How prompts work is better documented nowadays, and these comments might
not be that helpful if you don't know.
There are lots promptless symbols that don't have a comment.
Also fix up some comments in arch/Kconfig that seem misplaced/redundant,
and clean up some whitespace (no blank line after a comment makes it
look like it only applies to the symbol directly after it to me).
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Enable ETHERNET_HW_TX_CHKSUM_OFFLOAD, ETHERNET_HW_RX_CHKSUM_OFFLOAD,
ETHERNET_AUTO_NEGOTIATION_SET and the equivalent driver configuration
in eth_mcux driver.
Autonegoitiation was done at driver initialization.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
It is possible that the network interface is not yet initialized
when status of the PHY changes. In this case we must not call
net_eth_carrier_on() as that will cause a crash.
This was noticed with mimxrt1050_evk board.
Fixes: #21257
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though.
Also replace some
config
prompt "foo"
bool/int
with the more common shorthand
config
bool/int "foo"
See the 'Style recommendations and shorthands' section in
https://docs.zephyrproject.org/latest/guides/kconfig/index.html.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Set the network interface up / down according to link status.
This means that we call Ethernet carrier on/off function in
proper places.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This commit refactors kernel and arch headers to establish a boundary
between private and public interface headers.
The refactoring strategy used in this commit is detailed in the issue
This commit introduces the following major changes:
1. Establish a clear boundary between private and public headers by
removing "kernel/include" and "arch/*/include" from the global
include paths. Ideally, only kernel/ and arch/*/ source files should
reference the headers in these directories. If these headers must be
used by a component, these include paths shall be manually added to
the CMakeLists.txt file of the component. This is intended to
discourage applications from including private kernel and arch
headers either knowingly and unknowingly.
- kernel/include/ (PRIVATE)
This directory contains the private headers that provide private
kernel definitions which should not be visible outside the kernel
and arch source code. All public kernel definitions must be added
to an appropriate header located under include/.
- arch/*/include/ (PRIVATE)
This directory contains the private headers that provide private
architecture-specific definitions which should not be visible
outside the arch and kernel source code. All public architecture-
specific definitions must be added to an appropriate header located
under include/arch/*/.
- include/ AND include/sys/ (PUBLIC)
This directory contains the public headers that provide public
kernel definitions which can be referenced by both kernel and
application code.
- include/arch/*/ (PUBLIC)
This directory contains the public headers that provide public
architecture-specific definitions which can be referenced by both
kernel and application code.
2. Split arch_interface.h into "kernel-to-arch interface" and "public
arch interface" divisions.
- kernel/include/kernel_arch_interface.h
* provides private "kernel-to-arch interface" definition.
* includes arch/*/include/kernel_arch_func.h to ensure that the
interface function implementations are always available.
* includes sys/arch_interface.h so that public arch interface
definitions are automatically included when including this file.
- arch/*/include/kernel_arch_func.h
* provides architecture-specific "kernel-to-arch interface"
implementation.
* only the functions that will be used in kernel and arch source
files are defined here.
- include/sys/arch_interface.h
* provides "public arch interface" definition.
* includes include/arch/arch_inlines.h to ensure that the
architecture-specific public inline interface function
implementations are always available.
- include/arch/arch_inlines.h
* includes architecture-specific arch_inlines.h in
include/arch/*/arch_inline.h.
- include/arch/*/arch_inline.h
* provides architecture-specific "public arch interface" inline
function implementation.
* supersedes include/sys/arch_inline.h.
3. Refactor kernel and the existing architecture implementations.
- Remove circular dependency of kernel and arch headers. The
following general rules should be observed:
* Never include any private headers from public headers
* Never include kernel_internal.h in kernel_arch_data.h
* Always include kernel_arch_data.h from kernel_arch_func.h
* Never include kernel.h from kernel_struct.h either directly or
indirectly. Only add the kernel structures that must be referenced
from public arch headers in this file.
- Relocate syscall_handler.h to include/ so it can be used in the
public code. This is necessary because many user-mode public codes
reference the functions defined in this header.
- Relocate kernel_arch_thread.h to include/arch/*/thread.h. This is
necessary to provide architecture-specific thread definition for
'struct k_thread' in kernel.h.
- Remove any private header dependencies from public headers using
the following methods:
* If dependency is not required, simply omit
* If dependency is required,
- Relocate a portion of the required dependencies from the
private header to an appropriate public header OR
- Relocate the required private header to make it public.
This commit supersedes #20047, addresses #19666, and fixes#3056.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Use this short header style in all Kconfig files:
# <description>
# <copyright>
# <license>
...
Also change all <description>s from
# Kconfig[.extension] - Foo-related options
to just
# Foo-related options
It's clear enough that it's about Kconfig.
The <description> cleanup was done with this command, along with some
manual cleanup (big letter at the start, etc.)
git ls-files '*Kconfig*' | \
xargs sed -i -E '1 s/#\s*Kconfig[\w.-]*\s*-\s*/# /'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Clean up space errors and use a consistent style throughout the Kconfig
files. This makes reading the Kconfig files more distraction-free, helps
with grepping, and encourages the same style getting copied around
everywhere (meaning another pass hopefully won't be needed).
Go for the most common style:
- Indent properties with a single tab, including for choices.
Properties on choices work exactly the same syntactically as
properties on symbols, so not sure how the no-indentation thing
happened.
- Indent help texts with a tab followed by two spaces
- Put a space between 'config' and the symbol name, not a tab. This
also helps when grepping for definitions.
- Do '# A comment' instead of '#A comment'
I tweaked Kconfiglib a bit to find most of the stuff.
Some help texts were reflowed to 79 columns with 'gq' in Vim as well,
though not all, because I was afraid I'd accidentally mess up
formatting.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Re-run with updated script to convert integer literal delay arguments to
k_sleep to use the standard timeout macros.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
The zephyr/subsys/net/l2 include directory has been added through the
'zephyr_library_' API to modify the 'zephyr' library, when the
'zephyr_' API should have been used.
