The driver was using CONFIG_SRAM_BASE_ADDRESS as the value used to
recognize whether source buffer is in RAM. This label provide the
base address of the image SRAM, and not the base of actual HW SRAM.
This patch uses nrfx_is_in_ram() instead.
fixes#29467
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Made sram0 visible for NETWORK core target. The core might
access sram0 as shared region might be defined inside it.
Made sram1 visible for APPLICATION core target for keeping
consistence.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
The sample is currently to tied to nrf9160dk_nrf9160 board. Refact to
allow build with board and select between device power management on or
off. Move nrf9160dk_nrf9160.overlay to proper boards directory and add
nrf9160dk_nrf9160.conf to set the correct device. Device PM needs SYS
PM be implemented and is an specific configuration and for those boards
that have it implemented user can add overlay-pm.conf to enable the
feature.
Fixes#28094.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
The at45 and nor spi flash drivers needs flash layout to work.
Probably tested were conducted with SoC that already selects
the FLASH_HAS_PAGE_LAYOUT for internal flash drivers. This add
the missing dependency.
Fixes#28094.
Signed-off-by: Gerson Fernando Budke <nandojve@gmail.com>
I keep seeing people miss the --context option in the "west flash
--help" output.
This option is very important for understanding the runner-specific
options and state, and missing it means people get confused about what
west flash, debug, etc. can do and are doing.
Try to avoid this problem by adding a big fat banner about the
omission of runner-specific options in the main help output, and
provide more hints about how to use --context.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Fix typos, inconsistent naming and formatting issues.
Also setting CONFIG_NFCT_PINS_AS_GPIOS=y because NFC is not used.
Signed-off-by: Martin Jäger <martin@libre.solar>
Tests that include floating-point format specifications may need
cbprintf FP support. Make sure it's available.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Samples that include floating-point format specifications may need
cbprintf FP support. Make sure it's available.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
This module needs to format floating point values in shell print
statements, which requires FP format support.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Introduced two per instance booleans, which get set using DT info:
1. is_lsm303agr_dev: if the device is a LSM303AGR_ACCEL, then
the scale values have to be changed.
2. Handle disconnect-sdo-sa0-pull-up if present in ntsnace DT.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Handle interrupts correctly for multi instance, checking per
device DT bindings instead of global Kconfig definitions.
The old interrupt behaviour has been maintained, fixing DRDY to
be on INT1 and Any Motion event on INT2.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
LIS3DH and LIS2DH12 devices share the same driver with
LIS2DH device. So, the bindings are reusing the same
common structure (as LSM30AGR-ACCEL and LSM303DLHC-ACCEL
devices are already doing)
Signed-off-by: Armando Visconti <armando.visconti@st.com>
So far data that went to stderr was simply dropped in case of minimal
libc. In case of newlib stderr was treated same like stdout
(e.g. fprintf(stderr, ...) was equivalent to fprintf(stdout, ...).
Extend filter on stream pointer to allow both stdout and stderr to pass
data to stdout hook (which is Zephyr console backend in most cases).
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This section was being put in the wrong region, and was in L1-cached
incoherent memory. That's wrong, as users are expected to expressly
ask for "__incoherent" memory and do manual cache management if
required. Default memory of all types should be uncached and
coherent.
Very few spots use this and cache effects tend to be ephemeral, so it
was somewhat obscure. It was discovered via an SMP race when using
logging very close to system start where the log thread on the second
CPU will race with messages added on the first -- log messages are
stored in a __noinit mem_slab.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
This platform had separate backends for the log subsystem and printk
handler, which was silly. Unify them to use the same backend so they
don't clobber each other.
This patch appears to be a lot of lines, but it's really mostly code
motion and renaming.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
In architectures supporting more than 8 WL entries, e.g. pure
software implementations, it is desirable to be able to increase the
WL size. This change increases the range to 1..16 for SOCs other than
nRF5x and OpenISA.
Signed-off-by: Morten Priess <mtpr@oticon.com>
Fix sanitycheck failures when building
samples/bluetooth/peripheral_hr for rv32m1_vega_ri5cy
platform.
Updates from nRF platform related to 255 byte AD data
support have been directly copied into openisa port to
fix build failures.
Relates to commit c2fc629dd2 ("Bluetooth: controller:
255 byte AD payload support").
Fixes#29967.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Document the security changed callback can be called with no change
in the security level when the encryption key has been changed
in the link-layer.
Also update the documentation for set security function to include
the bond information so that it matches the documentation for security
changed callback.
Update pairing process to pairing procedure for consistency.
Signed-off-by: Joakim Andersson <joakim.andersson@nordicsemi.no>
Allow vendor specific increase of user operation capacity for
THREAD, to support queuing additional ticker operations.
Relocate TICKER_USER_<XXX>_VENDOR_OPS to before TICKER_USER_<XXX>_OPS.
Signed-off-by: Thomas Ebert Hansen <thoh@oticon.com>
Removes peripheral aliases from the OpenISA RV32M1 SoC, which are no
longer being used after converting their associated drivers to use
DT_INST macros.
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
Removes peripheral aliases from all NXP SoCs (Kinetis, LPC, and i.MX),
which are no longer being used after converting their associated drivers
to use DT_INST macros. The watchdog alias remains because it is used by
tests/drivers/watchdog/wdt_basic_api/
Signed-off-by: Maureen Helm <maureen.helm@nxp.com>
ZLP - zero length packet is used to indicate that the device
has no more data to send. If the Host asks for more data that the
device can provide and the data size is mutliplication of Endpoint
wMaxPacketSize then the device must terminate the data transfer
with ZLP.
Until this patch Nordic device driver controller was not aware of
the requested data length and could not determine when the ZLP was
required.
