There is possibility that endrx interrupt will be triggered in the
middle of timer interrupt responsible for UARTE timeout, this
patch handles this case.
Signed-off-by: Mieszko Mierunski <mieszko.mierunski@nordicsemi.no>
Commit 16d8ce519c introduced changes
that caused this sample to no longer behave according to documentation
and for some hardware to no longer work at all.
On nRF51 SoCs for instance, the reported number of cycles per second
is 16M, what makes the calculated max_period and min_period to be 16
and 0 microseconds, respectively, what effectively makes it impossible
for the sample to return to the initial blinking frequency. Moreover,
with such short PWM periods, the blinking is not even noticeable.
This patch partially reverts the changes mentioned above, and instead
of calculating max_period and min_period basing on the reported clock
rate, it tries to only decrease the max_period if needed, accordingly
to what the used hardware can handle.
Documentation is also updated to mention the possible change in
observed behavior of the sample on some hardware.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
LSM303AGR is a special one in terms of raw value scale among all devices
supported by lis2dh.c driver. Apply proper scale factor based on
sensitivity scale provided in LIS2DH and LSM303AGR datasheets.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Add new bindings for already supported (by lis2dh.c driver) lsm303agr
accelerometer. Using st,lsm303agr-accel compatible will allow in
subsequent commit to apply different sensitivity scale.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All values were scaled by 8 instead of 12 for 16g compile-time selected
range. This resulted with values around 6.5 m/s^2. Scaling for runtime
configurable ranges was broken for all except 2g range option due to
totally broken lis2dh_range_to_reg_val().
Fix wrong scaling for 16g compile-time and all runtime selectable ranges
by reworking code that scales raw value. While doing this, change
lis2dh->scale type from 16 to 32 bits. This allows to slightly increase
final result precision by using the fact that raw values have maximum 12
bits precision, allowing us to multiply lis2dh->scale by (1 << 4)
compared to previous implementation.
Fix bug #19872.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
According to struct sensor_value documentation, val2 should be negative
for negative result. So drop code that tries to make val2 positive.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
In settings write NVS errors were not handled
in a few places.
This patch improve that.
fixes#20515
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
As presented to the TSC, Zephyr's out-of-box experience for new
developers is, well, complicated. A number of suggestions were
presented including simplifying the getting started material to present
a straight-forward path through the setup and installation steps through
to getting a sample application built, flashed, and running.
This PR is a work-in-progress towards addressing this OOB experience
with a minimal-distractions version of the GSG. Alternatives, warnings,
and material that could lead the developer astray were moved to
alternative/advanced instruction documents (based on the previous
separate Linux/macOS/Windows setup guides) and a new "Beyond the GSG"
document.
We do take advantage of a sphinx-tabs extension for synchronized tabs to
present OS-specific instructions: clicking on one tab will display all
same-named tabs throughout the doc.
We hope (and will continue evaluating) that this new GSG gets developers
set up quickly and then we can send them along to other documents to
continue learning about Zephyr and trying other sample apps.
Thanks for all your previous feedback that I've worked
into this new version.
Signed-off-by: David B. Kinder <david.b.kinder@intel.com>
in SMP, arc uses gfrc as wall clock, so it's ok
to enable SYSTEM_CLOCK_SLOPPY to avoid unnecessary
interrupts
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* fix the smp timer dirver bugs found in debug and test.
for smp case, GFRC is used as clock source, and local
internal timer is used to trigger time event.
* because 64-bits gfrc is used, so idle can be igored as no kernel
tick will be missed
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
It's found that in nsim_hs_smp, sometimes the cpu
doesn't response inter-core interrupt after executing sleep
instruction.
It may be a bug of nsim, but needs more time to
investigate the root of this issue.
This commit is a workround for this, as nsim is just an
instruction simulator, no direct impact.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
* necessary fixes after commit 11bd67db where ipi interrupt is used
to notify other cores to do a thread switch if necessary
* then for arc, it's needed to ignore swap_ok and check whether thread
switch is needed in the exit of irq handling.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Explicitly configures the rgb led pinmuxes as gpios. Currently the gpio
driver quietly changes the pinmux to gpio mode when configuring a gpio
pin, but this behavior is about to change.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Some board description files failed to note where gpio was supported,
causing tests to be inappropriately filtered. Add the feature where
the gpio_basic_api test would use it.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Add device tree elements for all gpio ports of the efr32mg12p including
the dts fixup entries.