This patch fixes this problem. Using 'zephyr_library_' in this context
works by accident when 'zephyr' is the current library but has no
guarantees of working in the future.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
This patch adds support for configuring the MAC address through the
Network Management API to the STM32 Ethernet driver.
Signed-off-by: Markus Fuchs <markus.fuchs@de.sauter-bc.com>
When randomly generating MAC addresses they will always be
locally administrated addresses, so the LAA bit should be set.
The LAA bit is the 2nd bit of the 1st byte of the MAC address
not the 2nd bit of the 4th byte.
Fixes: #16452
Signed-off-by: Erwin Rol <erwin@erwinrol.com>
This was only used on the Quark SoCs. It is no longer used, can no
longer be tested, and it's reliant upon the deprecated legacy PCI
subsystem. Remove it to prevent bitrot.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This commit adds support for a 6LoCAN Ethernet border translator.
CAN frames with the translator CAN address are translated and forwarded
to Ethernet. Ethernet frames with the first 34 bits matching the MAC
address of the translator are translated and forwarded to 6LoCAN.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
ETH_LITEETH is defined in drivers/ethernet/Kconfig.liteeth, which is
source'd within a menu that has 'depends on ETH_LITEETH', in
drivers/ethernet/Kconfig.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Liteeth exposes two memory regions:
* set of rx/tx buffers (aka slots) to exchange packets,
* control and status registers.
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
For STM32F7 MCU the actual implementation doesn't work when the
DMA buffers are placed in the SRAM.
This might be a problem with caches.
To overcome this problem, the buffer is moved to the DTCM.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
uint8_array values are now generated as structure initializers. Update
the code accordingly. The implementation assumes that existing
devicetree source does not provide the correct OUI so preserves the
in-driver override of the value provided by devicetree and its setting
for random/unique addresses.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
uint8_array values are now generated as structure initializers. Update
the code accordingly. The implementation assumes that existing
devicetree source does not provide the correct OUI so preserves the
in-driver override of the value provided by devicetree.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
move misc/util.h to sys/util.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/printk.h to sys/printk.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move misc/__assert.h to sys/__assert.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move spi.h to drivers/spi.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move i2c.h to drivers/i2c.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move gpio.h to drivers/gpio.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move clock_control.h to drivers/clock_control.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
move sys_io.h to sys/sys_io.h and
create a shim for backward-compatibility.
No functional changes to the headers.
A warning in the shim can be controlled with CONFIG_COMPAT_INCLUDES.
Related to #16539
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Convert DT_.*_GPIO_{CONTROLLER,PIN,FLAGS} ->
DT_.*_GPIOS_{CONTROLLER,PIN,FLAGS)
Used the following commands to make these conversions:
git grep -l DT_.*_GPIO_CONTROLLER | xargs sed -i 's/DT_\(.*\)_GPIO_CONTROLLER/DT_\1_GPIOS_CONTROLLER/g'
git grep -l DT_.*_GPIO_PIN | xargs sed -i 's/DT_\(.*\)_GPIO_PIN/DT_\1_GPIOS_PIN/g'
git grep -l DT_.*_GPIO_FLAGS | xargs sed -i 's/DT_\(.*\)_GPIO_FLAGS/DT_\1_GPIOS_FLAGS/g'
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Found a few annoying typos and figured I better run script and
fix anything it can find, here are the results...
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Change code from using now deprecated DT_<COMPAT>_<INSTANCE>_<PROP>
defines to using DT_INST_<INSTANCE>_<COMPAT>_<PROP>.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This is mainly testing purpose from native_posize ethernet
driver. Enable CONFIG_ETH_NATIVE_POSIX_VLAN_TAG_STRIP to have
VLAN tag strip feature on ethernet Rx frames.
Signed-off-by: Ravi kumar Veeramally <ravikumar.veeramally@linux.intel.com>
Migrate from "legacy" PCI support (drivers/pci) to new PCI(e) support.
The e1000 driver is merely for testing with QEMU and so should not be
a model for the use of PCI(e) functions. Consult instead "real-world"
PCI(e) drivers like the NS16550 UART (drivers/serial/uart_ns16550.c).
Signed-off-by: Charles Youse <charles.youse@intel.com>
As part of the ll_reserve refactoring effort, the packet length now
includes header size as well. Before the refactor, when the packet
length was written to the device, it did not include the header size,
which is the required value as per the LM3S6965 datasheet. After the
refactor the packet length includes the header size as well. The
header size has to subtracted from the packet length before writing to
the device. Fixes#13943.
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
Update the files which contain no license information with the
'Apache-2.0' SPDX license identifier. Many source files in the tree are
missing licensing information, which makes it harder for compliance
tools to determine the correct license.
By default all files without license information are under the default
license of Zephyr, which is Apache version 2.
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Rename reserved function names in drivers/ subdirectory. Update
function macros concatenatenating function names with '##'. As
there is a conflict between the existing gpio_sch_manage_callback()
and _gpio_sch_manage_callback() names, leave the latter unmodified.
Signed-off-by: Patrik Flykt <patrik.flykt@intel.com>
When building with -fno-inline, the compiler complains about
undefined reference to this function. This happens when
building for code coverage. Since this function is only called
within the file, mark it static also.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
In the conversion of net_pkt_read_new to net_pkt_read, we missed
changing the function in the eth_smsc911x and eswifi_offload.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Some places were still using the old allocator. Using the new one does
not change any behavior. This will help to remove the useless data_len
attribute in net_pkt which legacy allocator was still setting.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Remove magic numbers from Ethernet drivers and tests by defining
NET_ETH_MAX_DATAGRAM_SIZE and NET_ETH_MAX_FRAME_SIZE.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Removing the TX timeout handling in the GMAC driver (commit 18b07e09e0)
revealed some issues with the way hardware priority queues work.
For cases with both hardware priority queues enabled, with the default
recommended delta bandwidths (0% - 75%), the lower priority queue (0%)
is hardly able to send any packets. This became visible, because without
the timeout mechanism, we quickly ran out of available TX buffers if
there were multiple packets being queued to the queue.
