an option to include it.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
When aux is upated, DID is changed and unlike SID it's only stored in
aux PDU. To allow quick access to new DID value, let's just optionally
return current ADI value after aux was updated. It will be useful e.g.
when updating scan response data if we want to put ADI there.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This enables processing of AUX_SCAN_REQ and sending back AUX_SCAN_RSP
on non-connectabe scannable advertising instances. Similar path will
be used for AUX_CONNECT_REQ so there are few references for connectable
as well, but this is not supported as for now.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This adds restrictions for setting scan response data as specified by
Core spec:
* on legacy, only complete data can be set
* on legacy, data cannot be longer than 31 octets
* on ext, if non-scannable, data can only be discarded
* if ext enabled, only complete data can be set
* if ext enabled, data cannot be discarded
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
This allows to set scan response data using ext adv commands.
New AUX_SCAN_RSP can be created without analyzing previous PDU since
the only value that need to be copied from previous PDU is AdvA which
is placed at fixed location. TxPower is omitted since, if enabled, it
is already present in AUX_ADV_IND and does not need to be presed in
other PDUs. ADI support is to be added later.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
AdvA in aux is mandatory for any connectable and scannable set so make
sure it's always added.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Connectable and scannable instances always have aux so we need to force
AuxPtr to be included in primary PDU and have aux allocated even if no
data are set.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Connectable and scannable instances always have AuxPtr so we can return
error immediately if controller is configured with no aux.
Signed-off-by: Andrzej Kaczmarek <andrzej.kaczmarek@codecoup.pl>
Prevent redundant collision resolves and potential incorrect and harmful
increment of lazy_current.
During collision scenarios with high CPU load, the ticker_worker may be
called a second time before the ticker_job gets to run. This will cause
ticker operations on the previosly expired node (expected), and in some
cases increment lazy_current, even though the node was not sceduled to
execute via the req/ack mechanism.
By moving the request check before collision resolve, CPU time is saved,
and lazy_current will not incorrectly be incremented if node is in
collision.
The problem may be seen as a connection suddenly not receiving packets,
or MIC error on master, because the event counter goes out of sync.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Use a helper config BT_CTLR_CONN_RSSI_SUPPORT so that it is only
enabled when supported by the controller.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
add a new testcase to:
Verify some operations of rbree are running in
logarithmic time.
Verify an user defined structure contains rbtree node works.
verify "for each"style APIs work.
Signed-off-by: Ningx Zhao <ningx.zhao@intel.com>
By default, subprocess.Popen commands are supplied as a list of strings.
Using split() allows to use command with arguments, for example it is
possible to use following:
sanitycheck ... \
--device-serial-pty="set_ambient read_terminal.py" \
...
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add tool which can access ADSP console over IPM using Python device
library and polling Doorbell registers.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Add console over Inter Processor Mailboxes (IPM).
This is useful for AMP processors like ADSP found on up_squared board.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
The SX126x supports using DIO2 to control an TX switch, but only if
the switch can be operated using a single control signal. Add support
for RF switches that are wired to a GPIO instead of the radio chip
itself. This makes it possible to use RF switches that require two
control signals (one for the RX port and one for the TX port) by
wiring them to two GPIOs on the MCU.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
This commit extends USB hid API callbacks by adding
'const struct device *dev' parameter. If the application
configured more than one HID device then it must specify
separate hid_ops for each device as its unable to determine
for which device the callback was called.
This patch makes it possible to have only one hid_ops within
the application and the application is aware for which device
the callback was called because of explicit device pointer.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
