Add uart bus interface to extended esWIFI driver. This enables all
Inventek modules with IWIN AT Commands firmware.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
The WIFI_ESWIFI_NAME config would be uselful when there is no device
tree alternative. The esWIFI driver already is on device tree and the
label property exists. This remove WIFI_ESWIFI_NAME Kconfig variable
and switch to device tree equivalent.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
Remove global access to structure eswifi_spi_data variable. Instead,
add a method to pass access to that structure. This allows better
control to the data bus variable.
Signed-off-by: Gerson Fernando Budke <gerson.budke@atl-electronics.com>
This is a temporary workaround for an issue in TI's RF Driver
API. A subsequent release of the SimpleLink SDK will mitigate
the need for it and it can be reverted when hal/ti receives
that update.
Fixes#29418
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
This change reworks the cc13xx_cc26xx IEEE 802.15.4 driver to use
the TI RF driver API that is available in modules/hal/ti.
There are a number of benefits to using TI's API including
- a stable multi-OS vendor library and API
- API compatibility with the rest of the SimpleLink SDK and SoC family
- potential multi-protocol & multi-client radio operation
(e.g. both 15.4 and BLE)
- coexistence support with other chipsets via gpio
- vetted TI RF driver resources, such as
- the radio command queue
- highly tuned / coupled RTC & RAT (RAdio Timer) API
Fixes#26312
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
In case of h/w setup with multiples device instances it is possible
that some of them wants to use triggers but not the others (no
interrupt line.
Since Kconfig configuration is the same way for all the instances
(CONFIG_LSM6DSL_TRIGGER=y), the driver behaves differently according
to how the device instance has been configured in the DT.
If irq-gpios is present, then the driver initialize the interrupt
part, else it skip irq init and returns ok, but data->gpio != NULL
xis checked in trigger_set() API.
Signed-off-by: Armando Visconti <armando.visconti@st.com>
Enable ARR preload so that period or pulse updates are taken
into account synchronously with update event
(at the end of a ongoing period)
And thus avoid undetermined intermediate pulse.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
Add support for configuring Ethernet pins using DT pinctrl entries. Note
that F1 series pinctrl support is not handled as the driver does not
support F1.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Channels 4..7 are multiplexed on adc16. The NXP HAL exposes
ADC16_SetChannelMuxMode but this function is not yet included
in Zephy. The following patch adds channel-mux-b to the dts
enabling the use of the alternate channels of 16 bit adc.
Signed-off-by: Andreas Dröscher <github@anticat.ch>
1. Merged the single/multiple ring(s) APIs, now these APIs
can handle both which requires passing a ring id.
2. Updated timestamp handling to match the new timestamp
implementation in the SDK driver.
Signed-off-by: Mahesh Mahadevan <mahesh.mahadevan@nxp.com>
Those devices can use several I2C address in order to address more
than 256 Bytes using 8bit addressing. Also several physical component
can be used as a contiguous memory.
Signed-off-by: Guillaume Lager <guillaume.lager@gmail.com>
This patch makes the initialization of workqueue earlier
for Nordic driver. Without this change Nordic devices
will fail tests/subsys/usb/device test as it is resetting
USB and by that will try to start already started workqueue
thread. This may lead to Zephyr fatal error.
Signed-off-by: Emil Obalski <emil.obalski@nordicsemi.no>
This driver supports the PWM driven LEDs. The devices are created from
the DT nodes with a compatible property matching "pwm-leds". For each
child node a LED is created and its "pwms" phandle's node is used to
retrieve the PWM configuration: channel, period and flags. If some of
this properties are missing (it is the case for some PWM controllers),
then reasonable default values are used.
This driver implements the following LED API methods:
- led_on
- led_off
- led_blink
- led_set_brightness
Signed-off-by: Simon Guinot <simon.guinot@seagate.com>
With STM32Cube updates
https://github.com/zephyrproject-rtos/hal_stm32/pull/75
'..._hal_rcc.c' and '..._hal_rcc_ex.c' are now systematically
compiled, due to more and more dependencies from HAL IP on rcc.
So USE_STM32_HAL_RCC and USE_STM32_HAL_RCC_EX becomes useless.
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
This provides structure for the regulator device hierarchy and a
driver for GPIO-controlled regulators along with its binding.
Signed-off-by: Peter A. Bigot <pab@pabigot.com>
At present this driver only supports SPI. Refactor it so that SPI is
just one of the options. This does not change any functionality.
Signed-off-by: Simon Glass <sjg@chromium.org>
This member holds the SPI bus pointer. Change its name to make that
more obvious and so that it can be used for an I2C bus also.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present there are three separate read functions and two write
functions. This makes it harder to provide an interface that can work
with either SPI or I2C.
Use bmi160_read() for all reads and create a new bmi160_write()
function for all writes.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this driver only supports a single instance. It sets up some
of its config in the init routine. It is better to put config in
constant data so that multiple instances can be supported and RAM space
is minimised.