Here is an excerpt from 802.1Q, chapter 34.3.1 which describes how Qav
bandwidth sharing SHOULD work:
The deltaBandwidth(N) for a given N, plus the deltaBandwidth(N) values
for any higher priority queues (larger values of N) defines the total
percentage of the Port’s bandwidth that can be reserved for that queue
and all higher priority queues. For the highest priority queue, this
means that the maximum value of operIdleSlope(N) is deltaBandwidth(N)%
of portTransmitRate. However, if operIdleSlope(N) is actually less
than this maximum value, any lower priority queue that supports the
credit-based shaper algorithm can make use of the reservable bandwidth
that is unused by the higher priority queue. So, for queue N-1, the
maximum value of (operIdleSlope(N) + operIdleSlope(N-1)) is
(deltaBandwidth(N) + deltaBandwidth(N1))% of portTransmitRate.
However in reality, the lower priority queues (N-1) on the SAM GMAC
hardware DO NOT use the bandwidth available from the higher priority
queues (N).
This commits fixes the issue by changing the defaults. These are still
set to the recommended 75% (total), but this percentage is split between
the priority queues manually.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
There is a log message printed for the non-priority queue (Queue 0). Add
the same message for the priority queues too when they are enabled, and
a corresponding message when the queue is not used (set to idle).
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Throughout the manual, the queues GMAC is equipped with are identified
by a number - Queue 0, Queue 1 and Queue 2.
However in the context of Qav, the queues are identified with a
character (note that there are only two queues as Qav is not used for
the non-priority queue) - Queue A and Queue B.
Queue B and Queue 2 are also called "the highest priority queues".
Based on that, the previous implementation was using the following
mapping:
Queue 1 - Queue A
Queue 2 - Queue B
However when running some specific tests, that is for example forcing
all the traffic to Queue 1, it showed that this queue is actually
affected by the Queue B registers. Similarly, Queue 2 seems to be
affected by the Queue A registers.
Based on that observation, this commit changes the registers used to
work with the following mapping:
Queue 1 - Queue B
Queue 2 - Queue A
Note that this is based solely on observations, there is nothing in the
datasheet that confirms this, and the "highest priority" label suggests
it is otherwise.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This option is meant to be used only for debugging. Use it to force all
traffic to be routed through a specific hardware queue. With this option
enabled it is easier to verify whether the chosen hardware queue
actually works.
This works only if there are four or fewer RX traffic classes enabled as
the SAM GMAC hardware supports screening up to four traffic classes.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The interface name is IFNAMSIZ long so we must not copy it
full which would overwrite the terminating null byte.
Coverity-CID: 195770
Fixes#14419
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Some of these are from 'source'ing a file within a menu that has a
'depends on NET_L2_ETHERNET' (in drivers/ethernet/Kconfig) and then
adding another 'depends on NET_L2_ETHERNET' within it.
Similarly, subsys/net/l2/ethernet/Kconfig sources files within an
'if NET_L2_ETHERNET'.
'if FOO' is just shorthand for adding 'depends on FOO' to each item
within the 'if'. Dependencies on menus work similarly. There are no
"conditional includes" in Kconfig, so 'if FOO' has no special meaning
around a source. Conditional includes wouldn't be possible, because an
if condition could include (directly or indirectly) forward references
to symbols not defined yet.
Tip: When adding a symbol, check its dependencies in the menuconfig
('ninja menuconfig', then / to jump to the symbol). The menuconfig also
shows how the file with the symbol got included, so if you see
duplicated dependencies, it's easy to hunt down where they come from.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Fix calculation of frame length in eth_enc28j60_rx().
The calculation was incorrect because the CRC size was
subtracted only from the lower byte.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
The j iterator is used for priorities, and the i iterator is used for
choosing the actual screening register. Therefore the screening register
availability needs to be checked with i.
This commit also improves the readability by doing two things:
* by moving the screening register index check to a place where the
index is going to be actually used
* by using the ARRAY_SIZE macro instead of a hard-coded number as the
upper limit
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The feature that used this symbol was removed in 18b07e09e0.
This is just a cleanup commit that removes the unused symbol.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
These options were removed from kconfig in previous patch. So rename
the leftovers as shared_irq driver options are defined in DTS now.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Same change as in commit 8cf8db3a73 ("Kconfig: Use a short, consistent
style for prompts"), fixing stuff that got introduced since then.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
In was generating these warnings:
eth_stellaris.c:66:8: warning: unused variable ‘eth_hdr’
eth_stellaris.c:65:8: warning: unused variable ‘head_len_left’
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Wait in the send callback for the packet to be actually sent.
After this change, only one TX packet will be handled at once.
This is needed because of the way the TX packets are currently handled
in L2 after this PR: #12563
This is similar to what #13167 did for the SAM GMAC on SAM E-70.
Without this, packet time-stamping does not work with the current stack.
This commit is minimalistic on purpose to make it easily revertible when
the network stack is able to properly handle DMA drivers for TX packets
again.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The ring_buf implementation is basically used as an array of net_buf
pointers in the RX path. The tail and head indexes are taken from the
RX descriptors and not from the ring_buf. That's why for example the
fact that head is never initialized doesn't cause problem. Only len is
used in free_rx_bufs(), but anyway this function is plainly broken as
it always free the first net_buf and doesn't set it back to NULL.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Scale down the TX path of the GMAC driver by waiting for a packet to be
fully sent before returning from the send function. This has a small
performance impact, but has a few advantages:
- It allows the Ethernet code to modify the packet afterward, fixing PTP
support on this board (see PR #12563).
- It returns an error to the IP stack in case of a transmit failure.
- It doesn't require net_buf to be thread safe.
