The spi_nrfx_spis driver uses nodelabel so we need to use
DEVICE_DT_DEFINE instead of DEVICE_DT_INST_DEFINE.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The K_MSEC macro evaluates its argument twice, which causes double
evaluation of some function calls in the mesh stack.
This removes all instances of function calls inside K_MSEC macros in the
mesh stack.
Signed-off-by: Trond Einar Snekvik <Trond.Einar.Snekvik@nordicsemi.no>
With kernel page table isolation (KPTI) we cannot use right exception
stack since after using trampoline stack there was always switch to
7th IST stack (__x86_tss64_t_ist7_OFFSET). Make this configurable as a
parameter in EXCEPT(nr, ist) and EXCEPT_CODE(nr, ist). For the NMI we
would use ist6 (_nmi_stack).
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
NMI can be triggered at any time, even when in the process of
switching stacks. Use special stack for it.
Signed-off-by: Andrei Emeltchenko <andrei.emeltchenko@intel.com>
Convert adc drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
DEVICE_GET -> DEVICE_DT_GET
DEVICE_DECLARE -> DEVICE_DT_INST_DECLARE
etc..
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allow Kconfig to override default values of Kconfig symbols
defined in modules' Kconfig files. For that, the .defonfig
files need to be source'd before the modules' Kconfig files.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
The fix_elf_addrs script runs objcopy over a binary that (due to some
legacy section definitions in a mildly complicated linker file) has a
few zero-length sections at address zero. Objcopy considers this a
warning condition (though oddly the linker from the same version of
binutils which produced that binary does not!), which will be detected
as a CI failure.
Just eat the warnings. Long term we should rework linkage to remove
the legacy stuff that is getting tripped over.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
It is really bad when you start having doubts about those edge cases
in your sleep. Better have it validated here instead.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
Add enum for LE Read Transmit Power phy values, which are different
form the values used for PHY update procedure since it includes values
for the LE Coded PHY coding schemes.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Added a new Bluetooth API that can be used to read the current and
maximum transmit power level of the radio. The reading operation is
performed over HCI.
Signed-off-by: Kamil Piszczek <Kamil.Piszczek@nordicsemi.no>
Previously, if the peer address was not set, the host would
do undirected advertising even if the application applied
options only applicable to directed advertising.
Adding this additional parameter validation reduces the confusion
of application developers when they have configured something wrong.
Signed-off-by: Rubin Gerritsen <rubin.gerritsen@nordicsemi.no>
Convert pwm drivers to use new DT variants of the DEVICE APIs.
DEVICE_AND_API_INIT -> DEVICE_DT_DEFINE
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
`POLL_TIMEOUT_MAX` should use `CONFIG_BT_MESH_LPN_POLL_TIMEOUT`
instead of `CONFIG_BT_MESH_LPN_INIT_POLL_TIMEOUT`. The described
algorithm to grow the poll timeout implemented in function
poll_timeout does not work with this implementation.
It's a regression in 3b4d58a
Bluetooth: Mesh: optimize performance for lpn node
Fixes: #30338
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Add weak function to check flash configuration.
On stm32g4: single bank configuration not supported
when dual bank capable.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Remove hardcode bank1 page limit (128) which is not always valid
(not valid for soc stm32g474rct)
Manage bank1/2 discontinuity when flash is Dualbank and
flash size is lower than 512K.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
When flash is Dualbank and flash size is lower than 512K,
then there is a discontinuity between bank1 and bank2.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Release the CUI/CPR lock if the connection owning the lock is
terminated.
This can happen if a device performing a CUI/CPR procedure gets a LSTO
before the procedeure completes or the procedure itself TO.
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
`app_key_del` first param should be key_app_idx,
not key_net_idx.
The effect is that app_key_del is broken.
It's a regression in eca014115
Bluetooth: Mesh: Isolate cryptographic material
Fixes: 30468
Signed-off-by: Lingao Meng <menglingao@xiaomi.com>
Add option to enable software CSMA backoff in the OpenThread MAC layer.
This allows to run CSMA procedure correctly in radios that do not
support hardware CSMA backoff, and use them as RCP, where this feature
is required.
Signed-off-by: Robert Lubos <robert.lubos@nordicsemi.no>
In order to release irq_offload semaphore outside kernel/thread.c, we
make it visible by modifying it non-static under ztest. This would be
needed such as when call irq_offload() to enter interrupt context and
a fatal error happened, then you have to release it in your fatal
handler, or the irq_offload will still be locked and no longer be
using again.
Signed-off-by: Enjia Mai <enjiax.mai@intel.com>
range_map() now doesn't implicitly hold x86_mmu_lock, allowing
callers to use it if the lock is already held.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Add a serie of helpers to extract power management states from device
tree. DT_PM_STATE_ITEMS_LIST generates a list of a pm_state and
DT_PM_STATE_INFO_ITEMS_LIST a list of pm_state_info.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Test macro DT_PROP_BY_PHANDLE_IDX_OR. There are two tests, one when
the property exists and other when the property is not set.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Add power state property binding and include this property in cpu.
The pm-state attribute is a enum that matches with enum pm_state right
now the only timing attribute is the minimum residency that is the
minimum time for a power state be worthwhile.
Signed-off-by: Flavio Ceolin <flavio.ceolin@intel.com>
Rework the runner to improve various issues.
Every board.cmake file for an nRF SoC target is repeating boilerplate
needed for the nrfjprog runner's --nrf-family argument. The
information we need to decide the --nrf-family is already available in
Kconfig, so just get it from there instead. Keep the --nrf-family
argument around for compatibility, though.
This cuts boilerplate burden for board maintainers.
We also need to revisit how this runner handles recovery to fix it
in nRF53 and keep things consistent everywhere else.
To cleanly handle additional readback protection features in nRF53,
add a --recover option that does an 'nrfjprog --recover' before
flashing. Keep the behavior consistent across SoCs by supporting it on
those too. Because this is expected to be a bit tricky for users to
understand, check if a --recover is needed if the 'nrfjprog --program'
fails because of protection, and tell the user how to fix it.
Finally, instead of performing a separate 'nrfjprog --eraseall', just
give --chiperase to 'nrfjprog --program' process's arguments instead
of --sectorerase. This is cleaner, resulting in fewer subprocesses and
avoiding an extra chip reset.
Having a separate 'west flash --recover' option doubles the number of
test cases if we want to keep exhaustively enumerating them. That
doesn't feel worthwhile, so update the test cases by picking a
representative subset of the possibilities. Each test now has enough
state that it's worth wrapping it up in a named tuple for readability.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
This commit adds a missing otPlatSettingsDeinit function
to the Zephyr OpenThread platform implementation.
Signed-off-by: Rafał Kuźnia <rafal.kuznia@nordicsemi.no>
