ZEPHYR_SDK_INSTALL_DIR will be set as an internal CMake variable when
using the Zephyr SDK.
The Zephyr SDK zephyr/host-tools.cmake will ensure to set the CMake
ZEPHYR_SDK_INSTALL_DIR variable to the environment setting, or the
install directory in case the CMake package was used.
Users not using the environment variable will experience the following
error:
```
Linking C executable zephyr/.../bootloader/bootloader.elf
FAILED: zephyr/.../bootloader/bootloader.elf
<path>/xtensa-zephyr-elf/bin/ld: cannot find -lhal
```
This commit ensures code build correctly both when setting the
environment variable ZEPHYR_SDK_INSTALL_DIR, and when using Zephyr SDK
CMake `find_package(Zephyr-sdk)`
Signed-off-by: Torsten Rasmussen <Torsten.Rasmussen@nordicsemi.no>
This patch introduces the support of low power modes
for the STM32WBxx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes have lptimer as wakeup source.
The sleep modes are configured by the SYS_POWER_MANAGEMENT.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
Add initial support for nuvoton numicro m48x SoC series, basic
init and uart functionality are covered with gpio and clock
directly relies on HAL.
Signed-off-by: Saravanan Sekar <saravanan@linumiz.com>
This enables PWM and connects it to the main LED. Tested by running
samples/basic/blinky_pwm and /fade_led.
Signed-off-by: Michael Hope <mlhx@google.com>
The SAM0 Timer/Counter for Control Applications can act as a counter
or generator. Add a binding for the TCC in PWM mode and helper to
check the compat mode.
Signed-off-by: Michael Hope <mlhx@google.com>
Add reset interrupt handlers for all three types of reset
interrupts that iProc PCIe EP can receive - namely PERST,
INB PERST and FLR.
Signed-off-by: Shivaraj Shetty <shivaraj.shetty@broadcom.com>
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Change the SAM0 to match other boards by selecting the SAM0 specific
driver when a driver class is selected.
For example, automatically enable CONFIG_SPI_SAM0 when CONFIG_SPI is
enabled.
Signed-off-by: Michael Hope <mlhx@google.com>
Only boards with at least 64K Flash will activate MPU because:
MPU + UERSPACE + All switches implicity activated
(CONFIG_MPU_STACK_GUARD, CONFIG_ARM_STACK_PROTECTION ...)
will consume about 40K Flash
(value computed on nucleo_f767_zi on tests/arch/arm/arm_ramfunc/).
Signed-off-by: Alexandre Bourdiol <alexandre.bourdiol@st.com>
The PWM drivers has been refactored using the HAL LL API. Not only that,
but the set pin_set function is now faster, as channel output compare is
just initialized if needed.
NOTE: Has been tested using H743zi board for now.
Signed-off-by: Gerard Marull-Paretas <gerard@teslabs.com>
Previously, DTS specification of physical RAM bounds did not
correspond to the actual bounds of system RAM as the first
megabyte was being skipped.
There were reasons for this - the first 1MB on PC-like systems
is a no-man's-land of reserved memory regions, but we need DTS
to accurately capture physical memory bounds.
Instead, we introduce a config option which can apply an offset
to the beginning of physical memory, and apply this to the "RAM"
region defined in the linker scripts.
This also fixes a problem where an extra megabyte was being
added to the size of system RAM.
Signed-off-by: Andrew Boie <andrew.p.boie@intel.com>
Introduced interface for efficient logging from external logsystems:
Added handling of vaargs and automatic strdup to macros intended
to be used in logging interface function. Fast path to less then 4
arguments to speed up the execution. Made log_count_args external,
if external logsystem cannot count arguments.
Signed-off-by: Tomasz Konieczny <tomasz.konieczny@nordicsemi.no>
Those MCUs have 2KB RAM and 16KB FLASH memory, but they are still
powerful enough to run small configuration of Zephyr RTOS.
Signed-off-by: Marcin Niestroj <m.niestroj@grinn-global.com>
Added / Tested support for RNG on the STM32F767ZI nucleo board.
Updated the SoC defconfig to auto-enable the driver when
ENTROPY_GENERATOR is enabled, and updated the board README.
Signed-off-by: Bilal Wasim <bilalwasim676@gmail.com>
- Change default CPU Clock to 240MHz
(PLL is activated)
- I2C, UART will use sysclk from clock driver
- esp32_enable_peripheral replaced by
clock_control_on
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
- Support PLL for Higher Frequencies 80,160,240 MHz
- Support XTAL Frequencies 26MHz, 40MHz
- Clock Driver can't be disabled, because all of the other drivers
will depend on it to get their operating Frequency based on chosen
clock source (XTAL/PLL).
- Add needed references to BBPLL i2c bus ROM functions.
- Add `rtc` node to Device Tree.
- Since All Peripherals Frequency is depending on CPU_CLK Source,
`clock-source` property added to CPU node
Signed-off-by: Mohamed ElShahawi <ExtremeGTX@hotmail.com>
This patch introduces the support of low power modes
for the STM32L4xx from STMicroelectronics based on the lptim
Here, the power modes are sleep modes with lptimer as wakeup.
Depending on the SYS_POWER_MANAGEMENT configuration.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
tested on mimxrt1060_evt
MEMORY_NOCACHE is needed
test on frdmk64f
special test slot need configure with
CONFIG_DMA_TEST_SLOT_START
Signed-off-by: Hake Huang <hake.huang@oss.nxp.com>
Remove Kconfig, linker script, and related bits associated with
CUSTOM_RODATA_LD, CUSTOM_RWDATA_LD, CUSTOM_SECTIONS_LD,
SOC_NOINIT_LD, SOC_RODATA_LD, and SOC_RWDATA_LD options that have been
deprecated since Zephyr 2.2.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
This option controls whether additional BLE support is
enabled for the cc13xx_cc26xx platform in hal/ti and
subsys/bluetooth.