This change can be reverted by changing GMAC_MULTIPLE_TX_PACKETS from 0
to 1.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The GMAC driver tries to ensure that it can always send a complete
Ethernet frame. However in the TX path this is the problem of the IP
stack: if the buffers can't be allocated, they won't be sent. Therefore
just drop the check.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that the RX packets are limited to the RX workqueue only, we can
reduce ETH_SAM_GMAC_BUF_RX_COUNT to 12 and still be able to receive a
full Ethernet frame. This reduces the minimum NET_BUF_RX_COUNT required
by this driver to 24.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
This reverts commit afbee4c96a. The IP
stack has been fixed and does not use the RX packets or buffers to
transmit data.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Commit 040d6b6e99 (eth: eth_mcux: Convert to use DT_ prefixed defines)
changed all the defines, but to incorrect ones.
This commit changes them to what actually gets generated.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The eth mcux driver has been using non DT_ prefixed defines for DT
generated defines. Switch to use DT_ prefixed ones as we want to
deprecated the non DT_ prefixed defines.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SAM GMAC Ethernet driver currently keeps a reference to the packet
being sent in addition than keeping of references of the fragments. In
practice this is only needed when PTP is enabled, otherwise the driver
only need to prevent the fragment (or even their content) to be changed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SAM GMAC Ethernet driver uses scatter gather DMA to transmit data.
Each fragment of a network packet is mapped from a set of descriptors
that is used by the controller to do the DMA transfer. This means that
the packet is not necessary sent when the send() function returns. For
that reason the driver calls net_pkt_ref() on the packet to prevent it
from being freed. It is then unreferenced with net_pkt_unref() in the
TX ISR when the packet has effectively been sent.
However this doesn't work if the packet is modified in the meantime,
like it will be done in PR #12563 to remove the Ethernet header
contained in the first fragment. To avoid that, call net_pkt_frag_ref()
on each fragment of the packet, and unreferenced them with
net_pkt_frag_unref() in the TX ISR when the packet has effectively been
sent.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Replace the sole use of i2c_burst_read_addr with a more generic API
function to allow the former to be deprecated along with its unreliable
sibling write and update functions.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This allows the shared_irq driver to be configured by device tree.
With previous implementation, only the board configuration can
override the IRQ trigger, as the trigger config is a "choice" rather
than "config". With this patch, the driver can be fully configued at
the SoC level.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Use the new API where relevant. Only sam_gmac is left aside for now.
This simplifies a lot the code as the caller should only care about
allocating net_pkt and its buffer once, and thus will not need to mess
with "frags" etc...
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Force Operation Mode Strap Override register to disable NANDTree. This
is due to some users reporting PHY entering NANDTree.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Boot PHY initialization timeout, caching mechanism fixes and networking
buffer descriptors moved to no cache section. Enabled cache management
in networking driver and manual barriers.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Previous SAM E70 HAL version was patched by commit 4dcfc8706 ("Add
missing interrupt number definitions") to add missing interrupt
definitions for SAM GMAC Priority Queues. This has been fixed in the
latest HAL by using a slightly different name. This patch updates the
driver accordingly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Now that the descriptor lists are in non-cached memory, the helpers are
just accessing the w0 or w1 members of the structure. Just drop them and
access the members directly.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Atmel SAM Ethernet module is using a scatter-gather technique to
exchange data with the Ethernet driver. To communicate the location
of the data buffers the driver sets-up a so called descriptor list. This
is effectively a place in RAM containing a sequence of 32-bit words
representing buffer location and its status.
Currently the cache coherency is handled using cache clean or
invalidate. Unfortunately this strategy only works correctly when the
corresponding data size is a multiple of the cache line. This is not
the case here and might lead to data loss or corruption.
Instead of using cache operations, this patch moves the descriptor
listed to the recently added non-cached memory region, as recommended by
ATMEL. A data synchronisation barrier is still required for writes, as
the non-cached memory is defined with TEX=1, i.e. it is not strongly
ordered. The descriptor lists alignment can be decreased to 4 bytes, as
required by the SAM Ethernet module.
The RX/TX buffer are left unchanged, still managed by cache operations.
Fixes#9812
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The RX buffer accounting list is not a list shared with Ethernet device,
therefore there is no need to run a cache clean operation on it.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The SAM E70 GMAC ethernet driver reference a packet with net_pkt_ref()
when queueing a packet, and unreference it with net_pkt_unref() in the
ISR when it has been fully sent.
The call to net_pkt_ref() is done just after re-enabling the
interruptions, so there is however a small race condition that might
cause the packet to be unreference before being referenced. This is
only theoretical and has not been seen in practice.
Fix that by moving the call to net_pkt_ref() just before re-enabling
the interruptions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The previous commit replaced the net_pkt element ref with an element
atomic_ref. CI tests turned up more places where ref was used directly.
This commit converts them to use the new element.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
For some reason, there was sequence like:
1. Get size of RX packet.
2. Allocate pkt buffer.
3. Check if the size of RX packet is too large, then deallocate pkt
buffer and error out.
Instead, reorder operations to check size before allocating buf.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Adds a new config HAS_MCUX_ENET to constrain which socs can enable the
mcux ethernet driver. This will prevent users from enabling the driver
on socs like kl25z or kw41z which do not have ethernet mac hardware.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
We now generate CS GPIO defines from the DTS that we can utilize. We
needed to slightly update the #defines in the driver from:
DT_MICROCHIP_ENC28J60_0_CS_GPIOS_{PIN,CONTROLLER} to
DT_MICROCHIP_ENC28J60_0_CS_GPIO_{PIN,CONTROLLER}
Fixes#12640
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The SAM E70 Ethernet driver uses scatter gather DMA to transmit data.
Each fragment of a network packet is mapped from a set of descriptors
that is used by the controller to do the DMA transfer. Each descriptor
contain an address and a length/status. The important status bits are
GMAC_TXW1_LASTBUFFER to indicate the last fragment of a packet and
GMAC_TXW1_USED to indicate that a descriptor has been processed by the
controller.
