On stm32mp157c_dk2, the pin mapped on arduino connector pin A3
could not be used as GPIO.
As a consequence, pin "irq-gpio" from x_nucleo_iks01a3 shield
should not be used.
Use board overlay to remove it from shield definition.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Add support for the BuyDisplay 3.5" TFT + touch shield based on ILI9488
controller and FT6236 touch.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Make driver generic for multiple ILI displays. The adopted strategy is
to share all driver code except register initialization, which has been
found to have some specific registers/values depending on the
controller.
The driver has been adjusted to support multiple compatibles.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Move the data/command GPIO from Arduino header 16 (D10), which collides
with Arduino SPI SS, to Arduino header 15 (D9).
Add commented example for specifying a reset GPIO on Arduino header 14
(D8).
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Add Inventek es-WIFI modules shield. This shield exposes es-WIFI driver
using Arduino Uno R3 header by UART or SPI interfaces. It shows how
user can create their own overlay and expose es-WIFI driver.
The current Inventek's EVB doesn't have all pins necessary to control
the module by Arduino hearder. This shows how to wire to get ISM43xx
EVB working.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
This change allows to use SSD1306 based displays to be used on the
SPI bus as well.
Adding SPI shield.
Tested on SSD1306 and SSD1309 based displays using I2C.
Tested on SSD1309 based display using SPI.
Signed-off-by: Marco Peter <marco@peter-net.ch>
Move pixel format setting (RGB565/RGB888) to DeviceTree. Add support for
changing pixel format at runtime.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Add support for the ARM DesignStart DAPLink board for Digilent Arty
S7/A7 (V2C DAPLink) shield.
This shield is designed to be used along with the ARM Cortex-M1/M3
DesignStart FPGA reference designs running on the Digilent Arty.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Align all Kconfig option names with LVGL names. The followed rule:
LV_(.*) -> CONFIG_LVGL_(.*).
Also replaced LVGL boolean configuration entries using if/else/endif
with direct IS_ENABLED macro.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Removes redundancy on atmel_rf2xx.overlay message. Clarifies supported
variations section and notes about network on index.rst.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Add note about the availability of touch panel IRQ linei when a jumper
in the board is soldered. A Device Tree commented entry has also been
added to ease testing it.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Because the H1 heading was not set in mikroe_eth_click index.rst
file, the shields listing page was listing H2 headings for this
shield.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
Add devicetree overlay for connecting an Mikroe ETH click shield to an
NXP LPCXpresso55S69 development board.
The LPCXpresso55S69 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ETH click board definition assumes SPI CS0.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Replaces .conf type configuration with .defconfig.
Makes configuration conditional, it depends on shield definition and
networking.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
The current shield version shows different configuration, including
disabling default ethernet and wifi interfaces. To allow easy
connection from standard headers, this add two new shield designations.
The existing boards overlays and defconfig were updated.
The documentation was update to reflect changes. A new supported
variations section helps to understand what shield variation user need
select to build their own system.
This changes requires changes on esp32 offload tests to reflect new
esp_8266 shield designations. Sam4e_xpro was keeped as the only one
with dedicated overlay and both frdm_k64f and disco_l475_iot1 were
moved to use standard arduino r3 header using extra args.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The Atmel RF2xx module shield is a generic solution to enable any Atmel
AT86RF2xx IEEE 802.15.4 transceiver. This module enables IEEE 802.15.4
RF2xx Zephyr driver.
The Atmel RF2xx module shield enables any board with an Atmel Xplained,
Xplained-Pro, Arduino or MikroBus expansion header to connect to
networks operation with IEEE 802.15.4, OpenThread or any other stack
based on this media type.
The Atmel RF2xx module is configured to allow interoperate with other
medias like Ethernet. User need configure network stack properlly.
Fixes#26259.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The generic SPI GPIO chip select support now respects devicetree flags
for signal active level. Update all cs-gpios properties to specify
active low.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Since commit 5963ebaf33
("drivers: spi: CS configuration through devicetree")
the SPI GPIO CS flags are obtained from DT,
but the patch series has missed the necessary changes
in the device trees for displays and link_board_eth.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Add devicetree overlay for connecting an Mikroe ADC click shield to an
NXP LPCXpresso55S16 development board.
The LPCXpresso55S16 uses SSEL1 (CS1) for mikroBUS SPI, whereas the
generic Mikroe ADC click board definition assumes SPI CS0.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Use the recently introduced mikrobus_spi devicetree node as parent node
instead of relying on mapping for arduino_spi.
Signed-off-by: Henrik Brix Andersen <henrik@brixandersen.dk>
Fixes whitespace in the frdm_kw41z shield document to allow continuation
in the numbered list of Bluetooth controller instructions and to format
the jumper configuration sublist correctly.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Appropriate WS can be loaded automatically if
the display controller has integrated temperature
sensor or an external sensor is connected.
Signed-off-by: Johann Fischer <j.fischer@phytec.de>
Removed flow control configuration from Kconfig and updated samples
to use device tree for that.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
Adds support for a new SHIELD, Eth Click.
Mikro-BUS type shield supported in Zephyr.
Adds Kconfig for mikroe_eth_click shield.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Use DT_INST_SPI_DEV_HAS_CS_GPIOS() in drivers to determine if we should
utilize CS_GPIO base SPI chipselect handling. This allows us to remove
Kconfig option for this feature.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
As we phase out per instance Kconfig symbols convert to utilize
DT_DRV_INST to initialize CAN instances.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Fix node status to "okay" instead of "ok" which doesn't
seem to be in used anymore across the tree.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
x-nucleo-iks02a1 shield is an arduino compatible companion board
which can be used on top of Nucleo standard boards for industrial
applications. It extends the Nucleo functionalities adding following
MEMS sensor support:
- ISM330DHCX 3-axis accelerometer and 3-axis gyroscope
- IIS2MDC 3-axis magnetometer
- IIS2DLPC 3-axis accelerometer
- IMP34DT05 digital microphone.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Add ESP-8266 modules shield. The ESP-01 needs to be loaded with
ESP8266 AT Bin V1.6.2 which is compatible with ESP8266 AT Bin
V1.7.x which is the minimal supported version by ESP WIFI driver.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
Convert CAN to use a chosen node property that is similar to how we
handle zephyr,entroy or zephyr,flash-controller as the means to select a
specific peripheral instance utilized by a subsystem.
Replace references of the form:
alias {
can-primary = &can1;
};
with:
chosen {
zephyr,can-primary = &can1;
};
Replace various macro/define references with either
DT_CHOSEN(zephyr_can_primary) or replace DT_ALIAS_CAN_PRIMARY_LABEL
with DT_CHOSEN_ZEPHYR_CAN_PRIMARY_LABEL.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