This patch introduces a fix that prevents the driver from starting
setup stage before the ZLP is being send.
For consistance with the Zephyr USB stack sending ZLP must be
issued from the stack level. Making trans_zlp flag true results
in blocking the driver from starting setup stage without required
ZLP.
After the data transfer finishes the driver will be prepared for ZLP
and will call back the stack to start writing ZLP. After the ZLP
is being send the driver will automatically start status stage and
end the Control Transfer.
This patch also removes CONFIG_USB_DEVICE_DISABLE_ZLP_EPIN_HANDLING
and aligns Nordic driver with others.
Without this patch the issue could occur when handling get requests.
Typical case is string descriptor of length equal to wMaxPacketSize.
Hosts usually asks for wLength = 255 Bytes when string descriptors
are being requested. In that case to successfully finish the data
stage of the Control transfer the device must send wMacPacketSize
Bytes of actual string descriptor and then ZLP to indicate that no
more data are present. After ZLP the status stage may start and the
request is finished successfully.
Without this patch the driver will not send ZLP making it unable
to end the Control Request successful - this may lead to failing
'Device Descriptor Test' from USB3CV test tool.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This patch adds setup packet copy in the Nordic device
controller driver (ubs_dc_nrfx.c). This patch is required
for subsequent patch that fixes isssues with ZLP handling.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
IN Endpoints does not require to have initialized internal
buffer. The data send are not copied to the internal buffer
anymore. This patch reduces memory usage for IN Endpoints.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
Nordic device driver controller (usb_dc_nrfx.c) was fragmenting
IN transfers longer than wMaxPacketSize long using its
internal buffers. Buffers were reserved for each endpoint.
Because the Low level driver (nrfx) is capable of handling
fragmentation, there is no need to do it at the driver
controller level. Data pointer is used directly to create
the nrfx transfer. Endpoint buffers are not required anymore
and could be dropped.
This patch removes fragmentation of in transfers and omits
usage of internal endpoint buffers. Buffer could be later
freed by subsequent patches.
Nordic low level usbd driver is also capable of adding ZLP
if required however for consistance with the Zephyr USB device
stack ZLP must be triggered from stack level.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
The WS2812 SPI driver needs the pixel data to be clocked out on time,
with no gaps between SPI frames. This makes the nordic,nrf-spi
compatible unsuitable for use, since the corresponding driver doesn't
use EasyDMA to clock out the tx buffers.
Force the arduino_spi node in the DT to SPIM mode by setting its
compatible to nordic,nrf-spim. On nRF52832, this driver is disabled by
default due to Product Anomaly Notice (PAN) 58.
We happen to not be affected by PAN 58 in this instance, because we
never read data over the SPIM, only write it. So it's safe to enable
the SPIM driver. This requires a board-specific Kconfig fragment for
nRF52-DK to enable CONFIG_SOC_NRF52832_ALLOW_SPIM_DESPITE_PAN_58.
Fixes: #29877
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
Add STP transport support for MIPI SyS-T with Kconfig MIPI_SYST_STP,
this is following SyS-T spec Section 7.
And with Kconfig MIPI_SYST_RAW_DATA, add raw data output support for
MIPI SyS-T protocol stack.
Signed-off-by: Wentong Wu <wentong.wu@intel.com>
Add TFM_PROFILE and TFM_ISOLATION_LEVEL options. Options are used to set
up custom board configurations, i.e. LPC55S69 uses medium_profile to fit
TFM images in a small flash area.
Signed-off-by: Andrei Gansari <andrei.gansari@nxp.com>
Cleanup comments: # Provisional entry, subject to approval
That's because the MAINTAINERS file was reviewed in the
last TSC F2F and the entries are not provisional any more.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add help text in some newly introduced and un-documented
TF-M Kconfig options: REGRESSION and IPC.
Signed-off-by: Ioannis Glaropoulos <Ioannis.Glaropoulos@nordicsemi.no>
Add Kconfig options that will be used by the module
to call the function with the desired parameters.
Refactor the tfm_integration samples and
the supported boards.
Update west.yml to bring in Cmake changes that use the new KConfigs.
Signed-off-by: Øyvind Rønningstad <oyvind.ronningstad@nordicsemi.no>
Fix regression in connection radio event close in central
role introduced in commit 222dca5598Fixes#29957.
Signed-off-by: Vinayak Kariappa Chettimada <vich@nordicsemi.no>
Module was using flash driver implementation API call
`page_layout()` which is part driver implementation
interface API.
This patch re-implement this part of code using
`flash_page_foreach()` public API function.
Signed-off-by: Andrzej Puzdrowski <andrzej.puzdrowski@nordicsemi.no>
Although flags with pointers are not defined behavior, there is a
desire to have them work, so add a test and fix the complete
implementation so it passes.
Signed-off-by: Peter Bigot <peter.bigot@nordicsemi.no>
Simplify the code to increase readability, and fix right-padding
for %p.
Also, the compiled code is smaller with those changes applied.
Signed-off-by: Nicolas Pitre <npitre@baylibre.com>
An event was not handled by the clock control resulting in assert
and lack of notification about clock readiness.
Signed-off-by: Krzysztof Chruscinski <krzysztof.chruscinski@nordicsemi.no>
When running sanitycheck without any platform filters (-p option), we
take the default platforms and run on those only. When the -G options is
used for integration testing, the platforms listed as integration
platforms are not being added on top of default platforms.
This change adds integration platforms to the list an treats
integration_platforms as a positive filter, so that
integration_platforms are always being considered.
Fixes#29829
Signed-off-by: Anas Nashif <anas.nashif@intel.com>
Add a way to run dumb_http_server_mt sample application against
HTTP get script (using curl) running in Docker.
Signed-off-by: Jukka Rissanen <jukka.rissanen@linux.intel.com>