When starting a transmission, the controller start at the descriptor
after the last one that has been processed. If the descriptor is NOT
flagged by GMAC_TXW1_USED, it sends a first packet by sending all the
fragments up to a descriptor flagged with GMAC_TXW1_LASTBUFFER. The
first descriptor of a packet *and only the first descriptor of a packet*
is then modified to flag it with GMAC_TXW1_USED and to provide a status
(mostly related to errors and checksum offloading). It then continues
with the next packet and so on and only stops if the next descriptor
after GMAC_TXW1_LASTBUFFER is flagged with GMAC_TXW1_USED.
Therefore in order for the controller to stop processing descriptors,
the strategy is to flag the next descriptor after the last fragment to
be sent with GMAC_TXW1_USED. When the next packet has to be queued, the
flag can be removed before starting a transmission.
This is what is currently done in the current driver. However there is a
small race condition in the implementation: if packets are queued fast
enough, the controller is still sending the fragment of the previous
packet when the descriptor are written. When writing the first
descriptor, the GMAC_TXW1_USED flag is removed. This is done after
writing the address (with a memory barrier) so that looks safe. However
given that the GMAC_TXW1_USED flag is only added by the controller to
the first descriptor of a packet it means the next descriptor might
have it cleared. In that case the descriptor is processed, and a junk
packet is sent. That also desynchronize eth_tx and tx_complete as one
or more packets than expected are transmitted.
In order to fix that the strategy is slightly changed to initially write
the first descriptor with the GMAC_TXW1_USED flag set. Once all the
descriptors from the packet are written the bit is cleared (after a
memory barrier). Then the transmission can be started safely.
The patch also does a small optimization writing the next descriptor
with only the GMAC_TXW1_USED bit set instead of setting this bit. As
this will be a non-cached area, it's better avoiding a read followed
by a write if not necessary.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
If a pkt has more frags than the number of TX descriptors, we end up in
a deadlock situation, as the whole packet and thus all the frags have to
be mapped in the descriptors at once. That is why the number of
descriptors is defined as CONFIG_NET_BUF_TX_COUNT + 1.
This wrongly assumes that only TX buffers can be used to send data,
however the packets might also come from the RX buffers, like for
example with ICMPv4.
Therefore define the number of descriptors as the maximum of
CONFIG_NET_BUF_RX_COUNT + 1 and CONFIG_NET_BUF_TX_COUNT + 1. This fixes
a deadlock when CONFIG_NET_BUF_TX_COUNT is much smaller than
CONFIG_NET_BUF_RX_COUNT.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
The current SAM E70 Ethernet driver sometimes get stuck if the stack
has to send 2 packets in a row, for example an ack for the just received
data + answer data.
The problem is the following one:
1) The first packet goes through eth_tx, one tx_desc_sem semaphore is
taken, and the tx_timeout_work delayed work is submitted.
2) The second packet also goes through eth_tx, another tx_desc_sem
semaphore is taken, and the tx_timeout_work delayed work is not
started because there is already one already submitted.
3) The first packet has been sent, one tx_desc_sem semaphore is given
and the tx_timeout_work delayed work is cancelled.
4) The second packet has been sent but given the delayed work has
already been cancelled, tx_completed is not called: the tx_desc_sem
semaphore is not given back and the network packet is not
unreferenced.
The whole timeout concept probably has to be reworked. In the meantime
it is probably better to just drop the timeout code instead of keeping
the driver broken. We can only get stuck on the TX path if there is a
bug in the driver or a hardware malfunction. It might happen, but with
the less probability then the current hangs. In addition it just hides
the real issues and prevent them to be fixed.
This commit therefore just remove the timeout code in the TX path.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
It was reported, and confirmed by multiple parties that default
CONFIG_ETH_MCUX_RX_BUFFERS=2 under some packet load leads to
1s and increasing packet processing delay and eventual deadlock.
No reports were about CONFIG_ETH_MCUX_TX_BUFFERS=2, but be on safe
side and just set that to the minimal value as the current default,
to allow us to have good conservative base to test various networking
stack issues.
Fixes: #3132
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
As emulated by QEMU. SMSC9118 is compatible with SMSC9220 as used in
ARM MPS2 board, as well as SMSC9115/6/7/etc. devices.
Portions of the code are based on mbedOS code from its
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.c
eth_smsc9220_priv.h originally comes from Arm mbedOS file:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/drivers/smsc9220_eth.h
augmented with struct & defines from:
targets/TARGET_ARM_SSG/TARGET_CM3DS_MPS2/device/CM3DS.h
and renamed as eth_smsc911x_priv.h to follow Zephyr conventions.
Then, following changes applied:
Changes to build under Zephyr, changes to use symbolic constants
and field access helpers, typo fixes, etc.
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
Driver for networking device Microchip ENC28J60 is used as SPI slave,
moved to DTS type definition. Samples echo_client and echo_server use
this device on Arduino 101 board.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
When used suitable config overlay, qemu_cortex_m3 with Ethernet
support can be started with just usual "make run".
An example of such overlay is included with samples/net/echo_server,
can be built and run with:
make BOARD=qemu_cortex_m3 \
CONF_FILE="prj.conf overlay-qemu_cortex_m3_eth.conf" run
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
The Kconfig option ETH_SAM_GMAC was missing it's dependency on
NET_L2_ETHERNET. Before this patch Kconfig was allowing users to
enable the driver, but the driver was not added because the CMake code
only adds the driver when NET_L2_ETHERNET.
Signed-off-by: Sebastian Bøe <sebastian.boe@nordicsemi.no>
There is no need to reserve any space for each frag, as the l2 will
allocate a frag for the ethernet header, arp will do the same.
This is one step further to removing the concept of ll reserve.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
We were reading gPTP header from wrong position when parsing
it in RX and TX.
Fixes#11827
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Check clock_control_on return value now that it is checking appropriate
bus is used in the request.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update such statistic on all drivers.
Also, remove TX stats in native and stellaris drivers: such update is
done in L2 now.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
It's now either L2 which unref the pkt on successful tx, or net_if on
error.
Also removing pkt->frags check, net_core.c:net_send_data() does it
already.