Also remove gpio port e since this is not available in efr32mg12p socs.
Signed-off-by: Christian Taedcke <hacking@taedcke.com>
SoC initialization had an incorrect comment regarding system clock.
Corrected from 48Mhz -> 96Mhz.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
NXP's LPC family of MCU's GPIOs parameters is udated.
Boards LPC54xxx and LPC55xxx have updated values according
pin and interrupt layout.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Up to now interrupts could be only configured once, with no way to
disable them in runtime.
Allow interrupts to be disabled in runtime and then properly reenabled
on user request. This allows to ignore interrupts when software is not
expecting them.
The improvement over previously reverted patch [1] is that we disable
interrupts only when we configure port for which interrupt line was
previously selected. This for example prevents to disable interrupts
line 2 in case PA2 was previously configured as interrupt source, but we
are currently configuring PB2 as output.
[1] 0951ce2d34 ("gpio: stm32: support disabling and reenabling
interrupts on pin")
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This patch doesn't change functionality, but is only related to improved
readability and reusability.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
With dual core handling introduction, we now need to take care to
always release lock before exiting function.
Rework gpio_stm32_config to take this into account.
Additionally, since ENOSYS usage is resevred to system calls
handling, replace with EIO.
Signed-off-by: Erwan Gouriou <erwan.gouriou@linaro.org>
Update Zephyr manifest so it picks the tip of hal_nordic.
Signed-off-by: Bartosz Sokolski <bartosz.sokolski@nordicsemi.no>
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
This commit adds support for bluetooth in nRF52833 SoC.
Bluetooth radio related files created and added to Zephyr.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Name convention for nordic USB driver changed
Kconfig files for custom boards have to be udapted accordingly.
Changes affect only name convention change.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
By adding new SoC to Zephyr drivers has to be updated.
Commit affects:
- USB driver
- support for nRF52833 added.
- support for USB_DEVICE_REMOTE_WAKEUP in hid-mouse added.
- SPI
- IEEE 802.15.4
- CLOCK CONTROL
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit adds support for nRF52833 development board.
Changes afffects:
- Introduce files related to board description.
- Add blank documentation file (for future update).
- configuration files for build process.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This commit adds basic support for nRF52833 SoC.
Changes affect introducing:
- architecuture files (dtsi)
- configuration of nrfx drivers
- adaptation of inclusions based on chosen SoC
- configuration of NFCT_PINS_AS_GPIOS depends on HAS_HW_NRF_NFCT.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This adds support for Zephyr SDK 0.11.* is based on the 0.10 support
with the following changes:
Handle how xtensa toolchains for given targets are organized in SDK
0.11.x. They have their own directories per specific xtensa SoC.
The x86_64 toolchain in the SDK has been updated to build for 32-bit
targets (as it has 32-bit soft float libraries). Use this toolchain for
all x86 builds.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This patch introduces the support of the Low Power Timer
for the STM32WBxx from STMicroelectronics.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This commit enables CAN support for the Olimexino STM32 board.
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Signed-off-by: Alexander Wachter <alexander.wachter@student.tugraz.at>
Provide a clear description of the how the binding maps nexus parent
pin indexes to header pin locations. Also use the standard name "Uno"
when identifying the header physical layout, contrasted with Mega/Due
which is a different physical layout.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
This commit relocates the QEMU-specific code that currently resides in
ProjectBuilder.run to QEMUHandler.handle, in order to align with what
other handlers are doing.
For more details, refer to the PR #20573.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
The current QEMUHandler implementation in sanitycheck does not check
for the process exit code and reports "PASS" even when either the QEMU
executable cannot be launched or exited immediately due to an error
(e.g. unsupported machine type, missing file, ...).
This commit adds QEMU process exit code check and error reporting when
the exit code is a non-zero value.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