Signed-off-by: Christopher Friedt <chrisfriedt@gmail.com>
Introduce switch to allow board configuration for VCI pins to
remain HW-controled depending on the design.
Currently pins are always configured as GPIOs which is not always
desirable.
Signed-off-by: Jose Alberto Meza <jose.a.meza.arellano@intel.com>
The NXP's Kinetics K66F is able to run with max frequency of 180MHz.
To achieve this goal the SMC's PMPROT and PMCTRL registers need to be
adjusted.
On the contrary the K64F doesn't support HSRUN run mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This option enables support for High Speed RUN operation mode for
K66F. The K64F SoC doesn't support this mode.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Add the necessary clock configuration to support STM32L-based
SoCs. This change likely adds support for other STM32 SoCs as well
since the HSI48 clock is configured for all SoCs that support it
(except the STM32L4x) instead of just the STM32G4X.
Signed-off-by: Andreas Sandberg <andreas@sandberg.pp.se>
emsdp_em7d_esp is a board with secure just like em_starterkit_em7d,
but the secure feature not configed in defconfig file. we need to add
below configs in emsdp_em7d_esp_defconfig files:
CONFIG_ARC_HAS_SECURE=y
CONFIG_TRUSTED_EXECUTION_SECURE=y
when secure feature enabled, we use secure timer for system tick, so
we need to add below macro for secure timer:
#define IRQ_SEC_TIMER0 20
Signed-off-by: Watson Zeng <zhiwei@synopsys.com>
This commit fixes Cortex-M header inclusions from the deprecated paths.
The Cortex-M headers were relocated from `include/arch/arm/cortex_m` to
`include/arch/arm/aarch32/cortex_m` by the refactoring done in the
commit d048faacf2.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
Now when we're finally ready to open QEMU port for ARC
we introduce the first ever platform it supports and in fact does
that quite well - Zephyr RTOS.
For now we only offer support of basic EM & HS code execution,
built-in timers, interrupt controller and set of very simple
peripherals: DW UART & optionally MMIO Virtio devices.
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
This is defining the SYS_CLOCK_TICKS_PER_SEC default value
depending on the LPTIM CLOCK frequency in case of LPTIMER,
to get a TICK value as a divider of the LPTIM clock source.
It gives a better result in formulas when converting
ticks to count unit.
Signed-off-by: Francois Ramu <francois.ramu@st.com>
This adds a helper function for reading LiteX 64-bit CSRs
to be used by LiteX drivers.
Signed-off-by: Jakub Cebulski <jcebulski@internships.antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
emsdp is a FPGA based platform, can be loaded with different
configurations. Different configuration have different
interrupts:
* em5d, em7d and em11d have 111 interrupts
* em4 and em6 have 113 interrupts
* em7d_esp has 112 interrupts
Signed-off-by: Wayne Ren <wei.ren@synopsys.com>
UARTs and I2C controllers are accessed through MMIO and
these regions need to be added to MMU for proper access.
This also enable MMU for Apollo Lake by default since
serial console is now usable.
Signed-off-by: Daniel Leung <daniel.leung@intel.com>
This file consists only of an array of per-CPU IOAPIC ID's that
overrides the weak symbol defined by the architecture.
The IOAPIC IDs are only used when targetting a startup IPI for the
auxiliary right now, but the IDs are the IDs and represent hardware
truth. They should be correct even if unused.
Using the wrong ones also breaks the tests/kernel/mp test, which calls
arch_start_cpu() when not in SMP mode as a deliberate unit test.
Signed-off-by: Andy Ross <andrew.j.ross@intel.com>
The APIC timer is not supported e.g. with SMP (which will be enabled
by default soon as well) so the sensible choice is to default to HPET.
Also, the default makes more sense to be on the SoC side, so move it
there from the board defaults.
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
The nodelabel references for the GPIO region MMU setup were incorrect.
The nodelabel names didn't match what is in the dts. Fix this otherwise
we get a compile error when enabling the functionality.
Signed-off-by: Kumar Gala <kumar.gala@linaro.org>
Several reviewers agreed that DT_HAS_NODE_STATUS_OKAY(...) was an
undesirable API for the following reasons:
- it's inconsistent with the rest of the DT_NODE_HAS_FOO names
- DT_NODE_HAS_FOO_BAR_BAZ(node) was agreed upon as a shorthand
for macros which are equivalent to
DT_NODE_HAS_FOO(node) && DT_NODE_HAS_BAR(node) &&
- DT_NODE_HAS_BAZ(node), and DT_HAS_NODE_STATUS_OKAY is an odd duck
- DT_NODE_HAS_STATUS(..., okay) was viewed as more readable anyway
- it is seen as a somewhat aesthetically challenged name
Replace all users with DT_NODE_HAS_STATUS(..., okay), which is
semantically equivalent.
This is mostly done with sed, but a few remaining cases were done by
hand, along with whitespace, docs, and comment changes. These special
cases include the Nordic SOC static assert files.
Signed-off-by: Martí Bolívar <marti.bolivar@nordicsemi.no>
The Atmel SAM D21 SoC, according to the original Atmel datasheet
(Atmel-42181N), has 28 interrupt lines (0-27).
There have been mysterious changes in the number of interrupt lines and
on-chip peripherals in the recent Microchip datasheet releases, but
there is no explicit information available for this (e.g. PCN), so we
take the safest approach by assuming the lowest interrupt line number.
Signed-off-by: Stephanos Ioannidis <root@stephanos.io>