And using data_len in logging instead of net_pkt_get_len(), which one is
currently greedy (it goes over all net_bufs).
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
L2 is the one who requests the packet to be sent, and not via net_if API
anymore. Stellaris driver was merged right after this behaviour change
and was thus lacking the proper modification.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
The driver can be tested using different networking emulation
approaches.
This approach will work across multiple Qemu instances. There can be
more than one Qemu instance, run using the following command. They
would appear to be on the same Ethernet network.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net socket,mcast=230.0.0.1:1234 \
-kernel zephyr.elf
This approach will work with other virtualization technologies that
support connecting to a VDE switch, like VirtualBox and User Mode
Linux. The switch can be started using the following command.
$ vde_switch --sock /tmp/switch
Qemu can be connected to the switch using the following command.
$ qemu-system-arm -M lm3s6965evb \
-serial stdio \
-net nic \
-net vde,sock=/tmp/switch \
-kernel zephyr.elf
Signed-off-by: Fadhel Habeeb <fadhel@zilogic.com>
Signed-off-by: Nirav Parmar <niravparmar@zilogic.com>
Signed-off-by: Vijay Kumar B <vijaykumar@zilogic.com>
If gPTP is enabled, then enable also PTP clock driver so that
gPTP sync starts to work properly for native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
The PTP driver was init too late which prevented gPTP from
working in native_posix board.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
If compiling with gPTP support for native_posix board, then avoid
compile error that is seen with gptp sample application.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Now instead of such path:
net_if_send_data -> L2's send -> net_if tx_queue -> net_if_tx -> driver
net_if's send
It will be:
net_if_send_data -> net_if tx_queue -> net_if_tx -> L2's send -> driver
net_if's send
Only Ethernet is adapted, but 15.4 and bt will follow up.
All Ethernet drivers are made compatible with that new scheme also.
Signed-off-by: Tomasz Bursztyka <tomasz.bursztyka@linux.intel.com>
Enables Networking hardware on i.MX-RT type drivers.
Reuses the same eth_mcux driver used by Kinetis family; initialization
sequence refactored to work with this board as well. Unlike Kinetis
family, i.MX has a single ENET interrupt and we need to discriminate
between interrupts using a status register.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
These changes were obtained by running a script created by
Ulf Magnusson <Ulf.Magnusson@nordicsemi.no> for the following
specification:
1. Read the contents of all dts_fixup.h files in Zephyr
2. Check the left-hand side of the #define macros (i.e. the X in
#define X Y)
3. Check if that name is also the name of a Kconfig option
3.a If it is, then do nothing
3.b If it is not, then replace CONFIG_ with DT_ or add DT_ if it
has neither of these two prefixes
4. Replace the use of the changed #define in the code itself
(.c, .h, .ld)
Additionally, some tweaks had to be added to this script to catch some
of the macros used in the code in a parameterized form, e.g.:
- CONFIG_GPIO_STM32_GPIO##__SUFFIX##_BASE_ADDRESS
- CONFIG_UART_##idx##_TX_PIN
- I2C_SBCON_##_num##_BASE_ADDR
and to prevent adding DT_ prefix to the following symbols:
- FLASH_START
- FLASH_SIZE
- SRAM_START
- SRAM_SIZE
- _ROM_ADDR
- _ROM_SIZE
- _RAM_ADDR
- _RAM_SIZE
which are surprisingly also defined in some dts_fixup.h files.
Finally, some manual corrections had to be done as well:
- name##_IRQ -> DT_##name##_IRQ in uart_stm32.c
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
The error check was wrong, if we could send the packet then
we free it. If sending fails, then let the caller to decide
what to do with the packet.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add "Multicast Promiscuous Enabled" (RCTL_MPE) bit definition and
use it for the receive control register (RCTL) initialization.
Multicast needs to be enabled in order for IPv6 auto-configuration
to succeed.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
The initial sequence was wrong and led to the missing interrupt
problem with netdev backends where the incoming traffic
appears immediately (tap).
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Introduce new Kconfig option for selecting either slip or ethernet
connectivity to host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Change the default behaviour of the host network interface
setup. Now user needs to execute net-setup.sh script from
net-tools project to setup host ethernet interface. The script
needs to be run as a root user. Then zephyr.exe can be started
as a normal user.
Example:
cd net-tools
sudo ./net-setup.sh
This will create zeth network interface and set IP address and
routes properly. See other command line options by typing
./net-setup.sh --help
Old behaviour is still there if one enables
CONFIG_ETH_NATIVE_POSIX_STARTUP_AUTOMATIC=y
in which case one needs to use the command
sudo --preserve-env zephyr.exe
to start the Zephyr process.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Partially replaces Kinetis MCUX driver configuration from Kconfig to
Device Tree. Interrputs moved from defines configuration to DT.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
This patch adds a driver for Intel PRO/1000 Gigabit Ethernet controller.
The driver currently supports only a single instance of the NIC.
Signed-off-by: Oleg Zhurakivskyy <oleg.zhurakivskyy@intel.com>
Adding spaces around "=" when definining Kconfig template so
that is more consistent with overall style of these template
variables.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Starting with glibc 2.20, there is warning when _BSD_SOURCE is defined
but not _DEFAULT_SOURCE (in /usr/include/features.h around line 184).
Sanitycheck turns this warning into error. So define _DEFAULT_SOURCE
at build time for native.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Fix 2 compile issues in RedHat/CentOS 7 for the native
ethernet driver due to a oldish glibc, which does not include
by default the needed structures.
+
Separate the native ethernet driver into its own library,
and set NO_POSIX_CHEATS for it, in case the Zephyr POSIX
library would eventually add support for any of the host functions
used in this driver.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
Calculate proper initial PTP clock divisors based on the MCK value.
Additionally do not allow adjusting the rate of the clock. This does not
seem to work properly with current gPTP rate adjustment algorithm.