Update the driver accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Currently a 'bmi160' pointer is used to point to the driver data. This
confusing, as the driver uses both data and config. Rename the variable
to 'data' like the bme280 driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
This driver uses verbose names for the config and data structures, which
makes it harder to see which one we are talking about. Shorten it, like
the bme280 driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
All net_bufs allocated to modem_cmd_handler's data->rx_buf are consumed
synchronously in ublox-sara-r4.c in the same thread. This means that
allocating them with timeout makes no sense, because timeout
will *always* be hit when there are no more buffers in net_buf_pool.
Get rid of the unnecessary timeout, as it doesn't help and just slows
down processing of incoming data, increasing possibility of data
overrun.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All net_bufs allocated to modem_cmd_handler's data->rx_buf are consumed
synchronously in gsm_ppp.c in the same thread. This means that
allocating them with timeout makes no sense, because timeout
will *always* be hit when there are no more buffers in net_buf_pool.
Get rid of the unnecessary timeout, as it doesn't help and just slows
down processing of incoming data, increasing possibility of data
overrun.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
All net_bufs allocated to modem_cmd_handler's data->rx_buf are consumed
synchronously in esp.c in the same thread. This means that allocating
them with timeout makes no sense, because timeout will *always* be hit
when there are no more buffers in net_buf_pool.
Get rid of the unnecessary timeout, as it doesn't help and just slows
down processing of incoming data, increasing possibility of data
overrun.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
So far a dedicated buffer was used for data read from modem
interface. New net_bufs were allocated and filled later, which means
that data was lost when no more net_bufs were available in the pool.
Prevent data loss by allocating net_buf before attempting any read on
modem interface. Process incoming data in a loop as long as reading from
interface results in new data. Also remove dedicated buffer
(data->read_buf) and directly fill net_buf content instead. As a side
effect there are less memory copy operations and RAM usage is reduced.
Pre-allocated net_buf is now always appended to data->rx_buf. When there
was no (more) data read from interface to such net_buf, then this empty
net_buf will be on the end of data->rx_buf fragment list. Update
skipcrlf() and findcrlf() implementations to explicitly check for each
net_buf length, instead of blindly assuming them to have at least single
byte.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
cmd_handler_process() does two major things:
- reads data from modem interface and fills data->rx_buf,
- processes data in data->rx_buf.
Split implementation accordingly to two separate functions, which
improves readability (less automatic variables to follow at once) and
simplifies refactoring of each action.
No functional change was intended in this commit.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
This is to make the gpio-i2c initialization occur after the GPIO pin
clock initialization.
Signed-off-by: Cassini Zhuang <cassini.zhuang@hansonggroup.com>
z_tick_get returns signed int. Adapt comparision
statement for remaining time computation.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
If CONFIG_MODEM_SIM_NUMBERS is 'n' than the data_imei field of struct
modem_context doesn't exist, so add ifdef protection for that case.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Allows the use of pin interrupt and callbacks for pca95xx family
GPIO expander chips with an interrupt line.
Enable config flag and define a gpio pin for the expander interrupt-
line (INT) in devicetree and the driver will accept pin interrupt
configurations for the expander gpio pins.
Level triggering is supported through emulation.
A worker is used to avoid waiting for I2C in ISR.
Example devicetree node:
gpioext0: tca9539@77 {
compatible = "nxp,pca95xx";
label = "GPIO_EXT_0";
reg = <0x77>;
interrupt-gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
gpio-controller;
#gpio-cells = <2>;
ngpios = <16>;
};
Fixes: #27561
Signed-off-by: Bent Ove Stinessen <bent@norbit.no>
This removes a semaphore unlock in init_spi function
which causes risks of competitive access
Signed-off-by: Clotilde Sattler <clotilde.sattler@stimio.fr>
Align register names with the ones found in the datasheet. It is easier
to follow datasheet if names are the same.
Some other minor enhancements have also been introduced (comments, use
BIT for bit fields...).
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
The initial configuration provided for the nrfx_power driver cannot
contain just default values, as that mean that DC/DC converters are
to be disabled, while those converters may be (and they actually are
by default for many boards) enabled through Kconfig.
Signed-off-by: Andrzej Głąbek <andrzej.glabek@nordicsemi.no>
Add support for interrupt driven MSI-X PVM feature for Viper.
Function mask bit update is tracked with snoop interrupt
and vector mask bit update is tracked with pcie pmon lite
address range access detection interrupt.
Both the interrupts are required to enable this feature.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
drivers: pcie_ep: iproc: move msi/msix functions to a separate
file. This increases readability and modularity.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
File names such as pcie_ep_bcm_iproc.c / pcie_ep_bcm_iproc_regs.h
seem unnecessarily long, same with CONFIG symbols' names.
Let's shorten them by replacing 'bcm_iproc' with simply 'iproc'.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Listen func goes through a chain of calls to call winc1500_accept.
This is done to install the accept callback and should not block.
This fixes#28953 where winc1500 driver blocks on listen.
Signed-off-by: Nicolai Glud <nicolai.glud@prevas.dk>
