We've never propertly generated any pinmux info, so remove generation
from the binding yaml files for pinmux properties.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
stm32wb55rg is a dual core SoC (M4/M0) with a radio/protocol stack
running on M0 core. M0 FW starts at flash address 0x80CB000.
So flash size available to zephyr is 812K instead of 1M.
Configure package size to reflect this (flash size is now 812K)
and update MPU setting to exclude M0 FW. From MPU point of view,
we set flash size to 512K since we should chose a size being a power
of 2.
If we consider there will be 2 images partitions in a FOTA scheme,
512 K is beyond image-0 and hence is sufficient to cover application
image.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
sram2a and sram2b where defined in the prospect of defining
HCI shared memory sections from device tree.
Remove them, since this is not the case anymore.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Since Kconfig is responsible for enabling/disabling devices at build,
the devices in dt are defaulted to status="ok" to keep the output in
generated_dts_board.conf the same across configurations and simplify
the board-level dts files.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
This adds support for the async API for SAM0 SERCOM USARTs using
DMA to drive the device.
Tested on SAMD21 with a few trivial programs and with
tests/drivers/uart/uart_async_api.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
This adds support for the basic timer counter (TC) found on SAM0
series parts. This driver only supports running the counter
in 32 bit wide mode. Since this mode explicitly slaves the odd
counters to the even ones, only instances of the even ones are
defined.
Tested with tests/drivers/counter/counter_basic_api on SAMD21.
Signed-off-by: Derek Hageman <hageman@inthat.cloud>
Add support for the Low Power Inter-Integrated Circuit (LPI2C)
controllers found in the NXP Kinetis KE1xF SoC series.
Signed-off-by: Henrik Brix Andersen <hebad@vestas.com>
The node name for device_id was device_id@0 it should be
device_id@80a00c to reflect the first register region
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
import linux-v5.1:Documentation/devicetree/bindings/vendor-prefixes.txt
Use vendor-prefixes.txt to check vendor prefixes
used in compatible strings and property names.
Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Previous the register size was 1M, technically the there are only a
small handful of registers defined in the IOAPIC, so shrinking the size
to 4k, so its as most one page large.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The IOAPIC node shouldn't have been in the cpu container, especially
since the cpu container does:
#address-cells = <1>;
#size-cells = <0>;
So the reg field of the IOAPIC would be treated as 2 registers instead
of a register and size. Move IOAPIC node out of the CPU node fixes this
issue.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
The Apollo Lake devicetree is augmented with its 8 I2C interfaces.
The default number of dynamic IRQ stubs is increased to deal with
these new interfaces having IRQ vector detection at runtime.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The legacy PCI support in the DesignWare I2C driver is replaced with
the new PCIe support. The Intel Quark X1000 SoC and the galileo board
configurations are updated accordingly.
Signed-off-by: Charles E. Youse <charles.youse@intel.com>
The SARA-R4 series modules from U-Blox are size-optimized LTE-M /
NB-IoT and EGPRS modules designed for low power consumption and
longer battery life.
The binding identifies the UART device, power GPIO and reset GPIO
lines.
Signed-off-by: Michael Scott <mike@foundries.io>
The label binding was missed during initial development of the
WNC-M14A2A modem. Let's add the binding so that during the
migration to a shield, we can update the DTS correctly.
Signed-off-by: Michael Scott <mike@foundries.io>
ARM SysTick peripheral is optional in Cortex-M0 MCUs,
so we delete the respective dts node when the peripheral
is not present.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Atmel SAM D series SoC variants (present in the tree) all have
an ARM Cortex-M0+ core, not a Cortex-M0, so we correct this in
the .dtsi header.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Unlike Cortex-M3 and Cortex-M4, in Cortex-M7 the number of
MPU regions may vary based on the implementation. This commit
adds a DTS node for the ARM MPU peripheral in the device tree
of Cortex-M7 SoCs and updates the fixup files, so we may extract
the number of MPU regions at build time. SoCs:
- nxp_rt
- same70
- stm32f7
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds a DTS node for the ARM MPU peripheral in the
device tree of ARMv8-M SoCs (for the secure and the non-secure
DTS descriptions) and updates the fixup files. SoCs:
- nrf9160
- musca_a
- musca_b1
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add DTS binding files for the ARM MPU, for both ARM
MPU architecture variants, ARMv7-M and ARMv8-M.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add enum to list what values of maximum-speed are exceptable since
enum's get represented as strings in DT. This also allows us to
generate a code enum to correspond to the string.
We also introduce include/dt-bindings/usb/usb.h which is a hand coded
definition of the enum. We don't have a great way to generate this
right now, however it would be better if we did.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
MHU (Message Handling Unit) enables software to raise interrupts to
the processor cores. It is enabled in SSE 200 subsystems.
This patch aims to implement inter processor communication.
Signed-off-by: Karl Zhang <karl.zhang@linaro.org>
Add LiteX with softcore CPU VexRiscV SoC definitions and default
configurations.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX interrupt controller driver and bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX timer driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Add LiteX UART driver with bindings for this device.
Signed-off-by: Filip Kokosinski <fkokosinski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Adding missing erase-block-size entries for the flash-controller
nodes in the nrf52810 and nrf52811 .dtsi files.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Move flash-controller and SRAM node definitions under SoC node.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Reduced Kconfig for counter with nRF TIMER and RTC. Added overlays
for TIMER and RTC configuration in the counter test.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