Having proper PTP clock divisors and callbacks that allow getting,
setting and adjusting current time is sufficient for proper gPTP
support.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Any word started with underscore followed by and uppercase letter or a
second underscore is a reserved word according with C99.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
The return of memset is never checked. This patch explicitly ignore
the return to avoid MISRA-C violations.
The only directory excluded directory was ext/* since it contains
only imported code.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
After read first packet and if ERDPT < ERXRDPT,cause read Rx FIFO error.
The fix is to set ERDPT properly before reading next packet.
Fixed#9537
Signed-off-by: Frank Li <lgl88911@163.com>
The eth_stm32_hal has been tested to work correctly on Nucleo-F207ZG,
Nucleo-F429ZI, Nucleo-F746ZG and Nucleo-F767ZI.
Signed-off-by: Daniel Egger <daniel@eggers-club.de>
Consistently use
config FOO
bool/int/hex/string "Prompt text"
instead of
config FOO
bool/int/hex/string
prompt "Prompt text"
(...and a bunch of other variations that e.g. swapped the order of the
type and the 'prompt', or put other properties between them).
The shorthand is fully equivalent to using 'prompt'. It saves lines and
avoids tricking people into thinking there is some semantic difference.
Most of the grunt work was done by a modified version of
https://unix.stackexchange.com/questions/26284/how-can-i-use-sed-to-replace-a-multi-line-string/26290#26290, but some
of the rarer variations had to be converted manually.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
Up until now, Zephyr has patched Kconfig to use the last 'default' with
a satisfied condition, instead of the first one. I'm not sure why the
patch was added (it predates Kconfiglib), but I suspect it's related to
Kconfig.defconfig files.
There are at least three problems with the patch:
1. It's inconsistent with how Kconfig works in other projects, which
might confuse newcomers.
2. Due to oversights, earlier 'range' properties are still preferred,
as well as earlier 'default' properties on choices.
In addition to being inconsistent, this makes it impossible to
override 'range' properties and choice 'default' properties if the
base definition of the symbol/choice already has 'range'/'default'
properties.
I've seen errors caused by the inconsistency, and I suspect there
are more.
3. A fork of Kconfiglib that adds the patch needs to be maintained.
Get rid of the patch and go back to standard Kconfig behavior, as
follows:
1. Include the Kconfig.defconfig files first instead of last in
Kconfig.zephyr.
2. Include boards/Kconfig and arch/<arch>/Kconfig first instead of
last in arch/Kconfig.
3. Include arch/<arch>/soc/*/Kconfig first instead of last in
arch/<arch>/Kconfig.
4. Swap a few other 'source's to preserve behavior for some scattered
symbols with multiple definitions.
Swap 'source's in some no-op cases too, where it might match the
intent.
5. Reverse the defaults on symbol definitions that have more than one
default.
Skip defaults that are mutually exclusive, e.g. where each default
has an 'if <some board>' condition. They are already safe.
6. Remove the prefer-later-defaults patch from Kconfiglib.
Testing was done with a Python script that lists all Kconfig
symbols/choices with multiple defaults, along with a whitelist of fixed
symbols. The script also verifies that there are no "unreachable"
defaults hidden by defaults without conditions
As an additional test, zephyr/.config was generated before and after the
change for several samples and checked to be identical (after sorting).
This commit includes some default-related cleanups as well:
- Simplify some symbol definitions, e.g. where a default has 'if FOO'
when the symbol already has 'depends on FOO'.
- Remove some redundant 'default ""' for string symbols. This is the
implicit default.
Piggyback fixes for swapped ranges on BT_L2CAP_RX_MTU and
BT_L2CAP_TX_MTU (caused by confusing inconsistency).
Piggyback some fixes for style nits too, e.g. unindented help texts.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
User can take the zeth interface down by issuing "net iface down <idx>"
shell command. It is possible to take the interface up by typing
"net iface up <idx>" in shell. These commands are important for
native_posix as there is no physical cable that can be connected
or disconnected.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Most of this code is unreachable with priority queues disabled because
of queue id validation.
Fixes#9295.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Allow user to configure a program that is executed after the
network interface is created and IP address is setup.
This can be used e.g., to start wireshark to capture
the network traffic of the interface.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This is a finishing commit in 802.1Qav support for SAM GMAC. It adds a
possibility to get and set all parameters required by the standard.
Note that to be fully compliant it requires a proper system
configuration, but the prioritizing mechanisms will work just fine
without it so it is not enforced in any way.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
If the application is using TC configuration compatible with HW
configuration (equal number of traffic classes and hardware queues)
setup the screening registers and chose queues based on the chosen TC
mapping.
Use the VLAN priority and hard-coded mappings only as a fallback.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Updating Qav params made it implicitly enable the Qav support itself.
Since we can now control the on/off status with a management request,
this is not a desired behavior.
Make it read the original register value before updating params and then
writing back what it was before.
Additionally we now have to explicitly enable Qav support in init.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The standard (and therefore the upper layer) is using bits per second,
the registers in SAM GMAC uses bytes per second - do the conversion
before writing the reg.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
unistd.h was missing (used by read, close..)
printk header was also missing, but replace it's use
with posix_print_trace: It is faster and does not require
any Zephyr functionality to work.
fflush is not needed in this case.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
The native_posix random driver uses random() and srandom()
whicha are old XOPEN POSIX extension (part of POSIX 2001).
To avoid compiler warnings due to the host libC headers
not including this prototypes otherwise, let's define
this 2 macros.
Signed-off-by: Alberto Escolar Piedras <alpi@oticon.com>
- Remove redundant 'n' defaults. 'n' is the default value for bool
symbols.
This makes the auto-generated documentation clearer as well: You get
"implicitly defaults to n" instead of
"- n if <propagated dependencies>".
- Shorten
<type>
prompt "foo"
to
<type> "foo"
This works for all types, not just bool.
- Various formatting nits.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
There are too many individual requests for Qav related parameters. There
are more Qav parameters that need to be supported (and will be supported
soon - both on the GET and SET side). Handling it the way it was handled
so far would render the eth mgmt API dominated by Qav parameters. That
would make the file hard to read and understand.
Instead of that - use a single GET and SET requests for all Qav
parameters. This works by adding a separate enum with Qav request type
to the ethernet_qav_param struct.
Additionally this approach makes it much easier to document it all since
we now have just a single request and documentation comments in the
ethernet_qav_param struct.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This commit makes the driver enable HW Qav support for all available
priority queues.
Note that the hardware doesn't support setting the deltaBandwidth
parameter directly, but it is possible to do this by calculating it
from the negotiated link speed.
The default settings are set according to 802.1Qav 34.3.1, that says:
The recommended default value of deltaBandwidth(N) for the highest
numbered traffic class supported is 75%, and for any lower
numbered traffic classes, the recommended default value is 0%.
The default/recommended values can be changed using the ethernet
management API (set_config) - which this commit also adds.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Handle getting the number of priority queues. The total number of queues
for this driver is configured in kconfig so it is as simple as returning
a defined value in this case.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
Follow the packet sending error code in the driver. If packet
cannot be sent, then return <0 to the caller and do not free
the packet. In practice this is not happening here but follow
this general rule anyway.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Use both PTP Peer Event and PTP Event timestamping registers when
necessary.
Also for non-PTP frames just use current time.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This commit adds support for multiple hardware TX and RX queues.
The number of the queues to use can be configured through defconfig.
Packets are sent and received through different hardware queues
depending on their priority.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This commit fixes how the registers values are calculated and makes sure
there is no overflow effect when converting back to int.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This commit makes the driver disallow drastic clock rate changes.
These changes happen mostly in the very beginning, when the timestamp in
hardware is zeroed.
In such cases the set callback is called soon after and fixes the large
offset. Without this limit the clock offset oscillates for a longer
period before it properly syncs as the requested ratio jumps between
very large and very small values.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This commit fixes a memory leak happening when both gPTP and VLAN are
enabled.
It also moves the get_iface function up in the file so it is accessible
earlier without a redundant function declaration.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This adds packet timestamping support to the GMAC driver.
It is based on the eth_native_posix and eth_mcux drivers.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The pointers to pkt->frags->data are changed after transmitting.
Other layers (e.g. the gPTP drivers) assume that these will remain
unchanged. This patch adds a workaround for that issue and restores the
original pointers.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The advantage to this approach allows drivers for
devices that already keep statistics data on hardware
registers to use those instead, rather than try to
replicate it the same counters again within the driver
itself.
The eth_native_posix.c driver though do not benefit
from this, is modified to use the new callback system.
Suggested-by: Jukka Rissanen <jukka.rissanen@intel.com>
Signed-off-by: Jonathan Yong <jonathan.yong@intel.com>
If VLAN is enabled for specific PTP interface, then manipulate
the ethernet header properly in this case.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
This adds packet timestammping support to the driver and configures
various PTP options in ENET.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Signed-off-by: Julien Chevrier <julien.chevrier@intel.com>
Allow gPTP code to be run as a linux process and communicate
with gPTP daemon running in linux host.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Bool symbols implicitly default to 'n'.
A 'default n' can make sense e.g. in a Kconfig.defconfig file, if you
want to override a 'default y' on the base definition of the symbol. It
isn't used like that on any of these symbols though, and is
inconsistent.
This will make the auto-generated Kconfig documentation have "No
defaults. Implicitly defaults to n." as well, which is clearer than
'default n if ...'
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
The previous default, CONFIG_ETH_MCUX_0_RANDOM_MAC, result in a random
MAC address changed each reboot. As reboots happen quite often during
development, while Ethernet peers usually cache existing MAC addresses
in ARP cache, this led to situation when a board after reboot didn't
respond to pings or any other connection attempts for random amount of
time (upo to 10-20s). This was quite confusing and looked like some
problem in driver/hardware/connection/whatever.
Instead, introduce new option, CONFIG_ETH_MCUX_0_UNIQUE_MAC, to make
MAC address from MCU unique identification register. This results in
randomized/unique MAC address which is also stable over reboots and
avoids the situation described above.
Fixes: #3187
Signed-off-by: Paul Sokolovsky <paul.sokolovsky@linaro.org>
This is needed to avoid compilation warnings when using both the
built-in libc and newlib.
The warnings were caused by typedefs incompatibilities.
This was agreed to be the temporary solution at the TSC.
See #8469 for more details.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
The subsys/net/ directory is more logical place for L2 code instead
of ip/ directory. No functionality changes by this commit.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Attempts to clear/invalidate caches which are disabled lead to BUS
FAULTS.
Ensure they are enabled before using them.
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
What needs to be done for the cache to work properly:
* Make sure cache operations are aligned to 32B
* Make sure to clean and invalidate the operations on gmac descriptors
(thus all the helper functions)
This commit is needed for SAM GMAC to work when caches are enabled and
MPU mapping is changed to cacheable (See #8185)
Signed-off-by: Tomasz Gorochowik <tgorochowik@antmicro.com>
This makes it easier to distinguish them from "true" undefined symbols.
Internally, all int/hex literals are treated as undefined symbols, which
always get their name as their value. The C tools work the same way.
The plan is to turn references to undefined Kconfig symbols into an
error later.
Signed-off-by: Ulf Magnusson <Ulf.Magnusson@nordicsemi.no>
If carrier is ON or OFF, then tell this information to upper IP stack
so that it can act accordingly.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Don't hard code the syslog level to DEBUG, instead use the
CONFIG_SYS_LOG_ETHERNET_LEVEL setting like other ethernet drivers.
Signed-off-by: Michael Scott <michael@opensourcefoundries.com>
Native POSIX echo server sends malformed response to echo request of
size larger than 128 bytes (default size of each network data
fragment). Wireshark notices that by tagging echo request with "No
response seen". This commit fixes that issue.
Signed-off-by: Ruslan Mstoi <ruslan.mstoi@intel.com>
Convert couple of MSEC() calls to K_MSEC() as the timeouts
when using MSEC() are just too long.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
